EN
  • Čeština
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

How to change the belt (XL)

Menu

How to change the belt (XL)

How to change the belt (XL)
Relevant for:
Last updated a month ago
How to change the belt (XL)
 Difficulty
Moderate
 Steps
56
 Available languages
CSPLDEITFR
Introduction
Introduction
Introduction
This guide will take you through the installation of both XL belts on the Original Prusa XL.
The following instructions are compatible with all Original Prusa XL versions.
All necessary parts are available in our eshop prusa3d.com.
Note that you have to be logged in to have access to the spare parts section.
This manual is compatible with the Original Prusa XL Enclosure.
This manual is compatible with all Original Prusa XL printers.
Tools necessary for this manual
Tools necessary for this manual
Tools necessary for this manual
For the following manual, please prepare:
Torx T10 screwdriver
2.5mm Allen key
A cardboard box for use as heatbed protection during the assembly. Hint: use the Nextruder box.
Protecting the heatbed
Protecting the heatbed
Before you proceed, it is recommended to protect the heatbed.
Make sure the heatbed is cooled down to ambient temperature. Place the empty cardboard box approximately to the front center part of the heatbed.
Manipulating with the printer
Manipulating with the printer
Manipulating with the printer
Never manipulate the printer by using the spoolholders or the upper metal flanges. You can damage the LED lights hidden inside.
When assembling, handle the base using the extrusions.
Printer unpluging
Printer unpluging
Turn the power switch OFF (symbol "O").
From the rear side of the printer, unplug the PSU cable.
Rotating the wifi antenna
Rotating the wifi antenna
Rotating the wifi antenna
Wi-Fi antenna on the back of the printer:
For the easiest installation, rotate the antenna downwards.
Wi-Fi antenna on the side of the printer:
For the easiest installation, rotate the antenna downwards.
Optional: Cables disconnecting
Optional: Cables disconnecting
Optional: Cables disconnecting
The next steps are for users who have an Original Prusa XL Enclosure add-on, otherwise skip to the Belt release
Disconnect the FAN and LED cables from the board by pressing the safety latch.
Unplug the PE faston from the connection box.
Optional: Front side releasing
Optional: Front side releasing
Optional: Front side releasing
From the front side of the enclosure:
Open the lid.
Remove the M4x8r screw using a 2.5mm Allen key.
Remove the M4x8r screw using a 2.5mm Allen key.
Optional: Rear side releasing
Optional: Rear side releasing
Optional: Rear side releasing
From the rear side of the printer:
Remove the M4x8r screw using a 2.5mm Allen key.
Remove the M4x8r screw using a 2.5mm Allen key.
Optional: Enclosure removing
Optional: Enclosure removing
Optional: Enclosure removing
Optional: Enclosure removing
Grasp the Enclosure on the front where is the support plate.
Grasp the Enclosure on the back of where is the filtration cover.
1. Push the enclosure to the back of the printer.
2. Remove the Enclosure from the printer and place it on a flat surface.
Belt releasing
Belt releasing
Belt releasing
Belt releasing
On the front side of the printer:
Using a 2.5mm Allen key, release the M3 screw holding the left CoreXY tensioner. Do not remove the screw completely.
Using a 2.5mm Allen key, release the M3 screw holding the right CoreXY tensioner. Do not remove the screw completely.
Gently tension the belt with your finger. If the belt has a similar degree of looseness as shown in the picture, proceed to the next step.
CAUTION: Lubricant Handling
CAUTION: Lubricant Handling
CAUTION: Lubricant Handling
CAUTION: Avoid direct skin contact with the lubricant used for the linear rails in this printer. If a contact occurs, wash your hands immediately. Especially before eating, drinking, or touching your face.
Lubricant accumulates mainly in the linear rail channels on the linear sides.
X-carraige cover removing
X-carraige cover removing
Remove the X-carriage cover. Don't throw the part away!
The cover snaps onto the X-carriage. It is easily removable by hand.
Belt clamps removing
Belt clamps removing
Belt clamps removing
Belt clamps removing
The color of the belt-clamps may be different depending on if you have an Original Prusa XL Enclosure. The procedure is the same, please continue.
Using the T10 Torx screwdriver, remove two M3x12rT screws holding the lower belt-clamp. Remove the belt-clamp. Do not throw the parts away!
Using the T10 Torx screwdriver, remove two M3x12rT screws holding the upper belt-clamp. Remove the belt-clamp. Do not throw the parts away!
With the belt-clamps removed, proceed to the next step.
Belts removing
Belts removing
Belts removing
Grasp the bottom belt on the left side of the CoreXY and pull the belt out of the printer.
Grasp the upper belt on the right side of the CoreXY and pull the belt out of the printer.
Throw old belts away!
Optional: Connection box removing
Optional: Connection box removing
Optional: Connection box removing
On the rear side of the printer:
If you don't have the Original Prusa XL Enclosure, please jump to CoreXY releasing
Remove two M3x10rT screws using a T10 Torx screwdriver. Don't throw the parts away!
Leave the connection box hanging freely on the cables.
Remove the remaining M3x10rT screw using a T10 Torx screwdriver. Don't throw the parts away!
Remove the fixing bracket rear left. Don't throw the parts away!
Optional:  Rear right releasing
Optional:  Rear right releasing
Remove two M3x8bT screws using a T10 Torx screwdriver. Don't throw the parts away!
Remove the fixing bracket rear left. Don't throw the parts away!
Remove the M3x6bT using a T10 Torx screwdriver. Don't throw the parts away!
From now on, we will demonstrate belt replacement on the printer without the Nextruders for better visibility. Please note, do not remove the Nextruders from your printer. The printer in the pictures will be shown without Nextruders for improved visualization for the customers.
Continue to the step CoreXY cover removing
CoreXY cover releasing
CoreXY cover releasing
CoreXY cover releasing
From now on, we will demonstrate belt replacement on the printer without the Nextruders for better visibility. Please note, do not remove the Nextruders from your printer. The printer in the pictures will be shown without Nextruders for improved visualization for the customers.
Using the T10 Torx screwdriver, remove four M3x6bT screws holding the CoreXY cover. Do not throw the screws away!
Using the T10 Torx screwdriver, remove two M3x6bT screws holding the CoreXY cover. Do not throw the screws away!
CoreXY cover removing
CoreXY cover removing
CoreXY cover removing
CoreXY cover removing
On the inner side of the CoreXY cover, unplug the PE connector.
Leave the PE connector free.
Gently remove the CoreXY cover from the printer. Do not throw the part away!
Belts attaching: parts preparation
Belts attaching: parts preparation
Belts attaching: parts preparation
The color of the belt-clamps may be different depending on if you have an Original Prusa XL Enclosure. The procedure is the same, please continue.
For the following steps, please prepare:
New XY belts (2x)
XL-belt-clamp (2x) removed in previous steps
M3x12rT screws (4x) removed in previous steps
Lower belt attaching: right front side
Lower belt attaching: right front side
Lower belt attaching: right front side
From the front side of the printer:
Take one of the belts.
Insert the one end of the belt into the front lower section of the Y-carriage-right-base.
The belt has to be facing toward the printer with the teeth showing (not the smooth side of the belt).
Double check, that you have the teeth showing side facing towards the machine.
On the inner side of the Y-carriage-right-base pull the the belt.
Don't pull the belt too much, it can fall out from the Y-carriage-right-base and the whole process of the belt attaching has to be repeated from the start.
Lower belt attaching: motor pulley belt securing
Lower belt attaching: motor pulley belt securing
Lower belt attaching: motor pulley belt securing
From the front side of the printer:
Using a shorter side of the 2.5 mm Allen key, pull gently the belt to create larger loop.
Attach the loop on the motor pulley.
Pull the belt to secure its position on the pulley.
Lower belt attaching: left side
Lower belt attaching: left side
Lower belt attaching: left side
Lower belt attaching: left side
When you pull on the belt you will feel more resistance from the XY motor, that's perfectly fine.
Pull the belt some more and guide it behind the Y-carriage-left-base.
Wrap the belt around the pulley on the front left side.
Wrap the belt around the pulley in the Y-carriage-left-base.
Lower belt attaching: belt clamp
Lower belt attaching: belt clamp
Lower belt attaching: belt clamp
The color of the belt-clamps may be different depending on if you have an Original Prusa XL Enclosure. The procedure is the same, please continue.
This image has been taken outside the printer on a white background for better visibility and definition. Follow this step on your printer.
Prepare one belt-clamp facing with the holes for the screws facing up.
Attach the left end of the belt to the belt-clamp. The end of the belt must be on half of the belt-clamp.
Attach the right end of the belt to the belt-clamp. The end of the belt must be on half of the belt-clamp.
The belt-clamp with the belts will be turned by 180°and attached to the X-carriage.
Lower belt attaching: belt clamp securing
Lower belt attaching: belt clamp securing
Lower belt attaching: belt clamp securing
Turn the prepared belt-clamp by 180° and attach the belt-clamp with the belts on the X-carriage.
Check the belts if they are in their position. If not repair the position by the previous step.
Insert two M3x12rT screws and secure them using a T10 Torx screwdriver.
Well done! One of the belts is fastened. Let's try the second one.
Upper belt attaching: left front side
Upper belt attaching: left front side
Upper belt attaching: left front side
From the front side of the printer:
Take the second belt.
Insert the one end of the belt into the front upper section of the Y-carriage-left-base.
The belt has to be facing toward the printer with the teeth showing (not the smooth side of the belt).
Double check, that you have the teeth showing side facing towards the machine.
On the inner side of the Y-carriage-left-base pull the the belt.
Don't pull the belt too much, it can fall out from the Y-carriage-left-base and the whole process of the belt attaching has to be repeated from the start.
Upper belt attaching: right rear side
Upper belt attaching: right rear side
Upper belt attaching: right rear side
Upper belt attaching: right rear side
Hint: For the simplest possible assembly, remove the fifth Nextruder (for Five-head users only) and place it on top of the box on the heating heatbed.
Pull the belt more and insert it behind the upper pulleys.
Pull the belt, which is now inserted through the upper pulleys.
From the rear side of the printer:
Insert the 2.5 mm Allen key through the hole to create a loop on the belt.
When the loop is created, you can remove the Allen key. Do not pull the belt!
Proceed to the next step.
Upper belt attaching: motor pulley belt securing
Upper belt attaching: motor pulley belt securing
Upper belt attaching: motor pulley belt securing
From the front side of the printer:
Using a shorter side of the 2.5 mm Allen key, pull gently the belt to create larger loop.
Attach the loop on the motor pulley.
Pull the belt to secure its position on the pulley.
Upper belt attaching: right side
Upper belt attaching: right side
Upper belt attaching: right side
Upper belt attaching: right side
When you pull on the belt you will feel more resistance from the XY motor, that's perfectly fine.
Pull more the belt and stretch the belt behind the Y-carriage-right-base.
Pull the belt around the pulley on the right front side.
Pull the belt around the pulley in the Y-carriage-right-base.
Upper belt attaching: belt clamp
Upper belt attaching: belt clamp
Upper belt attaching: belt clamp
The color of the belt-clamps may be different depending on if you have an Original Prusa XL Enclosure. The procedure is the same, please continue.
This image has been taken outside the printer on a white background for better visibility and definition. Follow this step on your printer.
Prepare one belt-clamp facing with the holes for the screws facing down.
Attach the right end of the belt to the belt-clamp. The end of the belt must be on half of the belt-clamp.
Attach the left end of the belt to the belt-clamp. The end of the belt must be on half of the belt-clamp.
The belt-clamp with the belts will be turned by 180°and attached to the X-carriage.
Lover belt attaching: belt clamp securing
Lover belt attaching: belt clamp securing
Lover belt attaching: belt clamp securing
Turn the prepared belt-clamp by 180° and attach the belt-clamp with the belts on the X-carriage.
Check the belts if they are in their position. If not repair the position by the previous step.
Insert two M3x12rT screws and secure them using a T10 Torx screwdriver.
Well done! Both of the belts are fastened.
Belt tensioning
Belt tensioning
Belt tensioning
On the front side of the printer:
Using a 2.5mm Allen key, slightly tighten the M3 screw holding the left CoreXY tensioner.
Using a 2.5mm Allen key, slightly tighten the M3 screw holding the right CoreXY tensioner.
Do not fully tension the belt, proceed to the next step, where is a video about the adjusting of the belts tension.
On the Original Prusa XL, adjusting the belt to the optimal tension is crucial to achieving good quality on the prints. A loose belt can cause Layer shifting, Ghosting, or other print abnormalities, like getting an irregular shape instead of a perfect circle. An over-tightened belt can cause an irregular movement in the X and Y axes.
We have our own belt tuner. The application determines the belt tension by measuring the frequency of the vibration generated by strumming it. Follow the instructions in the video below to adjust the belt.
CoreXY cover attaching
CoreXY cover attaching
CoreXY cover attaching
Gently attach the CoreXY cover on the back of the CoreXY.
On the inner side of the CoreXY cover, connect the PE connector.
Optional: Rear left securing
Optional: Rear left securing
Optional: Rear left securing
Turn the printer so the rear side is facing you.
Attach the fixing bracket rear left.
Secure the fixing bracket rear left with the M3x10rT screw.
Gently attach the XL enclosure board assembly. Don't pinch any cable!
Secure the XL enclosure board assembly with two M3x10rT screws.
Optional: Rear right securing
Optional: Rear right securing
Attach the fixing bracket rear left.
Secure the fixing bracket rear left with two M3x10rT screws.
Secure the M3x6bT screw using a T10 Torx screwdriver.
CoreXY cover securing
CoreXY cover securing
CoreXY cover securing
Insert four M3x6bT screws and tighten them using a T10 Torx screwdriver.
Insert two M3x6bT screws and tighten them using a T10 Torx screwdriver.
If you have an Original Prusa XL Enclosure, please proceed to the next step. Otherwise proceed to the Installing the Wi-Fi antenna.
Optional: Enclosure preparing
Optional: Enclosure preparing
Optional: Enclosure preparing
On the assembled Enclosure, open the lid.
Grasp the Enclosure on the front where is the support plate.
Grasp the Enclosure on the back of where is the filtration cover.
Optional: Enclosure attaching
Optional: Enclosure attaching
Optional: Enclosure attaching
For this step, call somebody to help you attach the enclosure to the printer.
Don't pinch any Enclosure cable. Watch out for cables!
Carefully attach the enclosure to the printer in three steps:
1. Place the enclosure on the printer.
2. Push the enclosure to the front of the printer.
3. Push the enclosure to the back of the printer.
Align the holes for the screws.
Optional: Front side securing
Optional: Front side securing
Optional: Front side securing
From the front side of the enclosure:
Secure the left bottom corner with an M4x8r screw to the fixing-bracket-front-left using a 2.5mm Allen key.
Secure the right bottom corner with an M4x8r screw to the fixing-bracket-front-right using a 2.5mm Allen key.
Close the lid. This prevents the lid from closing by gravity during handling.
Optional: Rear side securing
Optional: Rear side securing
Optional: Rear side securing
From the rear side of the printer:
Secure the left bottom corner with an M4x8r screw to the fixing-bracket-back-right using a 2.5mm Allen key.
Secure the left bottom corner with an M4x8r screw to the fixing-bracket-back-left using a 2.5mm Allen key.
Optional: Enclosure cables connecting
Optional: Enclosure cables connecting
Optional: Enclosure cables connecting
Attach the PE faston to the connection box.
Fully secure the PE cable to the XL Enclosure board cover.
Take the LED cable (5 wires) and connect the end of the cable to the left connector on the FDM XL Enclosure splitter.
Take the fan cable (4 wires) and connect the end of the cable to the right connector on the FDM XL Enclosure splitter.
Rotating the Wi-Fi antenna
Rotating the Wi-Fi antenna
Rotating the Wi-Fi antenna
Wi-Fi antenna on the back of the printer:
Turn the back antenna upwards.
Wi-Fi antenna on the side of the printer:
Turn the side antenna upwards.
Printer connecting
Printer connecting
Turn the power switch ON (symbol "I").
From the rear side of the printer, plug the PSU cable.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us