LCD メニュー (XLシングルツール)

This article is also available in following languages: 

Original Prusa XLはカラー液晶画面を搭載しており、特にGコードサムネイルとQRコードに対応しています。

複数のツールヘッドを備えたXLプリンターのバージョンについては、LCD メニュー (XLマルチツール)を参照してください。

メイン画面のフッターを編集して、メインページに表示したい機能を表示することができます。

常に最新の最新ファームウェアを持っていることを確認してください。

Menu structure

• Print
• Preheat
  • • PLA
    • PETG
    • ASA
    • PC
    • PVB
    • ABS
    • HIPS
    • PP
    • FLEX
    • PA
    • Cooldown
• Filament
  • • Load filament
    • Unload filament
    • Change filament
    • Purge filament
• Control
  • • Move axis
      • • Move X
        • Move Y
        • Move Z
        • Move E
        • Cooldown
    • Temperature
      • • Heatbed temperature
        • Nozzle temperature
        • Print fan speed
        • Cooldown
    • Autohome
    • Set Ready
    • Disable motors
    • Enclosure
    • Calibrations & Tests
      • • 1 Fan Test
        • 2 Y Axis Test
        • 3 X Axis Test
        • 4 Z Alignment Calibration
        • 5 Loadcell Test
        • 6 Nozzle Diameter Confirmation
        • 7 Z Axis Test
        • 8 Heater Test
        • 9 Filament Sensor Calibration
        • 10 Phase Stepping Calibration
• Settings
  • • Filament Sensor
      • Side Filament Sensor 
      • Toolhead Filament Sensor
      • Restore Defaults
    • Stuck Filament Detection
    • Stealth Mode
    • Fan check
    • Crash Detection
    • Input Shaper
      • • X-axis filter
        • X-axis frequency
        • Y-axis filter
        • Y-axis frequency
        • Restore Defaults
    • User Interface
      • • Footer
        • Sort Files [Time/Name]
        • Print Progress Screen [OFF, 30 s - 200 s]
        • Menu Timeout
        • Sound Mode [Loud/Silent/Assist/Once]
        • For filament change, preheat [Nozzle/Noz&Bed]
        • RGB Status Bar
        • RGB Side Strip
        • RGB Side Strip Dimming
        • Touch 
        • Touch Sig Workaround
    • Language and Time
      • • Language
        • Time Zone Hour Offset
        • Time Zone Minute Offset
        • Time Zone Summertime
        • Time Format
    • Network
      • • Prusa Link
          • • Enabled
            • Generate Password
            • User
            • Password
        • Prusa Connect
          • • Enabled
            • Status
            • Error
            • Add printer to Connect
            • Load Settings
        • Default [Eth/Wi-fi]
        • IPv4 Address
        • Hostname
        • MAC address
        • Metrics &Log
          • • What is this?
            • Allow [None/Only Stored/Any Host]
            • Enable Stored on Startup
            • Stored Configuration
            • Current configuration
        • Ethernet
          • • Protocol
            • LAN
            • IPv4 Address
            • IPv4 Netmask
            • IPv4 Gateway
            • Hostname
            • MAC Address
        • Wi-Fi
          • • Status
            • Create Credentials
            • Load Credentials
            • Protocol
            • LAN
            • IPv4 Address
            • IPv4 Netmask
            • IPv4 Gateway
            • Hostname
            • MAC Address
    • Hardware
      • • Nozzle Diameter [0.25mm-1.00mm]
        • G-code checks
          • • Nozzle Diameter [Warn/Strict/None]
            • Printer Model [Warn/Strict/None]
            • Firmware Version [Warn/Strict/None]
            • G-code Level [Warn/Strict/None]
        • Side FSensor Remap
        • Heat Entire Bed
        • Crash Sensitivity XY
        • Phase Stepping
    • FW update
    • System
      • • Save Crash Dump
        • Device Hash in QR
        • Load Settings from File
        • Factory Reset
          • • Reset Settings & Calibrations
            • Hard Reset (USB with FW needed)
• Info
  • • Sensor Info
      • • Heatbreak Temp
        • Board Temperature
        • MCU Temperature
        • Bed Temperature
        • Nozzle Temperature
        • Dwarf Board Temp
        • Dwarf MCU Temp
        • MBed MCU Temp
        • Loadcell Value
        • Tool Filament Sensor
        • Side Filament Sensor
        • Print Fan
        • Heatbreak Fan
        • Input Voltage
        • 5V Voltage
        • Sandwich 5V Current
        • XL Buddy 5V Current
    • Version info
      • • Firmware Version
        • Bootloader Version
        • Buddy Board
        • Serial Number
        • xLCD
    • Print Statistics
      • • Fail Stats
          • • Power Failures
            • Last Print Crashes on X Axis
            • Last Print Crashes on Y Axis
            • Crashes on X Axis
            • Crashes on Y Axis
        • Statistics
          • • X-axis
            • Y-axis
            • Z -axis
            • Filament
            • Print Time