Firmware i pliki

New features

• HT hotend support with automatic hotend detection
• PPS and PPA filament presets for the HT hotend
• PVA and BVOH filament presets
• Filament color support
• Tool mapping presets and Smart mapping
• Automatic Z-axis alignment on uneven bed
• Runout Reaction setting for instant or delayed runout handling (#5423)

Changes and improvements

• New versioning policy
• Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
• Reorganized Tune menu [6.9.0]
• Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
• Stuck filament dialog now offers Ignore and Disable options [6.9.0]
• Improved Nozzle Wiper cleaning [6.10.1]
• Parking now lifts the Z axis faster [6.10.2]
• Heater selftest now lowers the bed further to leave room for hands [6.9.1]
• Chamber vents now close automatically at the end of a print [6.9.0]
• Filament sensor selftest now detects a disconnected sensor [6.9.0]
• G-code lines sent over USB/serial that are too long now show a warning
• PrusaLink file downloads now keep long file names
• Prusa Connect now shows changed chamber, fan and light values within seconds
• MMU filament menu now shows the loaded filament and its color [MMU]

Fixes

• Improved security and robustness
• Fixed unreliable homing [C1/+] [6.9.1]
• Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
• Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
• Fixed chamber temperature serial reporting format
• Fixed an extra blob of filament when resuming after a power failure [6.9.0]
• Fixed settings being lost when power was cut while they were being saved [6.10.1]
• Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
• Fixed the Not enough tools G-code check blocking prints with no way to bypass it
• Fixed a crash when the door was opened during homing
• Fixed wrong remaining time after resuming from a power failure [6.9.0]
• Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
• Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
• Fixed a crash on the print preview screen
• Fixed text overflowing on the factory reset screen
• Fixed a crash when changing Front PTFE Length [MMU]
• Fixed tool mapping being ignored when starting a print from Prusa Connect
• Display glitch recovery now also works on error and boot screens
• Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

• New features
  • HT hotend support with automatic hotend detection
  • PPS and PPA filament presets for the HT hotend
  • PVA and BVOH filament presets
  • Filament color support
  • Tool mapping presets and Smart mapping
  • Automatic Z-axis alignment on uneven bed
  • Runout Reaction setting for instant or delayed runout handling (#5423)
• Changes and improvements
  • New versioning policy
  • Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
  • Reorganized Tune menu [6.9.0]
  • Tool mapping is now preserved when reprinting a job [6.9.0]
  • New Customize button for tweaking a loaded filament
  • Stuck filament dialog now offers Ignore and Disable options [6.9.0]
  • Improved Nozzle Wiper cleaning [6.10.1]
  • Parking now lifts the Z axis faster [6.10.2]
  • Heater selftest now lowers the bed further to leave room for hands [6.9.1]
  • Chamber vents now close automatically at the end of a print [6.9.0]
  • Filament sensor selftest now detects a disconnected sensor [6.9.0]
  • G-code lines sent over USB/serial that are too long now show a warning
  • PrusaLink file downloads now keep long file names
  • Prusa Connect now shows changed chamber, fan and light values within seconds
  • MMU filament menu now shows the loaded filament and its color [MMU]
• Fixes
  • Fixed unreliable homing [C1/+] [6.9.1]
  • Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
  • Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
  • Fixed chamber temperature serial reporting format
  • Fixed an extra blob of filament when resuming after a power failure [6.9.0]
  • Fixed settings being lost when power was cut while they were being saved [6.10.1]
  • Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
  • Fixed the Not enough tools G-code check blocking prints with no way to bypass it
  • Fixed a crash when the door was opened during homing
  • Fixed wrong remaining time after resuming from a power failure [6.9.0]
  • Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
  • Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
  • Fixed a crash on the print preview screen
  • Fixed text overflowing on the factory reset screen
  • Fixed a crash when changing Front PTFE Length [MMU]
  • Fixed tool mapping being ignored when starting a print from Prusa Connect
  • Display glitch recovery now also works on error and boot screens
  • Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

• New features
  • HT hotend support with automatic hotend detection
  • PPS and PPA filament presets for the HT hotend
  • PVA and BVOH filament presets
  • Filament color support
  • Tool mapping presets and Smart mapping
  • Automatic Z-axis alignment on uneven bed
  • Runout Reaction setting for instant or delayed runout handling (#5423)
  • Changes and improvements

• New versioning policy
  • Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
  • Reorganized Tune menu [6.9.0]
  • Tool mapping is now preserved when reprinting a job [6.9.0]
  • New Customize button for tweaking a loaded filament
  • Stuck filament dialog now offers Ignore and Disable options [6.9.0]
  • Improved Nozzle Wiper cleaning [6.10.1]
  • Parking now lifts the Z axis faster [6.10.2]
  • Heater selftest now lowers the bed further to leave room for hands [6.9.1]
  • Chamber vents now close automatically at the end of a print [6.9.0]
  • Filament sensor selftest now detects a disconnected sensor [6.9.0]
  • G-code lines sent over USB/serial that are too long now show a warning
  • PrusaLink file downloads now keep long file names
  • Prusa Connect now shows changed chamber, fan and light values within seconds
  • MMU filament menu now shows the loaded filament and its color [MMU]

• Fixes
  • Fixed unreliable homing [C1/+] [6.9.1]
  • Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
  • Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
  • Fixed chamber temperature serial reporting format
  • Fixed an extra blob of filament when resuming after a power failure [6.9.0]
  • Fixed settings being lost when power was cut while they were being saved [6.10.1]
  • Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
  • Fixed the Not enough tools G-code check blocking prints with no way to bypass it
  • Fixed a crash when the door was opened during homing
  • Fixed wrong remaining time after resuming from a power failure [6.9.0]
  • Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
  • Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
  • Fixed a crash on the print preview screen
  • Fixed text overflowing on the factory reset screen
  • Fixed a crash when changing Front PTFE Length [MMU]
  • Fixed tool mapping being ignored when starting a print from Prusa Connect
  • Display glitch recovery now also works on error and boot screens
  • Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

• New features
  • HT hotend support with automatic hotend detection
  • PPS and PPA filament presets for the HT hotend
  • PVA and BVOH filament presets
  • Filament color support
  • Tool mapping presets and Smart mapping
  • Automatic Z-axis alignment on uneven bed
  • Runout Reaction setting for instant or delayed runout handling (#5423)
  • Changes and improvements
  • New versioning policy
  • Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
  • Reorganized Tune menu [6.9.0]
  • Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
  • Stuck filament dialog now offers Ignore and Disable options [6.9.0]
  • Improved Nozzle Wiper cleaning [6.10.1]
  • Parking now lifts the Z axis faster [6.10.2]
  • Heater selftest now lowers the bed further to leave room for hands [6.9.1]
  • Chamber vents now close automatically at the end of a print [6.9.0]
  • Filament sensor selftest now detects a disconnected sensor [6.9.0]
  • G-code lines sent over USB/serial that are too long now show a warning
  • PrusaLink file downloads now keep long file names
  • Prusa Connect now shows changed chamber, fan and light values within seconds
  • MMU filament menu now shows the loaded filament and its color [MMU]
• Fixes
  • Improved security and robustness
  • Fixed unreliable homing [C1/+] [6.9.1]
  • Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
  • Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
  • Fixed chamber temperature serial reporting format
  • Fixed an extra blob of filament when resuming after a power failure [6.9.0]
  • Fixed settings being lost when power was cut while they were being saved [6.10.1]
  • Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
  • Fixed the Not enough tools G-code check blocking prints with no way to bypass it
  • Fixed a crash when the door was opened during homing
  • Fixed wrong remaining time after resuming from a power failure [6.9.0]
  • Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
  • Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
  • Fixed a crash on the print preview screen
  • Fixed text overflowing on the factory reset screen
  • Fixed a crash when changing Front PTFE Length [MMU]
  • Fixed tool mapping being ignored when starting a print from Prusa Connect
  • Display glitch recovery now also works on error and boot screens
  • Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

• Nowe funkcje
  • Nowe edycje: CORE One+ (Gen 2) oraz CORE One L+
  • Obsługa wycieraczki dyszy, zastępująca poprzednią procedurę czyszczenia dyszy przed rozpoczęciem wydruku
  • Obsługa pasków GT1.5
  • Obsługa złączy kompensacyjnych Gen 2, ze znacznie krótszą fazą pochłaniania ciepła [C1+ (Gen 2)]
  • Natychmiastowe zatrzymanie w przypadku wyczerpania się filamentu
  • Wspomagana kolejność kalibracji - kalibracje i testy deklarują swoje warunki wstępne
• Zmiany i ulepszenia
  • Przeorganizowane menu - niektóre ustawienia zostały przeniesione do innych podmenu.
  • Kontrola kompatybilności filamentu w większej liczbie miejsc
  • Własne nazwy filamentu mogą zawierać małe litery
• Poprawki
  • Naprawiono przywracanie pierwotnej temperatury po wyczerpaniu filamentu lub zmianie w trakcie wydruku
  • Większa niezawodność komunikacji z płytką rozszerzeń xBuddy Extension
  • Poprawka widoczności ostatniego pliku w folderze i powiązane poprawki listy plików
  • Drukarka nie wydaje już dźwięku przy uruchamianiu w trybie cichym
  • Przesunięcie palcem w górę po ekranie dotykowym nie jest już rejestrowane jako stuknięcie
  • I znacznie więcej

New features

• HT hotend support with automatic hotend detection
• PPS and PPA filament presets for the HT hotend
• PVA and BVOH filament presets
• Filament color support
• Tool mapping presets and Smart mapping
• Automatic Z-axis alignment on uneven bed
• Runout Reaction setting for instant or delayed runout handling (#5423)

Changes and improvements

• New versioning policy
• Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
• Reorganized Tune menu [6.9.0]
• Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
• Stuck filament dialog now offers Ignore and Disable options [6.9.0]
• Improved Nozzle Wiper cleaning [6.10.1]
• Parking now lifts the Z axis faster [6.10.2]
• Heater selftest now lowers the bed further to leave room for hands [6.9.1]
• Chamber vents now close automatically at the end of a print [6.9.0]
• Filament sensor selftest now detects a disconnected sensor [6.9.0]
• G-code lines sent over USB/serial that are too long now show a warning
• PrusaLink file downloads now keep long file names
• Prusa Connect now shows changed chamber, fan and light values within seconds
• MMU filament menu now shows the loaded filament and its color [MMU]

Fixes

• Improved security and robustness
• Fixed unreliable homing [C1/+] [6.9.1]
• Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
• Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
• Fixed chamber temperature serial reporting format
• Fixed an extra blob of filament when resuming after a power failure [6.9.0]
• Fixed settings being lost when power was cut while they were being saved [6.10.1]
• Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
• Fixed the Not enough tools G-code check blocking prints with no way to bypass it
• Fixed a crash when the door was opened during homing
• Fixed wrong remaining time after resuming from a power failure [6.9.0]
• Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
• Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
• Fixed a crash on the print preview screen
• Fixed text overflowing on the factory reset screen
• Fixed a crash when changing Front PTFE Length [MMU]
• Fixed tool mapping being ignored when starting a print from Prusa Connect
• Display glitch recovery now also works on error and boot screens
• Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

Dodano kompatybilność z Gen 2

• New features
  • HT hotend support with automatic hotend detection
  • PPS and PPA filament presets for the HT hotend
  • PVA and BVOH filament presets
  • Filament color support
  • Tool mapping presets and Smart mapping
  • Automatic Z-axis alignment on uneven bed
  • Runout Reaction setting for instant or delayed runout handling (#5423)
• Changes and improvements
  • New versioning policy
  • Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
  • Reorganized Tune menu [6.9.0]
  • Tool mapping is now preserved when reprinting a job [6.9.0]
  • New Customize button for tweaking a loaded filament
  • Stuck filament dialog now offers Ignore and Disable options [6.9.0]
  • Improved Nozzle Wiper cleaning [6.10.1]
  • Parking now lifts the Z axis faster [6.10.2]
  • Heater selftest now lowers the bed further to leave room for hands [6.9.1]
  • Chamber vents now close automatically at the end of a print [6.9.0]
  • Filament sensor selftest now detects a disconnected sensor [6.9.0]
  • G-code lines sent over USB/serial that are too long now show a warning
  • PrusaLink file downloads now keep long file names
  • Prusa Connect now shows changed chamber, fan and light values within seconds
  • MMU filament menu now shows the loaded filament and its color [MMU]
• Fixes
  • Improved security and robustness
  • Fixed unreliable homing [C1/+] [6.9.1]
  • Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
  • Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
  • Fixed chamber temperature serial reporting format
  • Fixed an extra blob of filament when resuming after a power failure [6.9.0]
  • Fixed settings being lost when power was cut while they were being saved [6.10.1]
  • Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
  • Fixed the Not enough tools G-code check blocking prints with no way to bypass it
  • Fixed a crash when the door was opened during homing
  • Fixed wrong remaining time after resuming from a power failure [6.9.0]
  • Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
  • Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
  • Fixed a crash on the print preview screen
  • Fixed text overflowing on the factory reset screen
  • Fixed a crash when changing Front PTFE Length [MMU]
  • Fixed tool mapping being ignored when starting a print from Prusa Connect
  • Display glitch recovery now also works on error and boot screens
  • Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

Nowe funkcje:

• Obraz firmware podpisany przez dostawcę w celu zapobiegania złośliwym atakom wykorzystującym firmware innych producentów 

Poprawki błędów:

• Ograniczono uprawnienia systemu plików USB w celu wyeliminowania potencjalnego wektora ataku
• Ograniczono uprawnienia komponentów Klippera w celu wyeliminowania potencjalnych wektorów ataku
• Usunięto nieużywane fragmenty kodu źródłowego w celu wyeliminowania potencjalnych wektorów ataku
• Zabezpieczono interfejs API REST drukarki przed potencjalnym wstrzyknięciem złośliwego kodu
• Usunięto dostęp przez SSH
• Naprawiono sprawdzanie poprawności nazwy drukarki zgodnie z RFC 1123

Dokumenty:

• Treść dotycząca bezpieczeństwa firmware Prusa Pro HT90 w wersji 1.3.56, identyfikator biuletynu bezpieczeństwa: PSA-2026-001

• Obsługa Prusa Connect
• Własne profile druku
• Aktualizacja PrusaLink Web
• Limity czasu naświetlania
• Poprawiona obsługa pamięci USB
• Wyłączono obsługę kluczy API
• Inne ulepszenia
• Poprawki błędów
• Znane problemy

• Wydłużenie wszystkich timerów do 255 minut
• Filtrowanie IPA (nowa funkcja)
• Cykle mycia (nowa funkcja)
• Nowy algorytm podgrzewania
• Automatyczne sterowanie wentylatorami
• Opcja resetu fabrycznego
• Ulepszony Selftest
• Poprawki błędów

• New features
  • HT hotend support with automatic hotend detection
  • PPS and PPA filament presets for the HT hotend
  • PVA and BVOH filament presets
  • Filament color support
  • Tool mapping presets and Smart mapping
  • Automatic Z-axis alignment on uneven bed
  • Runout Reaction setting for instant or delayed runout handling (#5423)
  • Changes and improvements
  • New versioning policy
  • Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
  • Reorganized Tune menu [6.9.0]
  • Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
  • Stuck filament dialog now offers Ignore and Disable options [6.9.0]
  • Improved Nozzle Wiper cleaning [6.10.1]
  • Parking now lifts the Z axis faster [6.10.2]
  • Heater selftest now lowers the bed further to leave room for hands [6.9.1]
  • Chamber vents now close automatically at the end of a print [6.9.0]
  • Filament sensor selftest now detects a disconnected sensor [6.9.0]
  • G-code lines sent over USB/serial that are too long now show a warning
  • PrusaLink file downloads now keep long file names
  • Prusa Connect now shows changed chamber, fan and light values within seconds
  • MMU filament menu now shows the loaded filament and its color [MMU]
• Fixes
  • Improved security and robustness
  • Fixed unreliable homing [C1/+] [6.9.1]
  • Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
  • Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
  • Fixed chamber temperature serial reporting format
  • Fixed an extra blob of filament when resuming after a power failure [6.9.0]
  • Fixed settings being lost when power was cut while they were being saved [6.10.1]
  • Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
  • Fixed the Not enough tools G-code check blocking prints with no way to bypass it
  • Fixed a crash when the door was opened during homing
  • Fixed wrong remaining time after resuming from a power failure [6.9.0]
  • Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
  • Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
  • Fixed a crash on the print preview screen
  • Fixed text overflowing on the factory reset screen
  • Fixed a crash when changing Front PTFE Length [MMU]
  • Fixed tool mapping being ignored when starting a print from Prusa Connect
  • Display glitch recovery now also works on error and boot screens
  • Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

• New features
  • HT hotend support with automatic hotend detection
  • PPS and PPA filament presets for the HT hotend
  • PVA and BVOH filament presets
  • Filament color support
  • Tool mapping presets and Smart mapping
  • Automatic Z-axis alignment on uneven bed
  • Runout Reaction setting for instant or delayed runout handling (#5423)
• Changes and improvements
  • New versioning policy
  • Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
  • Reorganized Tune menu [6.9.0]
  • Tool mapping is now preserved when reprinting a job [6.9.0]
  • New Customize button for tweaking a loaded filament
  • Stuck filament dialog now offers Ignore and Disable options [6.9.0]
  • Improved Nozzle Wiper cleaning [6.10.1]
  • Parking now lifts the Z axis faster [6.10.2]
  • Heater selftest now lowers the bed further to leave room for hands [6.9.1]
  • Chamber vents now close automatically at the end of a print [6.9.0]
  • Filament sensor selftest now detects a disconnected sensor [6.9.0]
  • G-code lines sent over USB/serial that are too long now show a warning
  • PrusaLink file downloads now keep long file names
  • Prusa Connect now shows changed chamber, fan and light values within seconds
  • MMU filament menu now shows the loaded filament and its color [MMU]
• Fixes
  • Fixed unreliable homing [C1/+] [6.9.1]
  • Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
  • Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
  • Fixed chamber temperature serial reporting format
  • Fixed an extra blob of filament when resuming after a power failure [6.9.0]
  • Fixed settings being lost when power was cut while they were being saved [6.10.1]
  • Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
  • Fixed the Not enough tools G-code check blocking prints with no way to bypass it
  • Fixed a crash when the door was opened during homing
  • Fixed wrong remaining time after resuming from a power failure [6.9.0]
  • Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
  • Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
  • Fixed a crash on the print preview screen
  • Fixed text overflowing on the factory reset screen
  • Fixed a crash when changing Front PTFE Length [MMU]
  • Fixed tool mapping being ignored when starting a print from Prusa Connect
  • Display glitch recovery now also works on error and boot screens
  • Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

• New features
  • HT hotend support with automatic hotend detection
  • PPS and PPA filament presets for the HT hotend
  • PVA and BVOH filament presets
  • Filament color support
  • Tool mapping presets and Smart mapping
  • Automatic Z-axis alignment on uneven bed
  • Runout Reaction setting for instant or delayed runout handling (#5423)
  • Changes and improvements

• New versioning policy
  • Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
  • Reorganized Tune menu [6.9.0]
  • Tool mapping is now preserved when reprinting a job [6.9.0]
  • New Customize button for tweaking a loaded filament
  • Stuck filament dialog now offers Ignore and Disable options [6.9.0]
  • Improved Nozzle Wiper cleaning [6.10.1]
  • Parking now lifts the Z axis faster [6.10.2]
  • Heater selftest now lowers the bed further to leave room for hands [6.9.1]
  • Chamber vents now close automatically at the end of a print [6.9.0]
  • Filament sensor selftest now detects a disconnected sensor [6.9.0]
  • G-code lines sent over USB/serial that are too long now show a warning
  • PrusaLink file downloads now keep long file names
  • Prusa Connect now shows changed chamber, fan and light values within seconds
  • MMU filament menu now shows the loaded filament and its color [MMU]

• Fixes
  • Fixed unreliable homing [C1/+] [6.9.1]
  • Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
  • Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
  • Fixed chamber temperature serial reporting format
  • Fixed an extra blob of filament when resuming after a power failure [6.9.0]
  • Fixed settings being lost when power was cut while they were being saved [6.10.1]
  • Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
  • Fixed the Not enough tools G-code check blocking prints with no way to bypass it
  • Fixed a crash when the door was opened during homing
  • Fixed wrong remaining time after resuming from a power failure [6.9.0]
  • Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
  • Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
  • Fixed a crash on the print preview screen
  • Fixed text overflowing on the factory reset screen
  • Fixed a crash when changing Front PTFE Length [MMU]
  • Fixed tool mapping being ignored when starting a print from Prusa Connect
  • Display glitch recovery now also works on error and boot screens
  • Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

New features

• HT hotend support with automatic hotend detection
• PPS and PPA filament presets for the HT hotend
• PVA and BVOH filament presets
• Filament color support
• Tool mapping presets and Smart mapping
• Automatic Z-axis alignment on uneven bed
• Runout Reaction setting for instant or delayed runout handling (#5423)

Changes and improvements

• New versioning policy
• Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
• Reorganized Tune menu [6.9.0]
• Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
• Stuck filament dialog now offers Ignore and Disable options [6.9.0]
• Improved Nozzle Wiper cleaning [6.10.1]
• Parking now lifts the Z axis faster [6.10.2]
• Heater selftest now lowers the bed further to leave room for hands [6.9.1]
• Chamber vents now close automatically at the end of a print [6.9.0]
• Filament sensor selftest now detects a disconnected sensor [6.9.0]
• G-code lines sent over USB/serial that are too long now show a warning
• PrusaLink file downloads now keep long file names
• Prusa Connect now shows changed chamber, fan and light values within seconds
• MMU filament menu now shows the loaded filament and its color [MMU]

Fixes

• Improved security and robustness
• Fixed unreliable homing [C1/+] [6.9.1]
• Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
• Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
• Fixed chamber temperature serial reporting format
• Fixed an extra blob of filament when resuming after a power failure [6.9.0]
• Fixed settings being lost when power was cut while they were being saved [6.10.1]
• Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
• Fixed the Not enough tools G-code check blocking prints with no way to bypass it
• Fixed a crash when the door was opened during homing
• Fixed wrong remaining time after resuming from a power failure [6.9.0]
• Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
• Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
• Fixed a crash on the print preview screen
• Fixed text overflowing on the factory reset screen
• Fixed a crash when changing Front PTFE Length [MMU]
• Fixed tool mapping being ignored when starting a print from Prusa Connect
• Display glitch recovery now also works on error and boot screens
• Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

New features

• HT hotend support with automatic hotend detection
• PPS and PPA filament presets for the HT hotend
• PVA and BVOH filament presets
• Filament color support
• Tool mapping presets and Smart mapping
• Automatic Z-axis alignment on uneven bed
• Runout Reaction setting for instant or delayed runout handling (#5423)

Changes and improvements

• New versioning policy
• Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
• Reorganized Tune menu [6.9.0]
• Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
• Stuck filament dialog now offers Ignore and Disable options [6.9.0]
• Improved Nozzle Wiper cleaning [6.10.1]
• Parking now lifts the Z axis faster [6.10.2]
• Heater selftest now lowers the bed further to leave room for hands [6.9.1]
• Chamber vents now close automatically at the end of a print [6.9.0]
• Filament sensor selftest now detects a disconnected sensor [6.9.0]
• G-code lines sent over USB/serial that are too long now show a warning
• PrusaLink file downloads now keep long file names
• Prusa Connect now shows changed chamber, fan and light values within seconds
• MMU filament menu now shows the loaded filament and its color [MMU]

Fixes

• Improved security and robustness
• Fixed unreliable homing [C1/+] [6.9.1]
• Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
• Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
• Fixed chamber temperature serial reporting format
• Fixed an extra blob of filament when resuming after a power failure [6.9.0]
• Fixed settings being lost when power was cut while they were being saved [6.10.1]
• Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
• Fixed the Not enough tools G-code check blocking prints with no way to bypass it
• Fixed a crash when the door was opened during homing
• Fixed wrong remaining time after resuming from a power failure [6.9.0]
• Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
• Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
• Fixed a crash on the print preview screen
• Fixed text overflowing on the factory reset screen
• Fixed a crash when changing Front PTFE Length [MMU]
• Fixed tool mapping being ignored when starting a print from Prusa Connect
• Display glitch recovery now also works on error and boot screens
• Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

New features

• HT hotend support with automatic hotend detection
• PPS and PPA filament presets for the HT hotend
• PVA and BVOH filament presets
• Filament color support
• Tool mapping presets and Smart mapping
• Automatic Z-axis alignment on uneven bed
• Runout Reaction setting for instant or delayed runout handling (#5423)

Changes and improvements

• New versioning policy
• Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
• Reorganized Tune menu [6.9.0]
• Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
• Stuck filament dialog now offers Ignore and Disable options [6.9.0]
• Improved Nozzle Wiper cleaning [6.10.1]
• Parking now lifts the Z axis faster [6.10.2]
• Heater selftest now lowers the bed further to leave room for hands [6.9.1]
• Chamber vents now close automatically at the end of a print [6.9.0]
• Filament sensor selftest now detects a disconnected sensor [6.9.0]
• G-code lines sent over USB/serial that are too long now show a warning
• PrusaLink file downloads now keep long file names
• Prusa Connect now shows changed chamber, fan and light values within seconds
• MMU filament menu now shows the loaded filament and its color [MMU]

Fixes

• Improved security and robustness
• Fixed unreliable homing [C1/+] [6.9.1]
• Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
• Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
• Fixed chamber temperature serial reporting format
• Fixed an extra blob of filament when resuming after a power failure [6.9.0]
• Fixed settings being lost when power was cut while they were being saved [6.10.1]
• Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
• Fixed the Not enough tools G-code check blocking prints with no way to bypass it
• Fixed a crash when the door was opened during homing
• Fixed wrong remaining time after resuming from a power failure [6.9.0]
• Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
• Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
• Fixed a crash on the print preview screen
• Fixed text overflowing on the factory reset screen
• Fixed a crash when changing Front PTFE Length [MMU]
• Fixed tool mapping being ignored when starting a print from Prusa Connect
• Display glitch recovery now also works on error and boot screens
• Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

New features

• HT hotend support with automatic hotend detection
• PPS and PPA filament presets for the HT hotend
• PVA and BVOH filament presets
• Filament color support
• Tool mapping presets and Smart mapping
• Automatic Z-axis alignment on uneven bed
• Runout Reaction setting for instant or delayed runout handling (#5423)

Changes and improvements

• New versioning policy
• Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
• Reorganized Tune menu [6.9.0]
• Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
• Stuck filament dialog now offers Ignore and Disable options [6.9.0]
• Improved Nozzle Wiper cleaning [6.10.1]
• Parking now lifts the Z axis faster [6.10.2]
• Heater selftest now lowers the bed further to leave room for hands [6.9.1]
• Chamber vents now close automatically at the end of a print [6.9.0]
• Filament sensor selftest now detects a disconnected sensor [6.9.0]
• G-code lines sent over USB/serial that are too long now show a warning
• PrusaLink file downloads now keep long file names
• Prusa Connect now shows changed chamber, fan and light values within seconds
• MMU filament menu now shows the loaded filament and its color [MMU]

Fixes

• Improved security and robustness
• Fixed unreliable homing [C1/+] [6.9.1]
• Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
• Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
• Fixed chamber temperature serial reporting format
• Fixed an extra blob of filament when resuming after a power failure [6.9.0]
• Fixed settings being lost when power was cut while they were being saved [6.10.1]
• Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
• Fixed the Not enough tools G-code check blocking prints with no way to bypass it
• Fixed a crash when the door was opened during homing
• Fixed wrong remaining time after resuming from a power failure [6.9.0]
• Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
• Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
• Fixed a crash on the print preview screen
• Fixed text overflowing on the factory reset screen
• Fixed a crash when changing Front PTFE Length [MMU]
• Fixed tool mapping being ignored when starting a print from Prusa Connect
• Display glitch recovery now also works on error and boot screens
• Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

New features

• HT hotend support with automatic hotend detection
• PPS and PPA filament presets for the HT hotend
• PVA and BVOH filament presets
• Filament color support
• Tool mapping presets and Smart mapping
• Automatic Z-axis alignment on uneven bed
• Runout Reaction setting for instant or delayed runout handling (#5423)

Changes and improvements

• New versioning policy
• Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
• Reorganized Tune menu [6.9.0]
• Tool mapping is now preserved when reprinting a job [6.9.0]
• New Customize button for tweaking a loaded filament
• Stuck filament dialog now offers Ignore and Disable options [6.9.0]
• Improved Nozzle Wiper cleaning [6.10.1]
• Parking now lifts the Z axis faster [6.10.2]
• Heater selftest now lowers the bed further to leave room for hands [6.9.1]
• Chamber vents now close automatically at the end of a print [6.9.0]
• Filament sensor selftest now detects a disconnected sensor [6.9.0]
• G-code lines sent over USB/serial that are too long now show a warning
• PrusaLink file downloads now keep long file names
• Prusa Connect now shows changed chamber, fan and light values within seconds
• MMU filament menu now shows the loaded filament and its color [MMU]

Fixes

• Improved security and robustness
• Fixed unreliable homing [C1/+] [6.9.1]
• Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
• Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
• Fixed chamber temperature serial reporting format
• Fixed an extra blob of filament when resuming after a power failure [6.9.0]
• Fixed settings being lost when power was cut while they were being saved [6.10.1]
• Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
• Fixed the Not enough tools G-code check blocking prints with no way to bypass it
• Fixed a crash when the door was opened during homing
• Fixed wrong remaining time after resuming from a power failure [6.9.0]
• Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
• Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
• Fixed a crash on the print preview screen
• Fixed text overflowing on the factory reset screen
• Fixed a crash when changing Front PTFE Length [MMU]
• Fixed tool mapping being ignored when starting a print from Prusa Connect
• Display glitch recovery now also works on error and boot screens
• Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

• Dodano kontrolę obecności filamentu na początku drukowania.
• Poprawki regionalnego poziomowania stołu.
• Wyświetlanie koloru/nazwy filamentu podczas M600.
• Poprawka niepoprawnej obsługi timera bezpieczeństwa.
• Opóźnienie osi Z przy automatycznym ładowaniu.
• Zastąpienie zakodowanej na stałe wartości podnoszenia Z podczas zderzenia przez pauzę Z.
• Wysyłanie działań hosta dotyczących wyczerpania filamentu.
• Obniżenie MIN_Z_FOR_UNLOAD z 50 mm do 20 mm.
• Dodanie pozycji „załaduj filament”, jeśli automatyczne ładowanie jest wyłączone.
• Przerwanie zmiany dyszy, jeśli filament jest załadowany.
• Zmiany związane z PowerPanic.
• Zmniejszenie temperatury otoczenia przy wyłączeniu do 80°C.
• Dodano utils/build.py, aby móc skompilować firmware.
• Zmiany związane z MMU.
• Drobne poprawki.
• Zmiany wprowadzone przez społeczność.

• Dodano kontrolę obecności filamentu na początku drukowania.
• Poprawki regionalnego poziomowania stołu.
• Wyświetlanie koloru/nazwy filamentu podczas M600.
• Poprawka niepoprawnej obsługi timera bezpieczeństwa.
• Opóźnienie osi Z przy automatycznym ładowaniu.
• Zastąpienie zakodowanej na stałe wartości podnoszenia Z podczas zderzenia przez pauzę Z.
• Wysyłanie działań hosta dotyczących wyczerpania filamentu.
• Obniżenie MIN_Z_FOR_UNLOAD z 50 mm do 20 mm.
• Dodanie pozycji „załaduj filament”, jeśli automatyczne ładowanie jest wyłączone.
• Przerwanie zmiany dyszy, jeśli filament jest załadowany.
• Zmiany związane z PowerPanic.
• Zmniejszenie temperatury otoczenia przy wyłączeniu do 80°C.
• Dodano utils/build.py, aby móc skompilować firmware.
• Zmiany związane z MMU.
• Drobne poprawki.
• Zmiany wprowadzone przez społeczność.

• New features
  • HT hotend support with automatic hotend detection
  • PPS and PPA filament presets for the HT hotend
  • PVA and BVOH filament presets
  • Filament color support
  • Tool mapping presets and Smart mapping
  • Automatic Z-axis alignment on uneven bed
  • Runout Reaction setting for instant or delayed runout handling (#5423)
• Changes and improvements
  • New versioning policy
  • Bed now moves further down after finishing, pausing or stopping a print [6.9.0]
  • Reorganized Tune menu [6.9.0]
  • Tool mapping is now preserved when reprinting a job [6.9.0]
  • New Customize button for tweaking a loaded filament
  • Stuck filament dialog now offers Ignore and Disable options [6.9.0]
  • Improved Nozzle Wiper cleaning [6.10.1]
  • Parking now lifts the Z axis faster [6.10.2]
  • Heater selftest now lowers the bed further to leave room for hands [6.9.1]
  • Chamber vents now close automatically at the end of a print [6.9.0]
  • Filament sensor selftest now detects a disconnected sensor [6.9.0]
  • G-code lines sent over USB/serial that are too long now show a warning
  • PrusaLink file downloads now keep long file names
  • Prusa Connect now shows changed chamber, fan and light values within seconds
  • MMU filament menu now shows the loaded filament and its color [MMU]
• Fixes
  • Improved security and robustness
  • Fixed unreliable homing [C1/+] [6.9.1]
  • Fixed the Wi-Fi connection hanging after a communication error [6.10.2]
  • Fixed the PNG thumbnail of plain G-code files not showing in Prusa Connect
  • Fixed chamber temperature serial reporting format
  • Fixed an extra blob of filament when resuming after a power failure [6.9.0]
  • Fixed settings being lost when power was cut while they were being saved [6.10.1]
  • Fixed retract or purge running on a nozzle cooled down by the safety timer [6.9.0]
  • Fixed the Not enough tools G-code check blocking prints with no way to bypass it
  • Fixed a crash when the door was opened during homing
  • Fixed wrong remaining time after resuming from a power failure [6.9.0]
  • Fixed factory reset of the HW configuration not resetting calibrations [6.9.0]
  • Fixed M340 refusing to set the syslog host when metrics were allowed [6.9.0]
  • Fixed a crash on the print preview screen
  • Fixed text overflowing on the factory reset screen
  • Fixed a crash when changing Front PTFE Length [MMU]
  • Fixed tool mapping being ignored when starting a print from Prusa Connect
  • Display glitch recovery now also works on error and boot screens
  • Fixed not saving a crash dump on a red screen error (RSOD) [6.9.0]

• Dodano kontrolę obecności filamentu na początku drukowania.
• Poprawki regionalnego poziomowania stołu.
• Wyświetlanie koloru/nazwy filamentu podczas M600.
• Poprawka niepoprawnej obsługi timera bezpieczeństwa.
• Opóźnienie osi Z przy automatycznym ładowaniu.
• Zastąpienie zakodowanej na stałe wartości podnoszenia Z podczas zderzenia przez pauzę Z.
• Wysyłanie działań hosta dotyczących wyczerpania filamentu.
• Obniżenie MIN_Z_FOR_UNLOAD z 50 mm do 20 mm.
• Dodanie pozycji „załaduj filament”, jeśli automatyczne ładowanie jest wyłączone.
• Przerwanie zmiany dyszy, jeśli filament jest załadowany.
• Zmiany związane z PowerPanic.
• Zmniejszenie temperatury otoczenia przy wyłączeniu do 80°C.
• Dodano utils/build.py, aby móc skompilować firmware.
• Zmiany związane z MMU.
• Drobne poprawki.
• Zmiany wprowadzone przez społeczność.

• Obsługa Prusa Connect
• Własne profile druku
• Aktualizacja PrusaLink Web
• Limity czasu naświetlania
• Poprawiona obsługa pamięci USB
• Wyłączono obsługę kluczy API
• Inne ulepszenia
• Poprawki błędów
• Znane problemy

• Dodano kontrolę obecności filamentu na początku drukowania.
• Poprawki regionalnego poziomowania stołu.
• Wyświetlanie koloru/nazwy filamentu podczas M600.
• Poprawka niepoprawnej obsługi timera bezpieczeństwa.
• Opóźnienie osi Z przy automatycznym ładowaniu.
• Zastąpienie zakodowanej na stałe wartości podnoszenia Z podczas zderzenia przez pauzę Z.
• Wysyłanie działań hosta dotyczących wyczerpania filamentu.
• Obniżenie MIN_Z_FOR_UNLOAD z 50 mm do 20 mm.
• Dodanie pozycji „załaduj filament”, jeśli automatyczne ładowanie jest wyłączone.
• Przerwanie zmiany dyszy, jeśli filament jest załadowany.
• Zmiany związane z PowerPanic.
• Zmniejszenie temperatury otoczenia przy wyłączeniu do 80°C.
• Dodano utils/build.py, aby móc skompilować firmware.
• Zmiany związane z MMU.
• Drobne poprawki.
• Zmiany wprowadzone przez społeczność.

• Wydłużenie wszystkich timerów do 255 minut
• Filtrowanie IPA (nowa funkcja)
• Cykle mycia (nowa funkcja)
• Nowy algorytm podgrzewania
• Automatyczne sterowanie wentylatorami
• Opcja resetu fabrycznego
• Ulepszony Selftest
• Poprawki błędów

• Dodano kontrolę obecności filamentu na początku drukowania.
• Poprawki regionalnego poziomowania stołu.
• Wyświetlanie koloru/nazwy filamentu podczas M600.
• Poprawka niepoprawnej obsługi timera bezpieczeństwa.
• Opóźnienie osi Z przy automatycznym ładowaniu.
• Zastąpienie zakodowanej na stałe wartości podnoszenia Z podczas zderzenia przez pauzę Z.
• Wysyłanie działań hosta dotyczących wyczerpania filamentu.
• Obniżenie MIN_Z_FOR_UNLOAD z 50 mm do 20 mm.
• Dodanie pozycji „załaduj filament”, jeśli automatyczne ładowanie jest wyłączone.
• Przerwanie zmiany dyszy, jeśli filament jest załadowany.
• Zmiany związane z PowerPanic.
• Zmniejszenie temperatury otoczenia przy wyłączeniu do 80°C.
• Dodano utils/build.py, aby móc skompilować firmware.
• Zmiany związane z MMU.
• Drobne poprawki.
• Zmiany wprowadzone przez społeczność.

• Dodano kontrolę obecności filamentu na początku drukowania.
• Poprawki regionalnego poziomowania stołu.
• Wyświetlanie koloru/nazwy filamentu podczas M600.
• Poprawka niepoprawnej obsługi timera bezpieczeństwa.
• Opóźnienie osi Z przy automatycznym ładowaniu.
• Zastąpienie zakodowanej na stałe wartości podnoszenia Z podczas zderzenia przez pauzę Z.
• Wysyłanie działań hosta dotyczących wyczerpania filamentu.
• Obniżenie MIN_Z_FOR_UNLOAD z 50 mm do 20 mm.
• Dodanie pozycji „załaduj filament”, jeśli automatyczne ładowanie jest wyłączone.
• Przerwanie zmiany dyszy, jeśli filament jest załadowany.
• Zmiany związane z PowerPanic.
• Zmniejszenie temperatury otoczenia przy wyłączeniu do 80°C.
• Dodano utils/build.py, aby móc skompilować firmware.
• Zmiany związane z MMU.
• Drobne poprawki.
• Zmiany wprowadzone przez społeczność.

• Poprawiono błędy nagrzewania
• Poprawiono regulację temperatury
• Obsługa szacowanego czasu do końca wydruku
• Możliwość zmiany ustawień powiadomień dźwiękowych
• Aktualizacja sprawdzania kompletności pliku
• Poprawki G-code (M27, M110, M115)

• Poprawiono błędy nagrzewania
• Poprawiono regulację temperatury
• Obsługa szacowanego czasu do końca wydruku
• Możliwość zmiany ustawień powiadomień dźwiękowych
• Aktualizacja sprawdzania kompletności pliku
• Poprawki G-code (M27, M110, M115)

• Poprawiona kalibracja XYZ
• Efekty kalibracji XYZ są teraz widoczne w menu Wsparcie
• Poprawka Selftestu
• Poprawione rozładowywanie filamentu
• Multi Material
• Podczas zatrzymywania wydruku użytkownik jest pytany o filament do rozładowania
• Dodano G-code "T?", który wybiera używany ekstruder
• Dodano wsparcie dla MK1