Passo 1 Get the necessary tools
⬢Needle-nose pliers
⬢2.5 mm Allen key
IT
Login- English
6. LCD assembly
Menu
- Kit da assemblare Original Prusa i3 MK2
- 1. Introduction
- 2. Y-axis assembly
- 3. X-axis assembly
- 4. Z-axis assembly
- 5. Extruder Assembly
- 6. LCD assembly
- 1. Get the necessary tools
- 2. 3D printed parts
- 3. Preparing the LCD support for assembly
- 4. Adjusting the LCD-support
- 5. Assembling the LCD-cover
- 6. Securing the LCD controller
- 7. Assembling the LCD knob
- 8. Plug in the cables
- 9. Secure the LCD display onto the printer
- 10. Secure the LCD assembly
- 11. Guiding the LCD cables
- 12. All done!
- 7. PSU & Heatbed assembly
- 8. Electronics assembly
- 9. Preflight check
6. LCD assembly
Rilevante per:
Ultimo aggiornamento 3 years ago Difficoltà
Moderato Passi
12 Lingue disponibili
Passo 2 3D printed parts
⬢LCD-cover
⬢LCD-knob
⬢LCD-support
⬢LCD-cable-clip
Passo 3 Preparing the LCD support for assembly
⬢Prepare the LCD controller and LCD-support printed parts as shown in the picture.
Ensure the correct orientation of parts and the LCD controller.
⬢Slide the LCD-support parts on the LCD-controller.
The exact position will be adjusted in the next step, no need to worry at this moment.
You can now remove the protective foil from the LCD panel.
Cables are plugged to the LCD from the factory, but you can disconnect them.
Passo 4 Adjusting the LCD-support
⬢Adjust the LCD-support parts as shown in the picture.
⬢LCD-support parts must face directly into the cutouts in the LCD-cover.
Passo 5 Assembling the LCD-cover
⬢Press the LCD controller with the LCD-support into the LCD-cover as shown in the picture.
⬢Press it as deep as possible.
⬢The LCD controller must click under support in the center of the LCD-cover.
Passo 6 Securing the LCD controller
⬢M3x10 screws (2 pcs)
⬢Using the 2.5mm hex spanner, secure the LCD controller in place.
Passo 7 Assembling the LCD knob
⬢Assemble the LCD-knob part as shown in the picture.
Passo 8 Plug in the cables
⬢Plug in the cables as shown in the picture.
⬢Cable with 1 stripe has to be plugged in the connector labeled with EXP1.
⬢Cable with 2 stripes has to be plugged in the connector labeled with EXP2.
Passo 9 Secure the LCD display onto the printer
⬢Press the LCD assembly onto the front side of the Y-axis.
Best way is to press the LCD assembly on the top threaded rod first and then on the bottom.
⬢Guide the LCD cables in between threaded rods as in the picture.
Passo 10 Secure the LCD assembly
⬢Use the zipties to anchor the LCD assembly to the threaded rods.
Passo 11 Guiding the LCD cables
⬢Guide the LCD cables using LCD-clips as seen in the picture.
⬢Reverse direction of each of the clip, to prevent side movement of the cables.
Passo 12 All done!
⬢Congratulations! You've attached the LCD to the Prusa i3 3D printer!
⬢You can continue by assembling the PSU and the heatbed in the next chapter - 7. PSU & Heatbed assembly [Traduzione in corso].
Questa guida è stata utile?
Commenti
Hai ancora delle domande?
Se hai una domanda su qualcosa che non è trattato qui, dai un'occhiata alle nostre risorse aggiuntive.
E se questo non dovesse funzionare, è possibile inviare una richiesta a [email protected] o tramite il pulsante qui sotto.