EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- Calibration
- Calibration Error Messages
- UV LED calibrator link error #10313 (SL1)
UV LED calibrator link error #10313 (SL1)
Menu
- Basic calibration
- Advanced calibration
- Calibration Error Messages
- Boot slot changed #10601 (SL1/SL1S)
- Calibration error #10113 (SL1/SL1S)
- Calibration failed
- Calibration load failed #10524 (SL1)
- Cannot set update channel #10513 (SL1/SL1S)
- Check Axis Length X/Y/Z (MK3S)
- Data overwrite failed #10530 (SL1/SL1S)
- Data preparation failure #10525 (SL1/SL1S)
- Display usage error #10535 (SL1)
- Distance between tip of the nozzle and the bed surface has not been set yet
- End-stop not hitting
- Fan RPM not in range #10122 (SL1/SL1S)
- Hostname error #10536 (SL1/SL1S)
- Internal error (DBUS mapping failed) #10507 (SL1/SL1S)
- Invalid tilt align position #10121 (SL1/SL1S)
- No UV calibration data #10532 (SL1)
- Printer has not been calibrated yet
- Printer is not UV calibrated #10308 (SL1)
- Printer Variant Mismatch #10711 (SL1/SL1S)
- QR Error codes
- Serial number error #10527 (SL1/SL1S)
- SL1 Tilt-mechanism error
- Speaker test failed #10310 (SL1/SL1S)
- Static memory has been overwritten
- This Wizard cannot be canceled #10522 (SL1/SL1S)
- Tilt check failed #10119 (SL1/SL1S)
- Tilt endstop not reached #10115 (SL1/SL1S)
- Tilt homing failed #10101 (SL1/SL1S)
- Tower endstop not reached #10114 (SL1/SL1S)
- Tower homing failed #10102 (SL1/SL1S)
- Tower moving failed #10103 (SL1/SL1S)
- Tower position error #10123 (SL1/SL1S)
- UV calibration error #10319 (SL1)
- UV data error #10533 (SL1)
- UV intensity too high #10317 (SL1/SL1S)
- UV intensity too low #10318 (SL1/SL1S)
- UV LED calibrator connection error #10312 (SL1)
- UV LED calibrator error #10314 (SL1)
- UV LED calibrator link error #10313 (SL1)
- What happened?
- How to fix it?
- Guides
- UV LED calibrator not detected #10311 (SL1)
- UV LED calibrator readings error #10315 (SL1)
- UV LED heatsink overheating #10206 (SL1)
- Wizard data failure #10526 (SL1/SL1S)
- XYZ Calibration error-messages (MK2/S)
- XYZ-calibration error-messages (MK3/MK3S/MK3S+)
Relevant for:
Last updated 4 years agoThis article is also available in following languages: 
What happened?
The printer is displaying the message: Communication with the UV LED calibrator has failed. Check the connection and try again.
Error name: UV LED calibrator link error
Error code: #10313
How to fix it?
The UV calibrator is detected, but can not be communicated with. It must be connected to the front USB port when instructed or before the calibration has started.
If the UV calibrator is connected correctly, try to update the firmware and restart the machine. If it persists, the UV calibrator may be broken and you should contact Customer support.
Guides
Was this article helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.