MK3.9

<p><strong>MK4 to MK4S upgrade <br /></strong></p>
<p>The current lead time is <strong>2-3 weeks </strong>for both xLCD versions.</p>
<table class="table" style="border-collapse: collapse; height: 330.828px; border-style: ridge; width: 100%;" border="1">
<tbody>
<tr style="height: 28.375px;">
<td style="width: 29.0798%; height: 28.375px; border-style: dotted; border-width: 1px; text-align: left;">Order week</td>
<td style="width: 29.2017%; height: 28.375px; border-style: dotted; border-width: 1px; text-align: left;">Order date</td>
<td style="width: 41.7185%; height: 28.375px; border-style: dotted; border-width: 1px; text-align: left;">Shipping estimate</td>
</tr>
<tr style="height: 33.25px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 33.25px;">Week 33</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 33.25px;">starts August 12, 2024</td>
<td style="width: 41.7185%; height: 33.25px; border-style: dotted; border-width: 1px; text-align: left;" rowspan="2">Already shipped</td>
</tr>
<tr style="height: 24.7344px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 24.7344px;">Week 34</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 24.7344px;">starts August 19, 2024</td>
</tr>
<tr style="height: 24.7344px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 24.7344px;">Week 35</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 24.7344px;">starts August 26, 2024</td>
<td style="width: 41.7185%; height: 101.203px; border-style: dotted; border-width: 1px; text-align: left;" rowspan="6">Currently shipping</td>
</tr>
<tr style="height: 24.7344px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 24.7344px;">Week 36</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 24.7344px;">starts September 2, 2024</td>
</tr>
<tr style="height: 27px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 27px;">Week 37</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 27px;">starts September 9, 2024</td>
</tr>
<tr style="height: 30px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 30px;">Week 38</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 30px;">starts September 16, 2024</td>
</tr>
<tr style="height: 27px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 27px;">Week 39</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 27px;">starts September 23, 2024</td>
</tr>
<tr style="height: 27px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 27px;">Week 40</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 27px;">starts September 30, 2024</td>
</tr>
<tr style="height: 21px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 21px;">Week 41</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 21px;">starts October 7, 2024</td>
<td style="width: 41.7185%; border-style: dotted; border-width: 1px; text-align: left; height: 84px;" rowspan="3">From week 47 (starts November 18, 2024)</td>
</tr>
<tr style="height: 21px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 21px;">Week 42</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 21px;">starts October 14, 2024</td>
</tr>
<tr style="height: 21px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 21px;">Week 43</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 21px;">starts October 21, 2024</td>
</tr>
<tr style="height: 21px;">
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left; height: 21px;">Week 44</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left; height: 21px;">starts October 28, 2024</td>
<td style="width: 41.7185%; border-style: dotted; border-width: 1px; text-align: left;" rowspan="3">From week 48 (starts November 25, 2024)</td>
</tr>
<tr>
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left;">Week 45</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left;">starts November 4, 2024</td>
</tr>
<tr>
<td style="width: 29.0798%; border-style: dotted; border-width: 1px; text-align: left;">Week 46</td>
<td style="width: 29.2017%; border-style: dotted; border-width: 1px; text-align: left;">starts November 11, 2024</td>
</tr>
</tbody>
</table>
<p></p>
<p> </p>
<h3><span style="font-size: 20px;">Current lead time estimates for new orders</span></h3>
<p><span style="color: #e67e23;"><strong>Updated: November 11th, 2024 </strong></span></p>
<p><em>The dates are only an estimation at the date of update, specified above, and rely on the actual</em> production. <em>We're doing our best but please be aware that it can shift for the lead time products. We will update here and on the product pages accordingly.</em></p>
<p>The lead time estimate applies to standalone products, other products in the order may increase the lead time.</p>
<p>If you've ordered a product in a bundle, the lead time of the order is set based on the product in the bundle with the longest lead time.</p>
<p> </p>
<p></p>
<table class="table" style="border-collapse: collapse; height: 765.922px; border-style: ridge; width: 100%;" border="1">
<tbody>
<tr style="height: 27.922px;">
<td style="height: 27.922px; width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center;">
<h4>Product</h4>
</td>
<td style="height: 27.922px; width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center;">
<h4>Lead time</h4>
</td>
</tr>
<tr style="height: 72px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>Original Prusa XL Enclosure<br /></strong><em>(standalone)</em><strong><br /></strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>In stock</strong></p>
</td>
</tr>
<tr style="height: 72px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>Advanced Filtration System <br /></strong>(for Original Prusa Enclosure)</p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>In stock</strong></p>
</td>
</tr>
<tr style="height: 72px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>MK4 to MK4S upgrade<br /></strong>/MK4S upgrade for versions with old xLCD</p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>2-3 weeks</strong></p>
</td>
</tr>
<tr style="height: 72px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>MK3.9 to MK3.9S upgrade</strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>In stock</strong></p>
</td>
</tr>
<tr style="height: 51px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>MK3S/+ to MK4S upgrade</strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>2-3 weeks</strong></p>
</td>
</tr>
<tr>
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center;">
<p><strong>MK3S/+ to MK3.9S upgrade</strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center;">
<p><strong>In stock</strong></p>
</td>
</tr>
<tr style="height: 51px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>MK3S/+ to MK3.5S upgrade</strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>In stock</strong></p>
</td>
</tr>
<tr style="height: 72px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>Original Prusa MMU3 upgrade kit (for MK4S/MK3.9S)</strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>1-2 weeks</strong></p>
</td>
</tr>
<tr style="height: 51px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>MMU3 assembled unit (for MK4S/MK3.9S) </strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>1-2 weeks</strong></p>
</td>
</tr>
<tr style="height: 51px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>MMU3 assembled unit (for MK4/MK3.9)</strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>In stock</strong></p>
</td>
</tr>
<tr style="height: 51px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>MMU3 assembled unit (for MK3.5S/MK3.5) </strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>In stock</strong></p>
</td>
</tr>
<tr style="height: 51px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>MMU3 assembled unit (for MK3S+) </strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 51px;">
<p><strong>In stock</strong></p>
</td>
</tr>
<tr style="height: 72px;">
<td style="width: 48.3436%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>Original Prusa MMU2S to MMU3 upgrade<br />for MK4S/MK3.9S</strong></p>
</td>
<td style="width: 51.6564%; border-style: dotted; border-width: 1px; text-align: center; height: 72px;">
<p><strong>1-2 weeks</strong></p>
</td>
</tr>
</tbody>
</table>
<p>You can find your order shipping date in the order detail section in our shop.</p>
<div class="note-callout">All products purchased in our <a href="https://shop.prusa3d.com/">online store</a> are currently being shipped from the<strong> Czech Republic, </strong>a member state of the <strong>European Union, customs charges may apply for shipments to countries outside of the EU!</strong> Please see our advisory article <a href="http://help.prusa3d.com/article/vat-value-added-tax-customs-fees_1505#orders-outside-eu">here</a>.</div>

Shipping information

Infill patterns

<div class="warning-callout">This is an&nbsp;<strong>advanced calibration</strong>, recommended only to&nbsp;<strong>experienced users</strong>.</div>
<p>The Extrusion Multiplier allows the fine-tuning of the extrusion flow rate - simply described as&nbsp;<strong>how much filament comes out of the nozzle</strong>. In other words, the&nbsp;<strong>Extrusion Multiplier</strong>&nbsp;setting in PrusaSlicer and the&nbsp;<strong>Flow rate</strong>&nbsp;setting in printer firmware are two ways to adjust the same thing, however, adjusting one of those two settings will not influence the value of the other.</p>
<p><strong>This procedure is not necessary with a new printer coming from the factory</strong>, but rather applies for specific applications and filaments. The ideal value is different for every type of material and every color. It can even differ from spool to spool. Bear this in mind if you change type and brand of filament often or use cheap no-name brands.</p>
<div class="note-callout">Total flow rate = <strong>Flow multiplier</strong> in firmware (M221) x <strong>Extrusion multiplier</strong> in PrusaSlicer. For those interested in diving deeper, PrusaSlicer uses the same <a href="https://manual.slic3r.org/advanced/flow-math">Flow math as Slic3r</a>.</div>
<h3><strong>How to spot an issue</strong></h3>
<p>This calibration is used to fix two common problems:</p>
<ul>
<li><strong>Overextrusion</strong> - Too much material is extruded (flow is too high). It causes scarring of bottom layers and unnecessary material buildup on top layers.</li>
<li><strong>Minor under extrusion</strong>&nbsp;- Not enough material is extruded (flow is too low). It causes small gaps that appear between layer lines or perimeters.</li>
</ul>
<p><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/under-ok-over.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/under-ok-over-600x282.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/under-ok-over-800x376.jpg 800w, https://cdn.help.prusa3d.com/wp-content/uploads/under-ok-over-300x141.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/under-ok-over-768x361.jpg 768w, https://cdn.help.prusa3d.com/wp-content/uploads/under-ok-over-1536x721.jpg 1536w" alt="" width="852" height="400"></p>
<p><strong>Overextrusion</strong> is a common problem with many filament brands. It's especially problematic when you're trying to glue two parts of the model. <strong>If the top layer is over extruded, you'll end up with an uneven surface that will prevent a seamless connection between the two pieces.</strong></p>
<h3><strong>How to do the calibration</strong></h3>
<p>In PrusaSlicer, navigate to <span class="key">Filament Settings</span> and look for Extrusion Multiplier. The default setting (for PLA) is 1, this value represents a percentage, 1 = 100%, 0.95 = 95% etc. Usually, the adjusted values can be between 0.9 and 1.1. To adjust it, simply rewrite the value.</p>
<p><img decoding="async" style="max-height: 200px; display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusuki/prusuki-images/image-2019-1-15-12-55-6.png" data-hd-height="200px"></p>
<p>In the printer menu, during a print, go to the Tune menu and then choose Flow. Again, the usual values can range between 90 and 110, although that does not mean you can't go above or below that.</p>
<h4>Which method should I use?</h4>
<p>There are two methods you can use to calibrate the Extrusion Multiplier, and we'll cover both of them in this article:</p>
<ul>
<li><strong>Precise Method</strong>&nbsp; -&nbsp; using precision tools such as calipers or micrometers.</li>
<li><strong>Visual Method&nbsp;</strong>&nbsp;- an easy method based on observing the visual properties of your models.</li>
</ul>
<p>The choice of the method depends entirely on your preferences; in the end, both yield similar results. Even the visual method will enable you to have perfectly fitting parts with smooth &amp; flat top layers.</p>
<h4>Precise Method</h4>
<div class="note-callout">Please note that the following guide is based on <strong>default</strong> PrusaSlicer 0.4 nozzle profiles, with a layer height of 0.1mm - 0.2mm. This means that:<br />
- Nozzle size = 0.4<br />
- Extrusion width =&nbsp;0.45<br />
- Basic materials (PLA, ABS, PETG) Extrusion Multiplier = 1<br />
<strong>If you wish to calibrate the printer with a bigger/smaller nozzle or layer heights above 0.2, then you will need to adjust these values as well.</strong></div>
<ol>
<li>Download the <a href="https://cdn.help.prusa3d.com/wp-content/uploads/2021/04/cube-40-40-40.zip">Precision Method Cube STL</a>.</li>
<li>Slice it using the Vase Mode and your most-often used layer height and print it. You can find Vase mode (Print Settings →&nbsp; Layers and perimeters →&nbsp; Spiral vase).</li>
<li>Make three or more measurements in the middle of each wall and calculate the overall average thickness.</li>
<li>Calculate the extrusion multiplier using the following formula: <strong>Extrusion multiplier = (Extrusion width (0.45) / Average measured wall thickness)</strong>.</li>
<li>Adjust the Extrusion Multiplier in Filament Settings → Filament</li>
<li>Re-print the cube with new settings and go back to step 3 if necessary.</li>
</ol>
<p><img decoding="async" style="max-height: 220px; display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusuki/prusuki-images/micrometer-small-jpg.JPG" height="400" data-hd-height="220px"></p>
<div class="warning-callout">Please note that cheap digital calipers may not be accurate enough to make reliable measurements of a single perimeter wall.</div>
<h4>Visual Method</h4>
<p>This method does not require any tools, only your sight. The point is to make sure your top layers are <strong>smooth</strong>, <strong>shiny,</strong> and without <strong>scarring or filament buildup</strong> near the perimeters.</p>
<p><img decoding="async" loading="lazy" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/destiky6.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/destiky6-600x374.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/destiky6-800x499.jpg 800w, https://cdn.help.prusa3d.com/wp-content/uploads/destiky6-300x187.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/destiky6-768x479.jpg 768w, https://cdn.help.prusa3d.com/wp-content/uploads/destiky6-1536x958.jpg 1536w" alt="" width="641" height="400"></p>
<ol>
<li>Download the <a href="https://cdn.help.prusa3d.com/wp-content/uploads/2021/04/visual-method-cube.zip">Visual Method Cube.stl</a></li>
<li>Slice it using the default Prusa PLA presets at 0.20mm layer height and print it.</li>
<li>Inspect the top layer of your cube visually and with the tip of the finger.</li>
<li>If the top is under extruded or not smooth, then re-adjust the Extrusion Multiplier accordingly by 1-2%.</li>
<li>Repeat the steps above as long as needed.</li>
</ol>
<p>If there is&nbsp;<strong>too much material</strong>&nbsp;near the perimeters,&nbsp;<strong>decrease</strong>&nbsp;the Extrusion Multiplier value.</p>
<p><img decoding="async" style="max-height: 390px; margin-left: auto; margin-right: auto; display: block;" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusuki/prusuki-images/buildu.jpg" data-hd-height="390px" data-hd-align="left"></p>
<p>If there are&nbsp;<strong>visible gaps</strong>&nbsp;between layer lines,&nbsp;<strong>increase</strong> the Extrusion Multiplier value. (Microscopic gaps near the perimeters are OK.)</p>
<p><img decoding="async" style="max-height: 430px; margin-left: auto; margin-right: auto; display: block;" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusuki/prusuki-images/gaps.jpg" data-hd-height="430px" data-hd-align="left"></p>


Extrusion multiplier calibration

<p>Stringing or oozing, also known as "hairy prints", is the name given for when small strings of filament are left on a printed model. This usually happens when the filament keeps flowing from the nozzle while the extruder is moving to another object. You can see this as a marginal line of filament left between the objects.</p>
<p>This issue is caused by <strong>very high printing temperatures and/or using incorrect retraction settings</strong>. This can be solved by changing a couple of settings in PrusaSlicer and checking your hardware.</p>
<table style="border-collapse: collapse; width: 100%;" border="0">
<tbody>
<tr>
<td style="width: 48.8442%;"><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/90014ff5fc80d10b.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/90014ff5fc80d10b-600x383.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/90014ff5fc80d10b-800x511.jpg 800w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/90014ff5fc80d10b-300x192.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/90014ff5fc80d10b-768x490.jpg 768w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/90014ff5fc80d10b-1536x981.jpg 1536w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/90014ff5fc80d10b-2048x1308.jpg 2048w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/90014ff5fc80d10b.jpg 1600w" alt="" width="400" height="255"></td>
<td style="width: 48.8442%;"><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/b1b72c32290b8c00.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/b1b72c32290b8c00-600x400.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/b1b72c32290b8c00-800x534.jpg 800w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/b1b72c32290b8c00-300x200.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/b1b72c32290b8c00-768x512.jpg 768w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/b1b72c32290b8c00.jpg 1600w" alt="" width="400" height="267"></td>
</tr>
</tbody>
</table>
<h3>Stringing from material left on the nozzle</h3>
<p>If you print for a long time from a single type of filament, such as PET-G, the filament can create a thin layer in the nozzle. This can cause stringing as the strands of the filament stick to the surface of the print. Therefore, thoroughly clean the nozzle before printing and make sure that any dirt or remnants of previous filaments are removed from the nozzle.</p>
<div class="warning-callout">We highly recommend using our official (factory default) preset settings in PrusaSlicer. However, if you are printing with your own settings, make sure that you have the retraction settings configured correctly.</div>
<h3>PrusaSlicer settings</h3>
<p><img decoding="async" loading="lazy" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/432d664dd4b64d78_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/432d664dd4b64d78_painted-600x359.jpeg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/432d664dd4b64d78_painted-800x479.jpeg 800w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/432d664dd4b64d78_painted-300x179.jpeg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/432d664dd4b64d78_painted-768x459.jpeg 768w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/432d664dd4b64d78_painted-1536x919.jpeg 1536w, https://cdn.help.prusa3d.com/wp-content/uploads/2022/02/432d664dd4b64d78_painted.jpeg 1600w" alt="" width="700" height="419"></p>
<p>You should start by checking a parameter known as Retraction. What does retraction do? When the extruder has finished printing one section/object of your g-code, the filament is pulled back into the nozzle. Once the extruder moves to the next location the printing process continues – the filament is pushed back out and it starts extruding from the nozzle again. Retraction settings can be found in PrusaSlicer in <em>Printer Settings -&gt; Extruder 1</em>.</p>
<p>Flexible filaments usually need longer retractions, because the material stretches while being pulled back to the nozzle. Flexible materials are a special case and can need a lot of tweaking and tuning.</p>
<p><strong>The retraction settings are:</strong></p>
<ul>
<li><strong>Retraction length:</strong> Amount that the filament is pulled back when a retraction is triggered. <strong>On the MK2.5/S and MK3/S/+, the retraction length should be a maximum of 2 mm.</strong></li>
</ul>
<div class="tip-callout">Due to the Bowden extruder, the retraction length of the Original Prusa MINI/MINI+ presets are much longer (default 3.2 mm).</div>
<ul>
<li><strong>Lift z:</strong> lifts the extruder during movement. Having this setting lower will improve stringing. Note that disabling this feature may cause the nozzle to hit the printed part.<strong><br /></strong></li>
<li><strong>Retraction Speed:</strong> Extruder motor speed on retraction. A higher value improves stringing, but if it is too high it may skip steps in the motor.</li>
<li><strong>Minimum travel after retraction:</strong> Amount of move that will trigger a retraction (mm). The preset number in PrusaSlicer is 1 mm, which is a low amount. Having this number higher will get lower printing times, but increase oozing and stringing.</li>
<li><strong>Retract on layer change:</strong> Activates retraction when the layer changes to the next one. It is recommended to leave this option on.</li>
<li><strong>Wipe while retracting:</strong> Moves the nozzle (wipe) while the retraction is happening. It is recommended to leave this option on.</li>
<li><strong>Retract amount before wiping:</strong> This option does a quick retract before doing the wiping movement. More suitable for the Original Prusa MINI/MINI+.</li>
</ul>
<p><strong>Other settings that affect retraction:</strong></p>
<ul>
<li><strong>Only retract when crossing perimeters:</strong> <em>(Print settings -&gt; Infill -&gt; Advanced):</em> Disables retraction when the travel path does not exceed the upper layer's perimeter. Any oozing that happens will be within the walls and should be invisible.</li>
<li><strong>Avoid crossing perimeters:</strong> <em>(Print settings -&gt; Layers and perimeters -&gt; Quality):</em> Optimize travel moves in order to minimize the crossing of perimeters. This will lower the stringing amount, especially in the MINI/MINI+.</li>
<li><strong><a href="http://help.prusa3d.com/article/sequential-printing_124589">Sequential printing</a>:</strong> <em>(Print settings -&gt; Output options -&gt; Sequential printing):</em> Printing each object individually has a smaller chance of causing stringing between the parts. When using this feature, PrusaSlicer will warn you of any possibility of the extruder colliding with an already printed part, but follow the print closely.</li>
<li><strong>Nozzle temperature:</strong> <em>(Filament settings -&gt; Filament -&gt; Nozzle):</em> Lowering the temperature decreases the occurrence of strings. Try decreasing the nozzle temperature by 5 – 10°C and check whether there’s less stringing.</li>
</ul>
<h3>Filament</h3>
<p>Try using a different spool than the one that is causing the stringing. The filament might have gathered moisture, which will cause a lot of stringing.</p>
<h3>Hotend</h3>
<p>Stringing in the nozzle might be caused by a heat dissipation issue in the nozzle. Try <a href="http://help.prusa3d.com/guide/how-to-replace-a-heatbreak-heatsink-heaterblock-mk3s-mk3s-mk2-5s-mmu2s_16104">re-applying thermal paste</a> on the threads between the heatbreak and the heatsink.</p>
<p>If you have recently changed any component in the hotend, it is also possible that some individual parts are not in place. Go over the assembly of the hotend and check for any parts that may be different from the <a href="http://help.prusa3d.com/guide/how-to-replace-a-heatbreak-heatsink-heaterblock-mk3s-mk3s-mk2-5s-mmu2s_16104">instructions</a>.</p>
<h3>Enough settings, pass me my <strong>heat-gun!</strong></h3>
<p>If you don’t feel like tweaking any of the settings, well, then there is an alternative. You can get rid of the strings with a heat gun (or often with a lighter – but be very careful). Set your heat-gun to around 200 °C and aim at the strings for one or two seconds. This will melt the strings, and the printed object should remain undamaged. Do not leave the heat source on the printed model for longer than one or two seconds, as this may deform the part.</p>


Stringing and oozing

<div><strong><img decoding="async" loading="lazy" style="float: right;" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-400x400.jpg 400w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-600x600.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-300x300.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-768x768.jpg 768w" alt="" width="225" height="225"></strong></div>
<h3>Basic info</h3>
<div><strong>PETG</strong> is one of the most easily printable materials, it is <strong>inexpensive and suitable for beginners</strong>. Relatively high tenacity and temperature resistance make it <strong>suitable for printing technical parts</strong> (for example parts of our printers).</div>
<div>&nbsp;</div>
<div><strong>Recommended nozzle temperature:</strong> 230 °C for the first layer, 240 °C for the other layers</div>
<div>&nbsp;</div>
<div><strong>Recommended bed temperature:</strong> 85 °C for the first layer, 90 °C for the other layers</div>
<div>&nbsp;</div>
<div><strong>Heatbed:</strong> Using powder-coated TXT or satin sheet is highly recommended. Printing on smooth PEI surface might damage the sheet.</div>
<h3>Description</h3>
<div>
<p><a href="https://www.prusa3d.com/category/prusament-petg/"><strong data-stringify-type="bold">PETG</strong></a> (Polyethylene Terephthalate modified with Glycol) is a commonly used technical material, popular among 3D printer users for its <strong>low price and good printability</strong>. It’s tenacious, with good temperature resistance; PETG is most commonly used for printing various mechanical parts, holders, clamps, and waterproof parts (thanks to great layer adhesion).</p>
<p>PETG has a glossy surface, adheres greatly to a print sheet, and <strong>does not shrink or warp</strong> (it has very little thermal expansion), therefore it’s suitable for printing large models. Plus, its high tenacity and flexibility often <strong>prevent it from breaking.</strong> Due to good temperature resistance, PETG parts are suitable both for interior and most exterior use (with temperatures below 80 °C). <strong>Parts of our printers are made of PETG!</strong></p>
<p>The letter G in PETG means that it’s modified with glycol during the manufacturing process. Glycol makes PET less brittle, easier to print, and more transparent for translucent prints. Of course, you can print also with PET filaments without glycol. However, printing with only PET is challenging and does not offer any advantage whatsoever.</p>
<div class="warning-callout">Even though PETG in itself may be considered <a href="http://help.prusa3d.com/article/food-safe-fdm-printing_112313">food-safe</a>, it consists of layers, as every 3D print, in which bacteria can grow over time. You can prevent this by applying a <strong>food-safe(epoxy) coating.</strong> Also, a stainless-steel nozzle should be used for if food is the intended application.</div>
<p>Although <strong>PETG</strong> is frequently used in <strong>food industry</strong> and is considered <strong>food-safe</strong>, we do not recommend it (or any other filament) for printing dishes or other stuff that comes into direct contact with food. The main reason is tiny print layer surface grooves that can support numerous bacterial colonies. But if you still want 3D printed dishes, we suggest <strong>applying a special layer</strong> that seals the surface (food-safe coating) and printing with a clean steel nozzle.</p>
<p>Some of the manufacturers <strong>enrich PETG with various additives</strong> and sell these materials under different names. For example, Spoolworks EDGE by E3D is modified PET/Copolyester Blend with additives. The goal is to acquire better visual qualities, surface and layer adhesion, etc.</p>
<p>To compare supported material properties, see our <a href="https://help.prusa3d.com/en/materials">material table.</a></p>
</div>
<table class="striped">
<tbody>
<tr>
<th>
<p>Pros</p>
</th>
<th>
<p>Cons</p>
</th>
</tr>
<tr>
<td>
<p>✔ Easy to print</p>
</td>
<td>
<p>✖ Possibility of stringing</p>
</td>
</tr>
<tr>
<td>
<p>✔ Good layer adhesion</p>
</td>
<td>
<p>✖ Poor bridging and overhangs</p>
</td>
</tr>
<tr>
<td>
<p>✔ Tough and durable</p>
</td>
<td>
<p>✖ Not great for printing detailed parts</p>
</td>
</tr>
<tr>
<td>
<p>✔ Low warping</p>
</td>
<td>
<p>✖ Bonds strongly to the print surface</p>
</td>
</tr>
<tr>
<td>✔ High temperature-resistance</td>
<td>
<p>✖ Soluble in dangerous chemicals</p>
</td>
</tr>
<tr>
<td>✔ Water and humidity resistant</td>
<td>
<p>✖ Supports are hard to remove</p>
</td>
</tr>
</tbody>
</table>
<h3>Best use</h3>
<p>PETG is used universally but is especially suitable for mechanical parts for both indoor and outdoor use. We use PETG to print parts for our printers! Plastic bottles are also made from this kind of material.</p>
<h3>Tips for successful printing</h3>
<p><strong>Temperature settings and cooling</strong></p>
<p>Unlike PLA, <strong>PETG requires a heated bed (85 °C).</strong> Its bridging- and overhang-behavior is usually worse, plus it is prone to stringing. Stringing can be moderated with higher retractions and lower nozzle temperature, but we suggest <strong>using the PrusaSlicer profiles that should work fine.</strong> It’s important to <strong>cool the PETG print</strong> - this helps to keep the model detailed and prevents stringing and oozing. But if you want the model to be as tough as possible, try to turn off the print fan. Higher filament temperature improves merging between layers which leads to better mechanical resistance. Otherwise, we recommend printing the first few layers with the print fan off to prevent deformation, then with the fan running at half its power.</p>
<div class="warning-callout"><strong>Do not print on the smooth PEI sheet</strong> as the adhesion may be too strong!</div>
<p><strong>Print surface preparation</strong></p>
<p>Make sure the print surface is clean, as described in <a href="http://help.prusa3d.com/article/first-layer-issues_1804">our dedicated article</a>. It is advisable to use one of the <strong>powder-coated print sheets. Do not print on the smooth PEI sheet</strong> as the adhesion may be too strong! If you decide to use the smooth PEI sheet anyway, apply a glue stick on it before printing.</p>
<p><strong>Adding more perimeters for more solid parts</strong></p>
<p>If you want to print truly solid parts, <strong>try to increase the number of perimeters</strong> instead of adding more infill.</p>
<h3>Postprocessing</h3>
<p>PETG can be easily sanded both dry and wet.</p>
<p><strong>Dissolving PETG</strong></p>
<p><strong>Dissolving and smoothing PETG</strong> is possible only in a laboratory by skilled lab workers using <strong>dangerous chemicals</strong> (Dichloromethane).</p>
<h3>Sample prints</h3>
<table style="border-collapse: collapse; width: 100%; height: 954px;" border="0">
<tbody>
<tr style="height: 300px;">
<td style="width: 48.805%; height: 300px;"><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-1-1.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-1-1-400x400.jpg 400w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-1-1-600x600.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-1-1-300x300.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-1-1-768x768.jpg 768w" alt="" width="800" height="800"></td>
<td style="width: 48.805%; height: 300px;"><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-jet-black-1kg.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-jet-black-1kg-400x400.jpg 400w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-jet-black-1kg-600x600.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-jet-black-1kg-300x300.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-jet-black-1kg-768x768.jpg 768w" alt="" width="800" height="800"></td>
</tr>
<tr style="height: 18px;">
<td style="width: 48.805%; height: 18px; text-align: center;"><em>MMU (Multi-Material Unit)</em></td>
<td style="width: 48.805%; height: 18px; text-align: center;"><em>Electronics cover and other printer parts</em></td>
</tr>
<tr style="height: 300px;">
<td style="width: 48.805%; height: 300px;"><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-2.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-2-400x400.jpg 400w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-2-600x600.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-2-300x300.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-2-768x768.jpg 768w" alt="" width="800" height="800"></td>
<td style="width: 48.805%; height: 300px;"><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-3.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-3-400x400.jpg 400w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-3-600x600.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-3-300x300.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-prusa-orange-1kg-3-768x768.jpg 768w" alt="" width="800" height="800"></td>
</tr>
<tr style="height: 18px;">
<td style="width: 48.805%; height: 18px; text-align: center;"><em>Ukulele</em></td>
<td style="width: 48.805%; height: 18px; text-align: center;"><em>Various mechanical parts</em></td>
</tr>
<tr style="height: 300px;">
<td style="width: 48.805%; height: 300px; text-align: center;"><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-1.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-1-400x400.jpg 400w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-1-600x600.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-1-300x300.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-1-768x768.jpg 768w" alt="" width="800" height="800"></td>
<td style="width: 48.805%; height: 300px; text-align: center;"><img decoding="async" loading="lazy" src="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg.jpg" sizes="100vw" srcset="https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-400x400.jpg 400w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-600x600.jpg 600w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-300x300.jpg 300w, https://cdn.help.prusa3d.com/wp-content/uploads/prusament-petg-urban-grey-1kg-768x768.jpg 768w" alt="" width="800" height="800"></td>
</tr>
<tr style="height: 18px;">
<td style="width: 48.805%; height: 18px; text-align: center;"><em>Electronic parts</em></td>
<td style="width: 48.805%; height: 18px; text-align: center;"><em>Boxes and organizers</em></td>
</tr>
</tbody>
</table>


PETG

Original Prusa i3 MK3/MK3S/MK3S+ to MK3.9 upgrade

Assembly manuals

Basic calibration

Advanced calibration

All information you need to know to learn how to calibrate your 3D printer to achieve perfect prints.

Calibration

Printer description

Printer features

FAQs and other useful information you might be interested in before or after making your purchase at shop.prusa3d.com

General Information

Basic overview of your 3D printer and it's features, plus general Prusa Research info.

About your printer

3D models

Material guide

Printer maintenance

Prusa Connect & PrusaLink

In this section, you can find material guides, printer troubleshooting and general info about using your printer.

Using the printer

Print Quality Troubleshooting

QR Error codes

Printer troubleshooting

Description of how to recognize and solve common problems, especially hardware and electronics related.

Troubleshooting

Nozzles

Octoprint

Learn about different nozzles, Raspberry Pi connection, Octoprint and more.

3rd party accessories & Other projects

About PrusaSlicer

Configuration and profiles

User interface

Input/output

Top toolbar

Print settings

Filament settings

Advanced features

The official documentation for the PrusaSlicer slicing software. From basic configuration to advanced settings like modifier meshes.

PrusaSlicer

1. Introduction

1a. Parts check

1b. Printer disassembly

1c. Parts preparation

2. Frame assembly

3. X-axis & X-carriage assembly

4. Z-axis assembly

5. Nextruder assembly

6. xLCD assembly

7. Y-carriage & Heatbed assembly

8. Preflight check

Manual changelog MK3.9 upgrade

Prusa Connect &amp; PrusaLink

<h3>What happened? </h3>
<p>During the configuration of <strong>Prusa Connect</strong> on the <strong>Original Prusa MINI/+</strong>, <strong>MK4/S</strong>, <strong>MK3.9/S, MK3.5/S</strong> or <strong>XL</strong> an error on this configuration can occur and the printer shows the message "<strong>Registration to Prusa Connect failed due to: ~</strong>". In place of <strong>~</strong>, a text with more details is shown, from the list below. Depending on the specific shown text, there are different causes and fixes. </p>
<p>Error name: Connect Registration Failed</p>
<p>Error code: #12401 (MINI), #13401 (MK4), #26401 (MK4S), #21401 (MK3.9), #23401 (MK3.5), #17401 (XL)</p>
<h4>DNS error</h4>
<p>The printer wasn't able to resolve the <strong>hostname</strong> of the Prusa Connect server into an IP address. The hostname is a unique label assigned to a device connected to a network. </p>
<ul>
<li>The printer is not connected to the network at all.</li>
<li>In case of a <strong>static</strong> configuration (non-DHCP), the <strong>DNS server</strong> is not configured or configured incorrectly.</li>
<li>The local DNS server is currently not working.</li>
<li>The Connect hostname is reconfigured to some that doesn't exist. For example, this can occur if loading a .ini file with an invalid configuration.</li>
</ul>
<h4>Refused</h4>
<p>It's not possible to reach the server on the network level, hence it is not possible to establish a TCP connection. The system is either not answering at all or actively refuses the connection. </p>
<ul>
<li>The internet connection is not working, or a firewall blocks the communication.</li>
<li>In the case of a <strong>static</strong> configuration (non-DHCP), the <strong>gateway </strong>(typically, this is the IP address of the router) is not configured or configured incorrectly. </li>
<li>The Connect server is under maintenance. </li>
<li>Too many TCP connections are open with the printer, for example in PrusaLink. </li>
</ul>
<h4>TLS error</h4>
<p>This message points to an error doing a <strong>SSL/TLS handshake</strong>. This handshake is the process to create a safe and encrypted connection. </p>
<ul>
<li>Time is not synchronized on the printer (MINI/+). The time synchronization occurs for each internet connection, through the <a href="http://help.prusa3d.com/article/ntp-server-mini_151132">NTP server</a>. It is possible this might take more time than initially expected, or rarely, that there might be issues with the server. </li>
<li>A restrictive firewall (for example but not limited to a corporate proxy firewall) may restrict an automatic access to the NTP server. In that case, it will be necessary to manually allow the printer to access the NTP server.</li>
<li>Something in the path is trying to tamper with the communication, for example but not limited to an attack. </li>
</ul>
<h4>Unauthorized</h4>
<p>The server claims that the printer is not authorized. The printer is not recognized as an Original Prusa. </p>
<h4>Server error</h4>
<p>The server is returning a <strong>500 Internal Server Error</strong> or similar. The issue is on the Connect side, and is expected to be fixed on its own. </p>
<h4>Internal error</h4>
<p>This error is caused by an issue related to the printer firmware. </p>
<h4>Network error</h4>
<p>Similar to the Refused error, but the connection dropped after it was initialized. </p>
<ul>
<li>Glitchy internet connection.</li>
<li>The <strong>latency</strong> to the Connect servers is too high. A geographic location is very far from our Connect servers can contribute to this cause.</li>
<li>The Connect server is temporarily down.</li>
</ul>
<h4>Protocol error</h4>
<p>The response from the server is not recognized.</p>
<ul>
<li>Bug on the server side. This cause is on our side and expected to be fixed on its own. </li>
<li>Too old firmware on the printer and it's no longer supported.</li>
<li>A misconfiguration from the <strong>.ini file</strong> loaded on the printer, connecting to something different than our Connect server.</li>
</ul>
<h3>How to fix it? </h3>
<h4>DNS error, Refused</h4>
<p>Ensure that the printer is connected to the internet. In case of a static (non-DHCP) connection, ensure the correct settings are there, or test a DHCP connection. Also, check the .ini configuration file, and in case, rewrite the file. </p>
<p>If the previous steps didn't fix the issue, attempt a <a href="http://help.prusa3d.com/article/factory-reset-mini_177516">factory reset</a>. </p>
<h4>TLS error</h4>
<p>Reattempt the Connect registration, after the printer is connected to the internet for a few more minutes. </p>
<p>If the previous step didn't fix the issue, double-check your network <strong>firewall</strong>. Some firewalls will need for the NTP server to be allowed manually. The specific steps will depend on your specific firewall, we recommend checking your firewall documentation. </p>
<h4>Unauthorized</h4>
<p>If your printer is not an Original Prusa printer, it cannot use our Prusa Connect service.</p>
<p>In case your printer is an Original Prusa, <a href="http://help.prusa3d.com/article/firmware-updating-mini-mini_124784"> re-flash or update its firmware</a>. </p>
<h4>Server error</h4>
<p>A server error indicates an issue from our side. The issue will be fixed on its own, try registering again to Prusa Connect later. </p>
<h4>Internal error</h4>
<p><a href="http://help.prusa3d.com/article/firmware-updating-mini-mini_124784">Re-flash or update the printer firmware</a>. If this does not solve the issue, take note if the printer might have other issues, even if not directly related. </p>
<h4>Network error</h4>
<p>Ensure that your internet connection is stable and not glitchy. To confirm whether an inconsistent internet connection caused the issue, test another connection, if available, such as a hotspot from your mobile phone. </p>
<h4>Protocol error</h4>
<p>Ensure that the printer is running our latest firmware version. If it is running an old version, update the firmware. Also, check the .ini configuration file, and in case, rewrite the file.</p>


Connect Registration Failed

<h3>What happened?</h3>
<p>The Original Prusa MK4S/MK4/MK3.9/MK3.5 displays the message: "<strong>Failed to home the extruder in X-axis, make sure there is no obstacle on X-axis</strong>".</p>
<p>Error name: Homing error X</p>
<p>Error code: #26304 (MK4S) #13304 (MK4) #21304 (MK3.9) #23304 (MK3.5)</p>
<p>The error is most likely caused by a bad movement of the print head along the X-axis. </p>
<h3>How to fix it? </h3>
<h4>X-axis movement</h4>
<p>Make sure there are no obstructions in the path of the X-axis. For example, there might be a piece of filament stuck around the belt, or on a smooth rod, from a previous print.</p>
<h4>X-axis belt tension</h4>
<p>Check the X-axis belt tension and adjust it, following our <a href="http://help.prusa3d.com/article/adjusting-belt-tension-mk4-s-mk3-9-s-mk3-5-s-mk3-s_112380">dedicated article on belt adjustment</a>.</p>
<h4>X-axis motor pulley</h4>
<p>The X-axis motor pulley is attached to the X-axis motor shaft. The motor shaft has one flat side. The pulley has two set screws: ensure that one of the two set screws is aligned with the flat part of the motor shaft. Make sure the other set screw is also tightened, not excessively, and that there is a small space between the pulley and the motor. </p>
<h4>X-carriage assembly</h4>
<p>An over-tightened or loose X-carriage and X-carriage-clip assembly might cause the error. If none of the previous steps resolved the issue, refer to our <a href="http://help.prusa3d.com/guide/3-x-axis-x-carriage-assembly_429986">assembly manual</a> to see the assembly of the X-carriage and X-carriage-clip.</p>
<h4>xBuddy connection</h4>
<p>Check the motor connections on the board. For that, open the four screws that hold the xBuddy box cover. Make sure that the motor connector is not loose, and that the X-axis motor connector has not been accidentally switched with the Y-axis motor or any other motor.</p>
<table style="border-collapse: collapse; width: 100.026%;" border="0">
<tbody>
<tr>
<td style="width: 48.7906%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/10/9769d45d75346583db549d162dbb302b_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Homing error Y #13305 (MK4) #21305 (MK3.9)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.7906%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/10/a5df42079c5152c4bb1404adc18106ea.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Homing error Y #13305 (MK4) #21305 (MK3.9)" alt="" width="400" height="300" loading="lazy" /></td>
</tr>
</tbody>
</table>


Homing error X #26304 (MK4S) #13304 (MK4) #21304 (MK3.9) #23304 (MK3.5)

<p>The Original Prusa MK4/S, MK3.9, and XL are equipped with a <a href="http://help.prusa3d.com/article/loadcell-mk4-s-mk3-9-s-xl_401253">loadcell</a>. Thanks to this component, starting from firmware 6.0.0, the printer is able to detect whether the filament is stuck and not moving, for example when the nozzle is clogged. </p>
<p>In case this is detected, the print pauses and the printer shows the message: "<strong>Stuck filament detected. The filament seems to be stuck, please unload it from nextruder and load it again</strong>". </p>
<p>Once the <strong>unload </strong>button is pressed, the printer unloads the filament. After this, the printer prompts filament loading, and resumes the print. </p>
<div class="tip-callout">It is important to note that detecting stuck filament is possible only inside the Nextruder, as pressure builds up from the nozzle to the upper part of the Nextruder. However, if your filament is tangled on the spool, there will be no internal pressure, just outside tension, which the loadcell won't be able to recognize.</div>
<div>Stuck filament detection won't be possible on MK3.5 and MINI/MINI+ as they aren't equipped with the loadcell sensor. </div>
<p style="text-align: center;"><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2024/04/e884e31f8ae9e52017bacbeb8fcd544e.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Stuck filament detection #13101 (MK4) #21101 (MK3.9)" alt="" width="500" height="333" loading="lazy" /><em>Screenshot from the Original Prusa MK4</em></p>


Stuck filament detection #26101 (MK4S) #13101 (MK4) #21101 (MK3.9) #17108 (XL)

<h3>What happened?</h3>
<p>The Original Prusa MK4S/MK4/MK3.9/MK3.5 displays the message: <strong>"Failed to home the Y-axis, make sure there is no obstacle on Y-axis</strong>".</p>
<p>Error name: Homing error Y</p>
<p>Error code: #26305 (MK4S) #13305 (MK4) #21305 (MK3.9) #23305 (MK3.5)</p>
<p>The error is most likely caused by a bad movement of the Y-carriage along the Y-axis.</p>
<h3>How to fix it? </h3>
<h4>Y-axis movement</h4>
<p>Make sure there are no obstructions in the path of the Y-axis. For example, there might be a piece of filament stuck around the belt, or on a smooth rod, from a previous print.</p>
<h4>Y-axis belt tension</h4>
<p>Check the Y-axis belt tension and adjust it, following our <a href="http://help.prusa3d.com/article/adjusting-belt-tension-mk4-s-mk3-9-s-mk3-5-s-mk3-s_112380">dedicated article on belt adjustment</a>.</p>
<h4>Y-axis motor pulley</h4>
<p>The Y-axis motor pulley is attached to the Y-axis motor shaft. The motor shaft has one flat side. The pulley has two set screws, ensure that one of the two set screws is aligned with the flat part of the motor shaft. Make sure the other set screw is also tightened, not excessively, and that there is a small space between the pulley and the motor.</p>
<h4>Y-axis bearings position</h4>
<p>Incorrect positioning of the bearings might cause the error.</p>
<p>On the side of the Y-carriage with one bearing, ensure that the bearing is centered on the bearing clip. Approximately the same piece of bearing should be visible on each side.</p>
<p>On the side of the Y-carriage with two bearings, place the bearings as close to the center of the Y-carriage as possible. Beware, the bearings must not touch the edge of the pocket!</p>
<table style="border-collapse: collapse; width: 100%; height: 21px;" border="0">
<tbody>
<tr style="height: 21px;">
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/06/00caa1b4b7e7f0e52a2652767a228c72_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="USB Port overcurrent #13306 (FIONA)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/06/0f85fe99ce29ae9b2d2b9b17eeb6481d_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="USB Port overcurrent #13306 (FIONA)" alt="" width="399" height="299" loading="lazy" /></td>
</tr>
</tbody>
</table>
<p>If you are correcting the position of the bearings, make sure to keep the correct orientation. The tracks (rows of balls) have to be on the sides.</p>
<table style="border-collapse: collapse; width: 100%; height: 21px;" border="0">
<tbody>
<tr style="height: 21px;">
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/06/072a3e6a00466141e3159d45a529cf33_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="USB Port overcurrent #13306 (FIONA)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/06/6fbbf29a7f039d5a3ab1b2f2ebec8ec0_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="USB Port overcurrent #13306 (FIONA)" alt="" width="399" height="299" loading="lazy" /></td>
</tr>
</tbody>
</table>
<h4>xBuddy connection</h4>
<p>Check the motor connections on the board. For that, open the four screws that hold the xBuddy box cover. Make sure that the motor connector is not loose, and that the Y-axis motor connector has not been accidentally switched with the X-axis motor or any other motor.</p>
<table style="border-collapse: collapse; width: 100.026%;" border="0">
<tbody>
<tr>
<td style="width: 48.7906%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/10/9769d45d75346583db549d162dbb302b_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Homing error Y #13305 (MK4) #21305 (MK3.9)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.7906%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/10/a5df42079c5152c4bb1404adc18106ea.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Homing error Y #13305 (MK4) #21305 (MK3.9)" alt="" width="400" height="300" loading="lazy" /></td>
</tr>
</tbody>
</table>


Homing error Y #26305 (MK4S) #13305 (MK4) #21305 (MK3.9) #23305 (MK3.5)

<h3>What happened?</h3>
<p>The printer is showing the message "<strong>Hotend preheat error: Check the print head heater and thermistor wiring for potential damage</strong>"</p>
<p>Error name: Hotend preheat error</p>
<p>Error code: #26202 (MK4S) #13202 (MK4) #21202 (MK3.9)</p>
<p>This error is shown when the printer is unable to heat up the nozzle more than <strong>2 ºC for 20 seconds</strong>. The printer starts a safety feature, which instantly kills the heating process and displays the message on the screen. The printer then waits for the user to inspect all parts and if needed fix the issue.</p>
<h3>How to fix it?</h3>
<p>Make sure that the <strong>ambient temperature</strong> where the printer is is stable, and above <strong>10 ºC</strong>.</p>
<h4>Extruder inspection</h4>
<p>This error can be caused by any damage to the <strong>hotend heater</strong> or the <strong>hotend thermistor</strong>.</p>
<p>Access the LoveBoard and check the <span style="color: #843fa1;"><strong>heater</strong> </span>and <strong><span style="color: #236fa1;">thermistor</span></strong> cables. Make sure that they are connected correctly and that there is no damage along their length.</p>
<table style="border-collapse: collapse; width: 100%;" border="0">
<tbody>
<tr>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/04/4d8068ede1cb7f665960fe46fa065702.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Hotend preheat error #13202 (MK4)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/b1fcbf1f9cc8f479_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Preheat error #13202 (FIONA)" alt="" width="400" /></td>
</tr>
</tbody>
</table>
<h4>xBuddy board inspection</h4>
<p>On the MK4/MK3.9 main board, check if the <a href="http://help.prusa3d.com/article/blown-fuse-mk4-s-mk3-9-s_411666">fuse that protects the extruder</a> is not damaged.</p>
<p>Make sure that the Loveboard main cable is correctly connected to the xBuddy board.</p>
<h4>Multimeter check</h4>
<p>In case you have a multimeter available, use <a href="http://help.prusa3d.com/article/multimeter-usage_2117">this guide</a> to check the resistance on the hotend heater and the hotend thermistor.</p>


Hotend preheat error #26202 (MK4S) #13202 (MK4) #21202 (MK3.9)

<h3>What happened?</h3>
<p>The printer is showing the message <strong>"Check the heatbed heater &amp; thermistor wiring for possible damage."</strong></p>
<p>Error name: Bed preheat error</p>
<p>Error code: #26201 (MK4S) #13201 (MK4) #21201 (MK3.9) #23201 (MK3.5)</p>
<p>This message is shown when, during the preheat, the printer does not increase more than <strong>2 ºC for 20 seconds</strong>. The heating is paused so the issue can be fixed.</p>
<h3>How to fix it?</h3>
<p>Make sure that the <strong>ambient temperature</strong> where the printer is is stable, and above <strong>10 ºC</strong>.</p>
<p>This error can be caused by damage to either the <strong>heatbed thermistor</strong> or the <strong>heatbed power cable</strong>.</p>
<div class="tip-callout">Doing <strong>regular maintenance</strong> on the printer may prevent this type of issue.</div>
<p>On the heatbed, check the following:</p>
<ul>
<li>See if the <strong>thermistor </strong>is firmly seated below the <strong>Golden Kapton tape.</strong></li>
<li>Make sure that the <strong>washer </strong>is screwed above the round cable connector, not below it.</li>
<li>Check if the <strong>M3nN nut</strong> is holding the screw firmly.</li>
<li>Access the xBuddy board. Check the <strong><span style="color: #236fa1;">heatbed power cable</span></strong>, the <strong><span style="color: #2dc26b;">heatbed thermistor</span></strong>, and the <a href="http://help.prusa3d.com/article/blown-fuse-mk4-s-mk3-9-s_411666">fuse that protects the heatbed</a>.</li>
</ul>
<table style="border-collapse: collapse; width: 100%; height: 322.875px;" border="0">
<tbody>
<tr style="height: 301.875px;">
<td style="width: 48.8358%; height: 301.875px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/Heatbedthermistor.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Preheat error #13201 (FIONA)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.8358%; height: 301.875px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/b219085ec996c508.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Preheat error #13201 (FIONA)" alt="" width="400" height="300" loading="lazy" /></td>
</tr>
<tr style="height: 21px;">
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/30e875e9b027e87d.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Preheat error #13201 (FIONA)" alt="" width="400" height="1200" loading="lazy" /></td>
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/77686da340e7e4a3_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Preheat error #13201 (FIONA)" alt="" width="400" /></td>
</tr>
</tbody>
</table>
<p>In case all the items are correct, there might be an internal break in one of the cables. If you do not have a multimeter, it is possible to check the cables using the following test: </p>
<ol>
<li>Use a hairdryer to blow hot air at the heatbed.</li>
<li>While doing that, check if there is any temperature change on the LCD screen.</li>
<li>If there is a positive temperature change it means that the heatbed thermistor is working. In this case, the heater is defective.</li>
<li>If there is no change at all, the heatbed thermistor is defective.</li>
</ol>
<h4>Multimeter check</h4>
<p>In case you have a multimeter available, it is possible to check the resistance of the cables using the <a href="http://help.prusa3d.com/article/multimeter-usage_2117">Multimeter usage</a> guide.</p>


Bed preheat error #26201 (MK4S) #13201 (MK4) #21201 (MK3.9) #23201 (MK3.5)

<h3>What happened? </h3>
<p>The printer is showing the message: "<strong>Failed to home the extruder in Z-axis, make sure the loadcell is working</strong>".</p>
<p>Error name: Homing error Z</p>
<p>Error code: #26301 (MK4S) #13301 (MK4) #21301 (MK3.9)</p>
<h3>How to fix it? </h3>
<div>
<p>A fault in the <strong>Loadcell </strong>can trigger a homing error. Ensure that the printer is fully cooled down, go to <em>LCD Menu - Calibration - Diagnostics - Loadcell Test</em>. When tapping the nozzle, use a hard object for it. This is only to check if the Loadcell is responsive or not.</p>
<p>Make sure that the extruder is not exerting force to pull down the filament. If you are not sure, try to unwind it a small amount on the spool when testing the Z-axis.</p>
<p>In case you have an MMU, Enclosure, or custom setup where the filament is fed to the extruder by a PTFE tube, make sure that the extruder does not have to exert force to pull down the tube.</p>
<p>Check if the trapezoid nut has the correct orientation.</p>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/11/6641b70d816472324ff88cc18c0d2715_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Homing error Z #13301 (MK4) Z #21301 (MK3.9) (review)" alt="" width="400" height="300" loading="lazy" /></p>
<p>If no issues are found, open the side fan and make sure that the thumb screws that hold the heatbreak are not over-tightened. Always tighten these screws by hand, never with a tool.</p>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/10/5650cc936ba9fcf5c2cd4fa77f56a0dd_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Homing error Z #13301 (MK4) Z #21301 (MK3.9) (review)" alt="" width="400" height="300" loading="lazy" /></p>
<p>Also, try loosening the screws shown in the picture below, and re-tighten them, making sure that they are not over-tightened. After that, go to <em>LCD menu -&gt; Control -&gt; Run full selftest</em>.</p>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/10/fd9868db5993e185e1aff4b5161634dc_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Homing error Z #13301 (MK4) Z #21301 (MK3.9) (review)" alt="" width="400" height="300" loading="lazy" /></p>
</div>


Homing error Z #26301 (MK4S) #13301 (MK4) #21301 (MK3.9)

<h3>What happened?</h3>
<p>The Original Prusa MK4S/MK4/MK3.9/MK3.5 is equipped with a <strong>Power Panic</strong> feature. This feature can recover a print in case of a sudden power loss (read more about it <a href="http://help.prusa3d.com/article/power-panic_2092">here</a>). The power panic cable goes from the printer's PSU to the xBuddy board. In case there is any damage to the cable, the printer will show <strong>"Power panic has been detected during printer initialization. Inspect wiring of PP-cable."</strong></p>
<p>Error name: Power Panic</p>
<p>Error code: #26321 (MK4S) #13321 (MK4)  #20321 (MK3.9) #23321 (MK3.5)</p>
<h3>How to fix it?</h3>
<p>Check the connection of the cable both on the PSU and on the xBuddy board. Make sure that the cable is not damaged.</p>
<div class="note-callout">There are two versions of the power panic cable, one with only a black wire and one with black and white wires. Both are compatible with the MK4/S, MK3.9, and MK3.5, and there is no need to switch to one or the other.</div>
<div>
<table style="border-collapse: collapse; width: 100%; border-style: none;" border="0">
<tbody>
<tr>
<td style="width: 48.7906%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/08/3511cecf57c9cc5b14c140cd32c0bdee_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Power Panic #13321 (MK4)" alt="" width="395" height="296" loading="lazy" /></td>
<td style="width: 48.7906%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/08/1566eaf9ab8a2344560a6516c71d2673_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Power Panic #13321 (MK4)" alt="" width="395" height="1138" loading="lazy" /></td>
</tr>
</tbody>
</table>
</div>


Power Panic #26321 (MK4S) #13321 (MK4)  #21321 (MK3.9) #23321 (MK3.5)

<h3>What happened?</h3>
<p>The printer is showing the message <strong>"Check the print head thermistor wiring for possible damage."</strong></p>
<p>Error name: Hotend mintemp error</p>
<p>Error code: #26208 (MK4S) #13208 (MK4) #21208 (MK3.9)</p>
<p>This error is shown when the printer's nozzle temperature drops below <strong>5 ºC</strong> at any point. If this happens during a print, the print will be stopped.</p>
<h3>How to fix it?</h3>
<h4>Extruder inspection</h4>
<p>This error is usually caused by the <strong>hotend thermistor</strong>. </p>
<p>Access the LoveBoard. Check if the thermistor is connected correctly and if there is no damage along the cable length.</p>
<p>If you have a multimeter, it is possible to check the resistance of the cables to verify if they are damaged. For that, use our <a href="http://help.prusa3d.com/article/multimeter-usage_2117">Multimeter usage</a> guide.</p>
<table style="border-collapse: collapse; width: 100%;" border="0">
<tbody>
<tr>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/04/4d8068ede1cb7f665960fe46fa065702.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Hotend mintemp error #13208 (MK4)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/b1fcbf1f9cc8f479_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Maxtemp error #13206 (FIONA)" alt="" width="400" height="300" loading="lazy" /></td>
</tr>
</tbody>
</table>
<h4>xBuddy board inspection</h4>
<p>Make sure that the Loveboard main cable is correctly connected to the <strong>xBuddy board</strong>.</p>


Hotend mintemp error #26208 (MK4S) #13208 (MK4) #21208 (MK3.9)

<h3>What happened?</h3>
<p>The Original Prusa MK4/MK3.9/MK3.5 is showing the message: <strong>"Overcurrent detected on xBuddy heatbed port, disconnect the device."</strong></p>
<p>Error name: Heatbed Port Overcurrent</p>
<p>Error code: #26309 (MK4S) #13309 (MK4) #21309 (MK3.9) #23309 (MK3.5)</p>
<p>The error is shown when there is a damaged cable on the <strong>heatbed </strong>or any of its connections.</p>
<h3>How to fix it? </h3>
<p>The most likely cause of this issue is damage to the <strong>heatbed </strong>cable. Check the path between the heatbed and the <strong>xBuddy </strong>board, and see if there are any parts that are broken or pinched.</p>
<p>In case there is no damage, check the cable connection to the heatbed and to the xBuddy board. Try reconnecting the connectors.</p>
<p>In rare cases, this error message can be shown in case of damage to the xBuddy board. So if the cables and connectors are intact, try checking the board for any damage.</p>
<table style="border-collapse: collapse; width: 100%; height: 21px;" border="0">
<tbody>
<tr style="height: 21px;">
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/5bf0be529c827b33.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="USB Port overcurrent #13306 (FIONA)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.8358%; height: 21px;"> <img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/ca06837a757f0023_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Heatbed Port Overcurrent #13309 (FIONA)" alt="" width="399" height="299" loading="lazy" /></td>
</tr>
</tbody>
</table>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/a325d581e1a553bd_painted.jpeg" alt="" width="400" height="275" loading="lazy" /></p>


Heatbed Port Overcurrent #26309 (MK4S) #13309 (MK4) #21309 (MK3.9) #23309 (MK3.5)

<h3>What happened?</h3>
<p>The printer is showing the error "<strong>Hotend thermal runaway: Check the print head thermistor wiring for potential damage</strong>".</p>
<p>Error name: Hotend thermal runaway </p>
<p>Error code: #26204 (MK4S) #13204 (MK4) #21204 (MK3.9)</p>
<p>The error will show if the temperature on the nozzle drops by <strong>12 ºC</strong> for an extended period of time. This temperature drop would usually not be an issue, but if the heat is not recovered after <strong>60 seconds</strong> the error will happen. In this case, the printer will stop the heating and display the message on the screen.</p>
<h3>How to fix it? </h3>
<p>Make sure that the <strong>ambient temperature</strong> where the printer is is stable, and above <strong>10 ºC</strong>.</p>
<h4>Extruder inspection</h4>
<p>This error can be caused by any damage to the<strong> hotend heater</strong> or the <strong>hotend thermistor</strong>.</p>
<p>Make sure that the hotend thermistor is inserted in the heater block.</p>
<p>Access the LoveBoard. Check if the heater and the thermistor are connected correctly and if there is no damage along their length.</p>
<p>If you have a multimeter, you can use our <a href="http://help.prusa3d.com/article/multimeter-usage_2117">Multimeter usage</a> guide to check if the cables are damaged.</p>
<table style="border-collapse: collapse; width: 100%;" border="0">
<tbody>
<tr>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/04/4d8068ede1cb7f665960fe46fa065702.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Hotend thermal runaway #13204 (MK4)" alt="" width="400" height="300" loading="lazy" /></td>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/b1fcbf1f9cc8f479_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Thermal runaway #13204 (FIONA)" alt="" width="1600" height="1200" loading="lazy" /></td>
</tr>
</tbody>
</table>
<h4>xBuddy board inspection</h4>
<p>On the MK4/MK3.9 main board, check if the <a href="http://help.prusa3d.com/article/blown-fuse-mk4-s-mk3-9-s_411666"> fuse that protects the hotend</a> is not damaged.</p>
<p>Make sure that the Loveboard main cable is correctly connected to the xBuddy board.</p>


Hotend thermal runaway #26204 (MK4S) #13204 (MK4) #21204 (MK3.9)

<h3>What happened?</h3>
<p>The <strong>MK4S/MK4/MK3.9/MK3.5 xBuddy board</strong> is equipped with a safety mechanism to detect power supply overcurrent situations in the connection to the Multi-material unit (MMU). Upon detecting overcurrent, the printer automatically cuts off both power and communication to the MMU unit as a preventive measure against damage.</p>
<h3>I don't have an MMU installed</h3>
<p>If you haven't installed an MMU, make sure to disable the MMU functionality in the printer's menu in Settings -&gt; MMU Enable. However, if you still face this issue with the MMU option being turned off, it might indicate a damaged component on the xBuddy board. Please reach out to <a href="http://help.prusa3d.com/article/customer-support_2287">Customer support</a> for assistance.</p>
<h3>How to fix it?</h3>
<div class="note-callout">The MMU unit should not be connected or disconnected during regular use while the printer is running.</div>
<p>Inspect the <strong>MMU, Printer cable, and PD board</strong> for any signs of damage. Check the cable's path to the xBuddy board for any broken or pinched parts.</p>
<p>If there's no visible damage, ensure the cable connections to the MMU PDU and the xBuddy board are secure.</p>
<p>To troubleshoot, first disconnect the <strong><span style="color: #f1c40f;">MMU cable</span></strong> from the xBuddy board, go to the printer menu in <em>Settings -&gt; MMU Enable</em> and set the MMU to off. Verify if the printer operates correctly with the MMU unit disconnected and the MMU functionality turned off. After confirming this, reconnect the MMU and test the printer with the MMU turned on.</p>
<p>In rare cases, this error message might be shown due to a damaged xBuddy board. Try checking the board for any signs of damage.</p>
<div class="note-callout">When contacting <a href="http://help.prusa3d.com/article/customer-support_2287">Customer support</a> about this issue, it's crucial to specify not only what firmware and hardware are you using, but also the <strong>version of your printer's xBuddy board</strong> (e.g., 0.2.7 / v36, etc.), as there are variations in the electronic diagrams across different versions.</div>
<table style="border-collapse: collapse; width: 100%; height: 21px;" border="0">
<tbody>
<tr style="height: 21px;">
<td style="width: 50%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2024/02/14f3801e133f167c644feea2d7e8a601_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="MMU / Printer cable connected to the MMU3’s PD-board addon on the control board." alt="" width="1600" height="1200" loading="lazy" /></td>
<td style="width: 50%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2024/02/682bd0e96557fd37c8514dde88f4cc4a_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="MMU Overcurrent #13310 (MK4) #21310 (MK3.9)" alt="" width="400" height="300" loading="lazy" /></td>
</tr>
</tbody>
</table>
<h3>Technical information</h3>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2024/02/80b81dcc74f145ce57f9615b9accb7c6.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="MMU Overcurrent #13310 (MK4) #21310 (MK3.9)" alt="" width="600" height="373" loading="lazy" /></p>
<p>The xBuddy board is constantly monitoring the current flowing through the electronics. If the power draw exceeds 3.6A on the MMU connector's power line, the printer will display this error, and the corresponding LED indicator on the xBuddy board will illuminate. A potential overcurrent condition is likely to occur after the first startup, as power demand peaks while capacitors are charging. </p>
<p>The xBuddy board is designed with the capability to fully manage power delivery to the MMU unit, incorporating a software feature to mitigate such overcurrent scenarios. However, this function is specifically calibrated for the original MMU3 unit. In certain unsupported hardware configurations, this may result in a false error indication.</p>


MMU Overcurrent #26310 (MK4S) #13310 (MK4) #21310 (MK3.9) #23310 (MK3.5)

<h3>What happened?</h3>
<p>On the Original Prusa MK4/MK3.9/MK3.5, the I2C bus is used for the <strong>xBuddy</strong> board to communicate with other printer components. If there is an error in sending data from the xBuddy board, the printer will show the message: <strong>"HAL detected an I2C error when sending data via I2C."</strong></p>
<p>Error name: I2C Send failed</p>
<p>Error code: #26311 (MK4S) #13311 (MK4) #21311 (MK3.9) #23311 (MK3.5)</p>
<h3>How to fix it? </h3>
<p><strong>Restarting the printer</strong> is expected to resolve the error, and this is not expected to occur again. In case a restart does not resolve it, please contact our <a href="http://help.prusa3d.com/article/customer-support_2287">customer support</a>, we will take it from here. </p>


I2C Send failed #26311 (MK4S) #13311 (MK4) #21311 (MK3.9) #23311 (MK3.5)

<h3>What happened?</h3>
<p>On the Original Prusa MK4S/MK4/MK3.9/MK3.5, the I2C bus is used for the <strong>xBuddy</strong> board to communicate with other printer components. If there is an error while the xBuddy board is receiving data, the printer will show the message: <strong>"HAL detected an I2C error when receiving data via I2C."</strong></p>
<p>Error name: I2C Receive Failed</p>
<p>Error code: #26315 (MK4S) #13315 (MK4) #21315 (MK3.9) #23315 (MK3.5)</p>
<h3>How to fix it? </h3>
<p><strong>Restarting the printer</strong> is expected to resolve the error, and this is not expected to occur again. In case a restart does not resolve it, please contact our <a href="http://help.prusa3d.com/article/customer-support_2287">customer support</a>, we will take it from here. </p>


I2C Receive Failed #26315 (MK4S) #13315 (MK4) #21315 (MK3.9) #23315 (MK3.5)

<h3>What happened?</h3>
<p>The printer is showing the message <strong>"Check the heatbed thermistor wiring for possible damage."</strong></p>
<p>Error name: Bed thermal runaway </p>
<p>Error code: #26203 (MK4S) #13203 (MK4) #21203 (MK3.9) #23203 (MK3.5)</p>
<p><strong>Thermal Runaway</strong> is a safety feature designed to cut power to the heaters in case of a cable malfunction. If your printer's thermistor somehow dislodges itself, electronic parts can get a lower (incorrect) temperature reading. In an attempt to compensate for the lower temperature, the heater could reach dangerously high temperatures.</p>
<p>If the <strong>heatbed </strong>temperature drops by more than <strong>2 ºC</strong> for over<strong> 60 seconds</strong>, the printer will shut down the print and show the Thermal Runaway error.</p>
<h3>How to fix it?</h3>
<p>Make sure that the ambient temperature is above <strong>10 ºC</strong>, and that there are <strong>no sources of cooling</strong> near the printer, like air conditioning or windows.</p>
<p>Check if the thermistor is well secured under the <strong>golden Kapton tape</strong>.</p>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/Heatbedthermistor.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Thermal runaway #13203 (FIONA)" alt="" width="600" height="450" loading="lazy" /></p>
<p>If you are printing small objects with high-temperature filaments, try to print multiple at once and/or place them away from the center of the heatbed.</p>
<p>Open the <strong>xBuddyBox-cover</strong> and the <strong>el-box-cover</strong> by opening the screws indicated below to access the heatbed cables. Make sure that the heatbed power cable did not slip from the screw, and that the heatbed thermistor cable is well connected.</p>
<p>If you have a multimeter, you can check the resistance of the cables using this guide: <a href="http://help.prusa3d.com/article/multimeter-usage_2117">Multimeter usage</a>.</p>
<table style="border-collapse: collapse; width: 100%;" border="0">
<tbody>
<tr>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/ef0adcc4ba6782d2_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Thermal runaway #13203 (FIONA)" alt="" width="400" height="267" loading="lazy" /></td>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/783109cb80ab5ceb_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Thermal runaway #13203 (FIONA)" alt="" width="400" height="267" loading="lazy" /></td>
</tr>
</tbody>
</table>
<h3> </h3>


Bed thermal runaway #26203 (MK4S) #13203 (MK4) #21203 (MK3.9) #23203 (MK3.5)

<h3>What happened?</h3>
<p>The Original Prusa MK4S/MK4/MK3.9 is equipped with a <strong>loadcell</strong>, to detect that the nozzle is close enough to the steel sheet for printing, and to avoid damage that would be caused by the nozzle digging into the steel sheet. </p>
<p>The printer firmware expects a measurement sample from the loadcell to occur within a specified time. In case this does not happen, the printer will show the message <strong>"There was a timeout while waiting for measurement sample, please repeat the action."</strong></p>
<p>Error name: Loadcell Timeout</p>
<p>Error code: #26528 (MK4S) #13528 (MK4) #21528 (MK3.9)</p>
<h3>How to fix it?</h3>
<p>First, make sure you have the <a href="http://help.prusa3d.com/article/how-to-update-firmware-mk4-s-mk3-9-s-mk3-5-s-xl_453086">latest firmware</a>.</p>
<h4>A visual inspection</h4>
<div class="warning-callout">Before you start, make sure:</p>
<ul>
<li>the filament is unloaded from the extruder</li>
<li>the printer is turned OFF and unplugged from electricity</li>
<li>the hotend and the heatbed are cooled down to ambient temperature</li>
</ul>
</div>
<p>Access the LoveBoard, locate the loadcell connector and cable, and check for any loose cable, disconnected cable, or visible damage. The loadcell connector is indicated with the orange arrow in the picture below. </p>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/04/98f9151af765084ab2be69a52d63f20c_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Loadcell Not Calibrated #13523 (FIONA)" alt="" width="500" height="375" loading="lazy" /></p>
<h4>Remake the loadcell test</h4>
<div class="warning-callout">Do not manipulate or touch the printer unless the instructions on the printer screen prompt you to do so.</div>
<div>
<p>Navigate to <em>LCD Menu - Calibration - Diagnostics - Test Loadcell</em> to restart the loadcell test. </p>
<p>During the test, you will be asked to tap the nozzle at a specific time, and a progress bar on top of the screen will be filled. If the progress bar is not filled or the printer shows any errors, please contact our <a href="http://help.prusa3d.com/article/customer-support_2287">customer support</a>.</p>
</div>


Loadcell Timeout #26528 (MK4S) #13528 (MK4) #21528 (MK3.9)

<h3>What happened?</h3>
<p>The printer is showing  the message <strong>"Check the heatbed thermistor wiring for possible damage."</strong></p>
<p>Error name: Bed mintemp error </p>
<p>Error code: #26207 (MK4S) #13207 (MK4) #21207 (MK3.9) #23207 (MK3.5)</p>
<p>This error is shown when the heatbed temperature drops below <strong>5 ºC</strong> at any time. This error can also happen when the printer is idle and not heated.</p>
<h3>How to fix it?</h3>
<p>Make sure that the <strong>ambient temperature</strong> where the printer is is stable, and above <strong>10 ºC</strong>.</p>
<p>This error is usually caused by a damaged <strong>heatbed thermistor</strong>.</p>
<div class="tip-callout">Doing regular maintenance on the printer may prevent this type of issue.</div>
<p>Check if the thermistor is well secured under the <strong>golden Kapton tape</strong>.</p>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/Heatbedthermistor.jpg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Maxtemp error #13205 (FIONA)" alt="" width="500" height="375" loading="lazy" /></p>
<p>In order to test if the thermistor is damaged, go to the printer menu in <em>Settings -&gt; Temperature -&gt; Heatbed temperature</em>, and set it to <strong>80 ºC</strong>. Then, move the heatbed cables by hand and see if the temperature will fluctuate. If the temperature fluctuates more than <strong>5 ºC</strong>, from the set temperature, the thermistor needs to be replaced.</p>
<p>Open the <strong>xBuddyBox-cover</strong> and the <strong>el-box-cover</strong> by opening the screws indicated below to access the heatbed cable connectors. Make sure that the heatbed power cable did not slip from the screw, and that the heatbed thermistor cable is well connected.</p>
<p>If you have a <strong>multimeter</strong>, you can check the resistance of the cables using this guide: <a href="http://help.prusa3d.com/article/multimeter-usage_2117">Multimeter usage</a></p>
<table style="border-collapse: collapse; width: 100%;" border="0">
<tbody>
<tr>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/ef0adcc4ba6782d2_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Thermal runaway #13203 (FIONA)" alt="" width="400" height="267" loading="lazy" /></td>
<td style="width: 48.8358%;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2023/03/783109cb80ab5ceb_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Thermal runaway #13203 (FIONA)" alt="" width="400" height="267" loading="lazy" /></td>
</tr>
</tbody>
</table>
<h3> </h3>


Bed mintemp error #26207 (MK4S) #13207 (MK4) #21207 (MK3.9) #23207 (MK3.5)

<h3>What happened?</h3>
<p>The Original Prusa MK4/MK3.9 is showing the message: <strong>"Overcurrent detected on nozzle heater."</strong></p>
<p>Error name: Nozzle Heater Overcurrent</p>
<p>Error code: #26308 (MK4S) #13308 (MK4) #21308 (MK3.9)</p>
<p>The error is shown when there is a damaged cable on the <strong>hotend heater</strong> or any of its connections.</p>
<h3>How to fix it? </h3>
<p>The most likely cause of this issue is damage to the <span style="color: #e67e23;"><strong>hotend heater cable</strong></span>. Check the path between the hotend heater and the <strong>LoveBoard</strong>, and see if there are any parts that are broken or pinched.</p>
<p>In case there is no damage, check the <span style="color: #169179;"><strong>cable connection</strong></span> to the LoveBoard board. Try reconnecting the cable to its connector.</p>
<p>In rare cases, this error message can be shown in case of damage to the <strong>LoveBoard</strong>, or to the <strong>xBuddy </strong>board. So if the cables and connectors are intact, check the boards for any visible damage.</p>
<div class="warning-callout"><strong>Always touch the sides of the electronic board while manipulating it</strong>. Avoid touching the chips, capacitors, and other parts of the electronics.</div>
<table style="border-collapse: collapse; width: 100%; height: 21px;" border="0">
<tbody>
<tr style="height: 21px;">
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2024/02/ee31e46f11f620d2cae4fbd2c355251c_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Nozzle Heater Overcurrent #13308 (MK4) #21308 (MK3.9)" alt="" width="395" height="296" loading="lazy" /></td>
<td style="width: 48.8358%; height: 21px;"><img decoding="async" src="https://cdn.help.prusa3d.com/wp-content/uploads/2022/10/0204b8e0105d056d_painted.jpeg" alt="" width="399" height="299" loading="lazy" /></td>
</tr>
</tbody>
</table>
<p><img decoding="async" style="display: block; margin-left: auto; margin-right: auto;" src="https://cdn.help.prusa3d.com/wp-content/uploads/2024/02/c3f6dfae25bc4baf6e644c11c7eeac10_painted.jpeg" sizes="(min-width: 1024px) 820px, 100vw" srcset="Nozzle Heater Overcurrent #13308 (MK4) #21308 (MK3.9)" alt="" width="500" height="375" loading="lazy" /></p>


Nozzle Heater Overcurrent #26308 (MK4S) #13308 (MK4) #21308 (MK3.9)

<h3>What happened?</h3>
<p>When flashing the firmware on your Original Prusa MK4, MK3.9, or MK3.5, you might get the message "<strong>Firmware file missing in the USB flash!</strong>".</p>
<p>Error name: No FW on USB flash drive</p>
<p>Error code: #26604 (MK4S) #13604 (MK4) #21604 (MK3.9) #23604 (MK3.5)</p>
<p>This error happens when you attempt flashing firmware on the printer, but the printer does not find any firmware in the USB drive that can be uploaded to the printer.</p>
<h3>How to fix it?</h3>
<p><a href="https://help.prusa3d.com/downloads">Download the firmware</a> and if necessary the bootloader, and transfer it to your USB drive. Make sure to unmount the drive from your operating system before physically removing it.</p>
<p>Insert the USB drive back into the printer and reboot the printer using the reset button directly next to the knob to initiate the flashing procedure. In case the procedure does not start, reboot the printer again by pressing the same reset button, and while the printer is booting up, press once the rotating knob.</p>
<p>If the issue persists, the problem might be in the USB flash drive. Find any other USB drive in your household, make sure it is formatted to FAT32, copy both firmware files and repeat the previously described procedure.</p>
<div class="tip-callout">Are you still having issues? Contact our <a href="http://help.prusa3d.com/article/customer-support_2287">support team</a> and let them know that you tried to fix the issue with these instructions. We will take it from there.</div>


No FW on USB #26604 (MK4S) #13604 (MK4) #21604 (MK3.9) #23604 (MK3.5)

<h3>What happened?</h3>
<p>During firmware flashing on your Original Prusa MK4, MK3.9, or MK3.5, you might get the message "<strong>USB drive not connected! Please insert a USB drive with a valid firmware file</strong>".</p>
<p>Error name: USB not connected</p>
<p>Error code: #26602 (MK4S) #13602 (MK4) #21602 (MK3.9) #23602 (MK3.5)</p>
<p>This issue happens when there is an error reading the USB drive.</p>
<h3>How to fix it?</h3>
<p>Make sure that the USB drive is connected to the printer, and that the USB port in the mainboard is not damaged. If the error persists, try using a new, <a href="https://help.prusa3d.com/article/sd-cards-and-usb-drives_112291#how-do-i-format-the-usb-drive-sd-card" target="_blank" rel="noopener">FAT32-formatted USB drive</a>. </p>
<div class="tip-callout">Are you still having issues? Contact our <a href="http://help.prusa3d.com/article/customer-support_2287">support team</a> and let them know that you tried to fix the issue with these instructions. We will take it from there.</div>


USB not connected #26602 (MK4S) #13602 (MK4) #21602 (MK3.9) #23602 (MK3.5)


<ul>
<li>New Arrange tool options</li>



<li>New Cut tool options</li>



<li>Per-symbol text projection on surface</li>



<li>Interlocking of painted areas for MMU printing</li>
</ul>


2.6.1


<ul>
<li>Input Shaper and Pressure Advance</li>



<li>PrusaSlicer 2.6.0 and print profiles</li>



<li>G-code compatibility</li>



<li>Support for MK3.9</li>



<li>Language translations</li>



<li>Bug fixes</li>
</ul>


5.0.0


<p>Updated with instructions for MK3.9 upgrade</p>


1.03


<ul>
<li>Changes to self-test</li>



<li>Extended Connect Wizard</li>



<li>Timeout for G-code M115</li>



<li>Updated bootloader</li>



<li>Fixed bugs</li>
</ul>


5.0.1


<ul>
<li>New SVG support</li>



<li>Binary G-Code (.bgcode) export support + conversion</li>



<li>Arc fitting support </li>
</ul>


2.7.0


<ul>
<li>Printing speed boost with Input Shaper and Pressure Advance (XL and MINI)</li>



<li>Major updates to network code; Instant Printing feature</li>



<li>Major updates to Prusa Connect and network communication</li>



<li>Introducing a new efficient open-source Binary G-code format</li>



<li>New useful pre-print screen for XL Multi-Tool printers</li>



<li>Cancel object directly from the printer’s menu</li>
</ul>


5.1.0


<ul>
<li>Binary G-code settings</li>



<li>Wipe tower weight</li>



<li>Bug fixes</li>
</ul>


2.7.1


<ul>
<li>Sending crash dumps to Tech support</li>



<li>New bootloader 2.3.4</li>



<li>Firmware flashing updated</li>



<li>Bug fixes</li>
</ul>


5.1.2


<ul>
<li>Printer type check on startup</li>
</ul>


5.1.3


<ul>
<li>Improvements to multi-material printing</li>



<li>Vase mode smoothing</li>



<li>Support for 3MF files generated in BambuStudio</li>



<li>Metadata with boundary polygon of each object</li>
</ul>


2.7.3


<ul>
<li>Objects from 3MFs generated by BambuStudio now retain multimaterial painting when loaded</li>



<li>Fixed a bug where downloading files from Printables did not work when enabled in Preferences</li>
</ul>


2.7.4


<ul>
<li>Touch support</li>



<li>Stuck filament detection</li>



<li>Stealth mode</li>



<li>MMU3 support</li>



<li>MMU3 firmware auto-update</li>



<li>Cold Pull</li>



<li>Time Zone settings updated</li>



<li>Improvements by the Prusa community</li>



<li>Bug fixes</li>
</ul>


6.0.0


<ul>
<li>Japanese language support (MK4, MK3.9, MK3.5, XL)</li>



<li>Nozzle cleaning repaired (MK4, MK3.9, XL)</li>



<li>Acceleration limit restored (MK4, MK3.9, MINI)</li>



<li>Stealth mode corrected (MK4, MK3.9, MK3.5, XL)</li>
</ul>


6.0.1


<ul>
<li>Improvements by Prusa community</li>
</ul>


6.0.2


<ul>
<li>Interim solution of USB disconnect issues (MK4, MK3.9, MK3.5, XL)</li>
</ul>


6.0.3


<ul>
<li>Prusa Connect integration</li>



<li>Prusa Account integration</li>



<li>Improved UI</li>



<li>Improved G-code Viewer</li>



<li>New system profile updating system</li>



<li>Single Perimeter for top and bottom layers</li>



<li>Extended SLA layer separation configuration</li>



<li>Bug fixes</li>
</ul>


2.8.0

6.0.4


<ul>
<li>Support for MK3.9S and MK3.5S printers</li>



<li>Numeric keyboard</li>



<li>Custom names for steel sheet</li>



<li>User-configurable hostname</li>



<li>Binary G-code check</li>



<li>ESP firmware flash during boot (MINI, MK3.5/S, MK3.9/S, MK4/S)</li>



<li>New bootloader 2.3.5</li>



<li>Network Status screen</li>



<li>Steel sheet name in footer (MK3.5/S)</li>



<li>Powered Z-motors during calibration procedure (MK3.5/S, MK3.9/S, MK4/S)</li>



<li>Default nozzle diameter set to 0.4 (XL)</li>



<li>Bug fixes</li>
</ul>


6.1.2


<ul>
<li>Issues with numeric keyboard repaired (MK4/S, MK3.9/S, MK3.5/S, XL)</li>



<li>Returned nozzle diameter setup (XL)</li>



<li>Printhead position during calibrations changed (MK4/S, MK3.9/S, MK3.5/S)</li>



<li>Cold pull (XL)</li>
</ul>


6.1.3


<ul>
<li>Improved menu bar, the menu no longer hides under a button</li>



<li>Two new parameters (Abrasive material and High flow nozzle) for G-Code checks</li>



<li>Improved automatic orientation of bridges</li>



<li>Number of bugfixes</li>
</ul>


Original Prusa MK3.9

Articles