Como reemplazar un ventilador del fusor (MK4 / MK3.9)

Relevante para :

MK4 MK3.9

Ultima actualización 7 months ago

Dificultad

Fácil

Pasos

Idiomas disponibles

Paso 1 Introducción

⬢This guide will take you through the Hotend fan replacement on your Original Prusa MK4 or MK3.9.

⬢Todas las piezas necesarias están disponibles en nuestra tienda prusa3d.com.

Note that you have to be logged in to have access to the spare parts section.

Paso 2 Herramientas necesarias para este capitulo

⬢Para este capítulo, prepara por favor:

⬢Llave Allen de 2.5mm

Paso 3 Preparation

⬢Before you start, make sure the extruder on your printer is in the middle of both the X and Z axes.

⬢Power off your printer and disconnect it from the power.

Paso 4 Disconnecting the cables

⬢Remove the loveboard cover on the extruder by lifting it up.

⬢Disconnect the print fan, heater thermistor and heater cables.

Note there is a small safety latch on each connector, which must be pushed in, while you pull the connector out, in order to disconnect it.

Paso 5 Removing the cables

⬢Open up the print fan.

⬢Remove the hotend thermistor and heater cables from the cable groove in the x-carriage.

⬢Disconnect the hotend fan cable and pull it out of the cable groove.

⬢Remove the two M3x18 screws holding the hotend fan and remove the fan.

Paso 6 Preparación de las piezas del ventilador del hotend

⬢Para los siguientes pasos, por favor prepara:

⬢Ventilador del fusor (1x)

Can be obtained on Prusa E-shop

Paso 7 Attaching the hotend fan

⬢Attach the hotend fan to the heatsink using two M3x18 screws.

⬢Make sure the cable is pointing to the left.

⬢Guide the hotend fan cable through the groove in the x-carriage and plug it to the corresponding connector on the lower left part of the Loveboard.

Paso 8 Connecting the cables

⬢Guide the heater thermistor cable through the channel in the x-carriage and plug it to the corresponding connector on the Loveboard.

⬢Guide the heater cable through the channel in the x-carriage and plug it to the corresponding connector on the Loveboard.

Make sure none of the cables is protruding out of the cable groove in the X-carriage. Otherwise, the print fan won’t close. You can use the Allen key to gently push the cables in.

⬢Close the print fan and plug it to the corresponding connector on the Loveboard.

Paso 9 Finishing the fan installation

⬢Cover the extruder with the Loveboard cover on top. Make sure none of the cables gets pinched.

⬢La sustitución del ventilador ha terminado. Comprueba que el extrusor está montado como se ve en la imagen.

⬢Para probar la funcionalidad del ventilador, visita el menú Control -> Calibración y Tests > Test Ventiladores..

Como reemplazar un ventilador del fusor (MK4 / MK3.9)

Como reemplazar un ventilador del fusor (MK4 / MK3.9)

Paso 1 Introducción

Paso 2 Herramientas necesarias para este capitulo

Paso 3 Preparation

Paso 4 Disconnecting the cables

Paso 5 Removing the cables

Paso 6 Preparación de las piezas del ventilador del hotend

Paso 7 Attaching the hotend fan

Paso 8 Connecting the cables

Paso 9 Finishing the fan installation

Comentarios

¿Todavía tienes preguntas?