1. Tools necessary for this chapter
Step 1 of 83 (Chapter 5 of 10)
Contents
Comments
⬢For this chapter, please prepare:
⬢Needle-nose pliers
⬢2.0mm Allen key
⬢2.5mm Allen key
⬢T10 torx key / T10 torxy screwdriver
Contents
Prusa CORE One+ kit assembly (1.02)
- 1. Introduction
- 2. Base assembly
- 3. Back assembly
- 4. Heatbed assembly
- 5. CoreXY assembly
- Tools necessary for this chapter
- Rod holders: parts preparation
- Assembling the rod holders
- Preparing the front rod holders
- Installing the front rod holders
- XY carriage: parts preparation
- Assembling the XY-carriages
- Assembling the linear holder left
- Assembling the linear holder right
- Attaching the linear holder assemblies
- Smooth rods INFO
- Mounting the smooth rods
- Securing the rear rod holders
- Securing the front rod holders
- Motor mounts: parts preparation
- Motor mounts: part preparation
- Assembling the XY-motor-mount-right I.
- Assembling the XY-motor-mount-right II.
- Assembling the XY-motor-mount-left I.
- Assembling the XY-motor-mount-left II.
- Belt tensioners: parts preparation I.
- Belt tensioners: parts preparation II.
- Preparing the tensioner pulleys
- Assembling the belt tensioner left I.
- Assembling the belt tensioner left II.
- Assembling the belt tensioner right
- Installing the belt tensioners: parts preparation
- Installing the motor mount left
- Installing the motor mount right
- Installing the belt-tensioner-left
- Installing the belt-tensioner-right
- Linear rail: parts preparation
- Attaching the linear rail
- Securing the linear rail
- Installing the linear rail: parts preparation
- Installing the linear rail assembly
- Linear rail: removing the safety pins
- Bed-stop: parts preparation
- Assembling the bed-stop
- Mounting the bed-stop
- X&Y motors: parts preparation
- Installing the X-axis pulley
- Installing the Y-axis pulley
- XY belts: parts preparation
- XY belts INFO
- Y belt guiding: Y motor pulley
- Securing the Y-axis motor
- Y belt guiding: Y motor mount
- Y belt guiding: belt tensioner
- Y belt guiding: X motor mount
- Y belt guiding: securing the belt
- X belt guiding: X motor pulley
- Securing the X-axis motor
- Y belt guiding: X motor mount
- X belt guiding: belt tensioner
- X belt guiding: Y motor mount
- X belt guiding: securing the belt
- Checking the belt guidance
- Bowden guide: parts preparation
- Securing the Nextruder holder
- Securing the Y motor cable
- Securing the X motor cable
- Installing the bowden guide
- White LED strip: parts preparation
- Sticking the White LED strip
- Installing the white LED assembly
- Door sensor & White LED strip: parts preparation
- Inserting the zip ties
- Installing the door sensor
- Securing the door sensor cable
- Guiding the cables: LED and door sensor
- Buddy3D Camera Note
- Smooth rods: parts preparation
- Installing the CoreXY assembly
- Securing the smooth rods
- Aligning the linear rail
- Guiding the corexy cables
- Guiding the cooling fan cables
- Fixing the bed-stop
- Connecting the cooling fans cables
- Connecting the corexy cables
- Haribo time
- Done
- 6. Nextruder assembly
- 7. Bodywork & Electronics
- 8. Trim, Door & xLCD
- 9. Calibration & First run
- Manual changelog
Look out for comments when screwing your motors in. Sanding off some paint seems to help with issues printing large pieces and is easiest done now.
Things you should pay attention to to waste less time:
- The motors you will install look the same, but have different length cables. If you use the wrong ones, you will only notice in the last step of the chapter. (40mins wasted)
- I re-did belt tensionning after reading the comments. read them first. (30 mins wasted)