- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- About your printer
- Printer features
- Support menu (MK3/S/+)
Support menu (MK3/S/+)
- Printer description
- Printer features
- Accelerometer (MK4/S, MK3.9/S)
- Brightness adjustment (SL1)
- Buddy firmware-specific G-code commands
- Cancel Object (MK4/S, MK3.9/S, XL, MINI/+)
- Crash detection
- Crash dump
- Creating a resin calibration object (SL1/SL1S)
- Dump memory (MK3/S/+ and MK2.5/S)
- Experimental menu (MK3/S/+)
- Experimental settings (MK4/S, MK3.9/S, MK3.5/S, XL, MINI/+)
- Filament sensor (MK4, MK3.9, XL)
- Filament sensor MK3 (non-S)
- Flashing custom firmware (MK4/S, MK3.9/S, MK3.5/S)
- Flexible steel sheets (guidepost)
- GPIO Module
- High flow print head (HT90)
- High temperature print head (HT90)
- HW setup (MINI/MINI+)
- HW setup (MK2.5/S & MK3/S/+)
- Internet connection (SL1/SL1S)
- IR Filament Sensor (MK2.5S, MK3S/+, MK3.5/S)
- IR Filament sensor detection (MK3S)
- LCD brightness adjustment (MK3S)
- LCD screen contrast adjustment (i3)
- Loadcell (MK4/S, MK3.9/S, XL)
- Menu structure (SL1/SL1S)
- MMU3 Prusa Nozzle vs. CHT nozzle
- Model preview
- Network Connection (MK4S, MK3.9S)
- Nextruder silicone sock (XL, MK4, MK3.9)
- NFC antenna
- Noisy filament sensor (MINI)
- One-click print
- Pouring resin and starting print
- Power Panic
- Power-modes
- PP steel sheet
- Print Profile (SL1/SL1S)
- Print statistics
- Printer statistics and system information (SL1/SL1S)
- Pronterface and USB cable
- Prusa firmware-specific G-code commands
- Prusa Pro Filament Drybox
- Resin Calibration (SL1/SL1S)
- Resin Tank Cleaning (SL1/SL1S)
- Satin steel sheet
- SD card sorting
- Smooth Steel Sheet
- Sound mode (MINI/MINI+)
- Special PA Nylon steel sheet
- SpoolJoin (MMU2S)
- Steel sheet profiles
- Stuck filament detection #26101 (MK4S) #13101 (MK4) #21101 (MK3.9) #17108 (XL)
- Support menu (MK3/S/+)
- Immediate info
- XYZ calibration detail
- Extruder info
- Sensor info
- Belt status
- Temperatures
- Voltages
- Support settings for the XL
- Textured steel sheet
- Thermal model calibration
- Tools Mapping (XL)
- Tools Mapping and Filament Mapping (XL, MMU3)
- Top-bar Notifications (SL1/SL1S)
- Touch screen (MK4/S, MK3.9/S, MK3.5/S, XL)
- Tune Menu
- Water-soluble materials (PVA/BVOH)
- General Information
At the bottom of the LCD menu on the Original Prusa MK2.5/S and MK3/S/+, you will find information on your specific machine's hardware, and firmware as well as real-time sensor inputs, voltages, temperature readings, and more. This section contains valuable information when troubleshooting specific components, or if you need information specific to your unit.
Immediate info
- Firmware version
- Useful links
- EINSY mainboard revision
- Fil. sensor state and version
- MMU2S presence and firmware
- IP (if connected to a network)
XYZ calibration detail
This contains info regarding the length of the axis, skew, and offsets.
Extruder info
Contains the RPM (Revolutions Per Minute) reading from both the Nozzle fan and the Hotend fan
Sensor info
Contains the real-time state (1 or 0) of the printer's filament sensor, PINDA, and FINDA (if MMU2S is installed).
Belt status
Contains the value given to the measurement of the X and Y belt tension. A lower value means a tighter belt.
Temperatures
Real-time readings from the thermistors located on the Hotend, Heatbed, Einsy Rambo (Ambient), and P.I.N.D.A. V2 (Not present with P.I.N.D.A. V1/SuperPINDA).
Voltages
Display the voltage delivered to the EINSy Rambo, Heatbed, and IR filament sensor.
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.