LCD menu (MINI/MINI+)

This article is also available in following languages: 

Navigating the LCD menu is done by a single control element: a rotational knob that you press to confirm a selection. In addition, you have a Reset button which will reset the printer if pushed. The main LCD screen also displays some other information about your printer's current state.

Menu structure

• Print
• Preheat
  • • • PLA
      • PETG
      • ASA
      • PC
      • PVB
      • ABS
      • HIPS
      • PP
      • FLEX
      • PA
      • Cooldown
• Filament
  • • • Load filament
      • Unload filament
      • Change filament
      • Purge filament
• Control
  • • • Move Axis
        • • Move X
          • Move Y
          • Move Z
          • Move E
          • Cooldown
      • Temperature
        • • Nozzle
          • Heatbed
          • Print Fan
          • Cooldown
      • Auto home
      • Set ready
      • Disable Motors
      • Live Adjust Z
      • Mesh Bed leveling
      • Bed level correction
        • • Left side
          • Right side
          • Front side
          • Rear side
          • Reset
      • Calibrations & Tests
        • • Fan Test
          • XY axis Test
          • Z axis Test
          • Heater Test
          • First Layer calibration
• Settings
  • • • Filament Sensor
      • Stealth Mode
      • Fan Check
      • Input Shaper
        • • X-axis filter
          • X-axis freq.
          • Y-axis filter
          • Y-axis freuq.
          • Restore Defaults
      • User Interface
        • • Footer 
          • Sort Files [Time/Name]
          • Menu Timeout
          • Sound Mode [Silent/Assist/Once/Loud]
          • For filament change, preheat [Nozzle/Noz&Bed]
          • Sound Volume [0-11]
      • Language & Time
        • • Language
          • Time Zone Hour Offset
          • Time Zone Minute Offset
          • Time Zone Summertime
          • Time Format [24h/12h]
          • Time
      • Network
        • • Prusalink
            • • Enabled
              • Generate Password
              • User
              • Password
          • Prusa Connect
            • • Enabled
              • Status
              • Error
              • Add printer to Connect
              • Load Settings
          • Default [Wi-Fi/Eth]
          • IP
          • MAC
          • Metrics & Log 
            • • What is this?
              • Allow [None/Only Stored/Any Host]
              • Enable Stored on Startup
              • Stored Configuration
              • Current configuration
          •  Ethernet
            • Protocol
            • LAN
            • IP
            • Mask
            • GW
            • MAC
          • Wi-Fi
            • Setup Wi-Fi module
            • Create credentials
            • Load credentials
            • Protocol
            • LAN
            • IP
            • Mask
            • GW
            • MAC
      • Hardware
        • • Nozzle Diameter [0.25-1.00]
          • G-Code Checks
            • Nozzle Diameter [Warn/Strict/None]
            • Printer Mode [Warn/Strict/None]
            • Firmware Version [Warn/Strict/None]
            • G-Code Level [Warn/Strict/None]
          • Steel Sheets
      • FW update
      • System
        • • Save Crash Dump
          • Device Hash in QR
          • Load Settings from File
          • Factory reset
            • Reset Settings & Calibrations
            • Hard Reset (USB with Firmware needed)
• Info
  • • • Sensor info
        • • Filament Sens
          • M.I.N.D.A.
          • MCU Temperature
      • Version info
        • • Firmware Version
          • Bootloader Version
          • Buddy Board
      • Print Statistics
        • • Statistics
            • X Axis
            • Y Axis
            • Z Axis
            • Filament
            • Print Time