LCD menu (XL Multi Tool)

Questo articolo è disponibile anche nelle seguenti lingue: 

The Original Prusa XL is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

For the versions of the XL printer with a single tool head, go to LCD menu (XL Single Tool) [Traduzione in corso].

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

If you have a Dual Toolhead printer, only two tools will appear in the menu shown below.

Menu structure

• Print
• Preheat
  • • PLA
    • PETG
    • ASA
    • PC
    • PVB
    • ABS
    • HIPS
    • PP
    • FLEX
    • PA
    • Cooldown
• Filament
  • • Load filament
    • Unload filament
    • Change filament
    • Purge filament
    • Change Filament in All Tools
      • • Tool 1 Filament
        • Tool 2 Filament
        • Tool 3 Filament
        • Tool 4 Filament
        • Tool 5 Filament
        • Carry Out the Changes
• Control
  • •  Pick/Park Tool
      • • Park Current Tool
        • Pick Tool 1
        • Pick Tool 2
        • Pick Tool 3
        • Pick Tool 4
        • Pick Tool 5
    • Move axis
      • • Move X
        • Move Y
        • Move Z
        • Move E
        • Cooldown
    • Temperature
      • • Heatbed temperature
        • Nozzle 1 temperature
        • Nozzle 2 temperature
        • Nozzle 3 temperature
        • Nozzle 4 temperature
        • Nozzle 5 temperature
        • Print fan speed
        • Cooldown
    • Autohome
    • Set ready
    • Disable motors
    • Calibrations & Tests
      • • 1 Fan Test
        • 2 Y Axis Test
        • 3 X Axis Test
        • 4 Z Alignment Calibration
        • 5 Dock Position Calibration
        • 6 Loadcell Test
        • 7 Z Axis Test
        • 8 Nozzle Heaters Test
        • 9 Filament Sensor Calibration
        • 10 Tool Offset Calibration
        • 11 Bed Heater Test
• Settings
  • • Filament Sensor
    • Fan check
    • Crash Detection
    • Tools
      • • Tool 1
          • • Nozzle Diameter
            • Dock X
            • Dock Y
            • Calibrate Dock Position
            • Calibrate Filament Sensor
            • Pickup Tool
        • Tool 2
        • Tool 3
        • Tool 4
        • Tool 5
        • Park Current Tool
    • Input Shaper
      • • X-axis filter
        • X-axis frequency
        • Y-axis filter
        • Y-axis frequency
    • User Interface
      • • Footer
        • Sort Files [Time/Name]
        • Print Progress Screen [OFF, 30 s - 200 s]
        • Menu Timeout
        • Sound Mode [Loud/Silent/Assist/Once]
        • For filament change, preheat [Nozzle/Noz&Bed]
        • RGB Status Bar
        • RGB Side Strip
        • Tool Light
    • Language & Time
      • • Language
        • Time Zone Offset
        • Time Format
    • Network
      • • Prusa Link
          • • Enabled
            • Generate Password
            • User
            • Password
        • Prusa Connect
          • • Enabled
            • Status
            • Error
            • Add printer to Connect
            • Load Settings
        • Default [Eth/Wi-fi]
        • IPv4 Address
        • MAC address
        • Metrics &Log
          • • What is this?
            • Allow [None/Only Stored/Any Host]
            • Enable Stored on Startup
            • Stored Configuration
            • Current configuration
            • Log Port
        • Ethernet
          • • Protocol
            • LAN
            • IPv4 Address
            • IPv4 Netmask
            • IPv4 Gateway
            • MAC Address
        • Wi-Fi
          • • Create Credentials
            • Load Credentials
            • Protocol
            • LAN
            • IPv4 Address
            • IPv4 Netmask
            • IPv4 Gateway
            • MAC Address
    • Hardware
      • • G-code checks
          • • Nozzle Diameter [Warn/Strict/None]
            • Printer Model [Warn/Strict/None]
            • Firmware Version [Warn/Strict/None]
            • G-code Level [Warn/Strict/None]
        • Side FSensor Remap
        • Heat Entire Bed
        • Crash Sensitivity XY
        • Filament Autoloading
    • FW update
    •  System
      • • Save Crash Dump
        • Device Hash in QR
        • Load Settings from File
        • Factory Reset
          • • Reset Settings & Calibrations
            • Hard Reset (USB with FW needed)
• Info
  • • Sensor Info
      • • Heatbreak 1Temp
        • Heatbreak 2 Temp
        • Heatbreak 3 Temp
        • Heatbreak 4 Temp
        • Heatbreak 5 Temp
        • Board Temperature
        • Bed Temperature
        • Nozzle 1 Temperature
        • Nozzle 2 Temperature
        • Nozzle 3 Temperature
        • Nozzle 4 Temperature
        • Nozzle 5 Temperature
        • Dwarf Board Temp
        • Loadcell Value
        • Tool Filament Sensor
        • Side Filament Sensor
        • Print Fan
        • Heatbreak Fan
        • Input Voltage
        • 5V Voltage
        • Sandwich 5V Current
        • XL Buddy 5V Current
    • Version info
      • • Firmware Version
        • Bootloader Version
        • Buddy Board
        • Serial Number
        • xLCD
    • Print Statistics
      • • Fail Stats
          • • Power Failures
            • Last Print Crashes on X Axis
            • Last Print Crashes on Y Axis
            • Crashes on X Axis
            • Crashes on Y Axis
        • Statistics
          • • X-axis
            • Y-axis
            • Z -axis
        • Filament
          • • Tool 1
            • Tool 2
            • Tool 3
            • Tool 4
            • Tool 5
        • Tools changed
          • • Tool 1
            • Tool 2
            • Tool 3
            • Tool 4
            • Tool 5
        • Print Time