1. Tools necessary for this chapter

Prusa INDX Umrüstsatz für den Prusa CORE One/+ (1.00)

• 1. Introduction
• 2. Printer preparation & disassembly
• 3. Z-axis upgrade
• 4. INDX Toolhead & Side filament sensors
• 5. Spoolholders & Tool dock assembly [Übersetzung in Arbeit]
  1. Tools necessary for this chapter
  2. Abnehmen der Seitenabdeckung - rechts
  3. Side handle: parts preparation
  4. Installing the side handle
  5. Nozzle cleaner: parts preparation I.
  6. Nozzle cleaner: parts preparation II.
  7. Zusammenbau des Wiper-lock
  8. Befestigen des Wiper-lock
  9. Montieren des Wiper-adjuster
  10. Inserting the wiper blocks
  11. Dock fan cable: parts preparation
  12. Attaching the dock fan cable
  13. Leading the dock fan cable I.
  14. Verlegung Dock-Lüfter-Kabel
  15. Befestigung der Kabelbinder
  16. Securing the zip ties II.
  17. Electronics covers: parts preparation
  18. Befestigen der Kabel
  19. Verdrahtung prüfen
  20. Covering the xBuddy box
  21. Installing the rear cover
  22. Montage der Seitenwand: Vorbereitung der Teile
  23. Mounting the right side panel
  24. Bottom puck holders: parts preparation
  25. Assembling the bottom puck holders
  26. Removing the screws - left
  27. Mounting the bottom puck holders - left
  28. Befestigen des vorderen Puck-holder-bottom – links I.
  29. Befestigen des vorderen Puck-holder-bottom – links II.
  30. Befestigen des hinteren Puck-holder-bottom – links I.
  31. Befestigen des hinteren Puck-holder-bottom – links II.
  32. Top puck holders: parts preparation
  33. Assembling the puck holder top
  34. Entfernen der oberen Nylonnieten - links
  35. Mounting the front puck holder top - left
  36. Securing the front puck holder top - left
  37. Mounting the rear puck holder top - left
  38. Securing the rear puck holder top - left
  39. Removing the screws - right
  40. Mounting the bottom puck holders - right
  41. Securing the front Puck-holder bottom - right I.
  42. Securing the front Puck-holder bottom - right II.
  43. Securing the rear Puck-holder bottom - right I.
  44. Securing the rear Puck-holder bottom - right II.
  45. Kippen des Druckers
  46. Finishing the rear puck holder bottom - left I.
  47. Finishing the rear puck holder bottom - left II.
  48. Finishing the front puck holder bottom - left I.
  49. Finishing the front puck holder bottom - left II.
  50. Finishing the rear puck holder bottom - right I.
  51. Finishing the rear puck holder bottom - right II.
  52. Finishing the front puck holder bottom - right I.
  53. Finishing the front puck holder bottom - right II.
  54. Mounting the front puck holder top - right
  55. Securing the front puck holder top - right
  56. Mounting the rear puck holder top - right
  57. Securing the rear puck holder top - right
  58. Dock fan: parts preparation
  59. Assembling the dock fan
  60. Anbringen der Dock-Fan-Splitter-Platine
  61. Attaching the dock fan
  62. Securing the dock fan
  63. Haribo Zeit!
  64. Werkzeugdock: Vorbereitung der Teile
  65. Assembling the tool holder
  66. Installing the tool holders
  67. Nozzle seal holder: parts preparation
  68. Assembling the nozzle seal
  69. Zusammenbau des Düsendichtungshalters
  70. Installing the nozzle parking plates
  71. Ventilation lever: parts preparation
  72. Assembling the ventilation lever
  73. Top cover: parts preparation I.
  74. Top cover: parts preparation II.
  75. Attaching the hinge covers
  76. Anbringen des Gitters
  77. Attaching the left cover lock
  78. Attaching the right cover lock
  79. Top cover back: parts preparation
  80. Attaching the top cover back
  81. Attaching the hinge base - left
  82. Attaching the hinge base - right
  83. Attaching the top cover I.
  84. Attaching the top cover II.
  85. INDX Nozzle tool: parts preparation
  86. Anbringen des Werkzeugdocks
  87. Befestigen des Werkzeugdocks
  88. Attaching the LED panel
  89. Optional: Installing the Buddy3D Camera
  90. Connecting the INDX Nozzle tools (positions 1–4)
  91. Docking the tools (positions 1–4)
  92. Connecting the INDX Nozzle tools (positions 5–8)
  93. Docking the tools (positions 5–8)
  94. Überprüfen der Schläuche
  95. Offset sensor cover: parts preparation
  96. Covering the offset sensor
  97. Door panel: parts preparation
  98. Mounting the door panel
  99. Anbringen der Aufkleber: Vorbereitung der Teile
  100. Anbringen des Upgrade-Aufklebers
  101. Anbringen des SN-Aufklebers
  102. Haribo Zeit!
  103. Das war's!
• 6. Preflight check