Navigating the LCD menu is done by a single control element: a rotational knob that you press to confirm a selection. In addition, you have a Reset button which will reset the printer if pushed. The main LCD screen also displays some other information about your printer's current state.
This menu structure was introduced with firmware version 4.4.0. Make sure your firmware is up to date.
Menu structure
- Preheat
-
-
- PLA
- PETG
- ASA
- PC
- PVB
- ABS
- HIPS
- PP
- FLEX
- PA
- Custom
-
- Name
- Nozzle temperature
- Nozzle Preheat Temperature
- Bed Temperature
- Is Abrasive
- Requires Filtration
- Confirm
-
- Show All
- Cooldown
-
-
- Filament
-
-
- Load filament
- Unload filament
- Change filament
- Purge filament
- Manage Filaments
-
- Loaded
-
- Name
- Visible
- Nozzle temp
- Preheat Temp
- Bed Temp
- Is Abrasive
- Requires Filtration
-
- Edit Filaments
- Reorder Filaments
- Enable Filaments
- Loaded
-
-
-
- Control
-
-
- Move Axis
-
- Move X
- Move Y
- Move Z
- Move E
- Cooldown
-
- Temperature
-
- Nozzle
- Heatbed
- Print Fan
- Cooldown
-
- Auto home
- Set ready
- Disable Motors
- Live Adjust Z
- Mesh Bed leveling
- Bed level correction
-
- Left side
- Right side
- Front side
- Rear side
- Reset
-
- Calibrations & Tests
-
- Fan Test
- XY axis Test
- Z axis Test
- Heater Test
- First Layer calibration
-
- Move Axis
-
-
- Settings
-
-
- Filament Sensor
- Stealth Mode
- Fan Check
- Verify Gcode
- Input Shaper
-
- X-axis filter
- X-axis freq.
- Y-axis filter
- Y-axis freuq.
- Restore Defaults
-
- User Interface
-
- Footer
-
- Item 1 [None/Nozzle/Bed/Filament/FSensor/Speed/X/Y/Z/Z height/Print fan/Hotend fan/Live Z/Sheets/Nozzle dia/Nozzle PMW]
- Item 2
- Item 3
- Reset
-
- Sort Files [Time/Name]
- Menu Timeout
- Sound Mode [Silent/Assist/Once/Loud]
- For filament change, preheat [Nozzle/Noz&Bed]
- Sound Volume [Off/0-11]
- Footer
-
- Language & Time
-
- Language
- Time Zone Hour Offset
- Time Zone Minute Offset
- Time Zone Summertime
- Time Format [24h/12h]
- Time
-
- Network
-
- Active Interface [Eth/Wi-Fi]
- Network Status
-
- Status
- IP
- Gateway
- MAC
- Hostname
- DNS
- Ping | Loss
- Gateway
- DNS
-
- Wi-Fi
-
- Status
- DDID
- Wi-Fi Wizard
- Protocol
- LAN
- IP
- Mask
- Gateway
- Hostname
- MAC
-
- Ethernet
-
- Protocol
- LAN
- IP
- Mask
- Gateway
- Hostname
- MAC
-
- Prusa Connect
-
- Enabled
- Status
- Error
- Hostname
- Add Printer to Connect
- Load Settings
-
- Prusalink
-
- Enabled
- User
- Password
- IP
- Hostname
- Generate password
-
- Metrics & Log
-
- What is this?
- Enable Metrics
- Host
- Metrics Port
- Syslog Port
- MAC
- Metrics List
-
-
- Hardware
-
- Print head
-
- Nozzle Diameter
- Nozzle hardened
- Nozzle High-flow
-
- Steel Sheets
- G-code checks
-
- Nozzle [Warn/Strict/None]
- Printer Model [Warn/Strict/None]
- Firmware Version [Warn/Strict/None]
- G-code Level [Warn/Strict/None]
-
- Print head
-
- FW update
- System
-
- Save Crash Dump
- Save Logs To File
- Device Hash in QR
- Load Settings from File
- Factory Reset
-
- Reset Settings & Calibrations
- Hard Reset (USB with FW needed)
-
-
-
-
- Info
-
-
- Network Status
-
- Status
- IP
- Gateway
- MAC
- Hostname
- DNS
- PING | Loss
- Gateway
- DNS
-
- Sensor info
-
- Filament Sens
- M.I.N.D.A.
- MCU Temperature
-
- Version info
-
- Firmware Version
- Bootloader Version
- Buddy Board
-
- Print Statistics
-
- Statistics
-
- X Axis
- Y Axis
- Z Axis
- Filament
- Print Time
-
- Statistics
-
- Network Status
-
-
Was this article helpful?
This action is available only to registered users. Please log-in.
3 comments
Yes, it should be peeled off.
Can you please add the structure of the menu while the printer is printing such as the Tune menu, etc?
I am totally blind and this guide is very helpful.