JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

How to replace a heatbed tile and a heatbed tile cable (XL)

Menu

How to replace a heatbed tile and a heatbed tile cable (XL)

How to replace a heatbed tile and a heatbed tile cable (XL)
Relevant for:
XL
Last updated 4 months ago
How to replace a heatbed tile and a heatbed tile cable (XL)
 Difficulty
Easy
 Steps
10
 Available languages
ENCSPLDEESITFR

Step 1 Introduction

Introduction
Introduction
Introduction
⬢This guide will take you through the replacement of a heatbed tile and its cable on the Original Prusa XL.
The following instructions are compatible with all Original Prusa XL versions.
⬢All necessary parts are available in our shop prusa3d.com.
Note that you have to be logged in to have access to the spare parts section.

Step 3 Preparing the printer

Preparing the printer
Preparing the printer
Preparing the printer
⬢Auto-home the printer, navigating to Control ->Autohome.
⬢Lower the heatbed slightly from the auto-home position. Navigate to Control ->Move Axis ->Move Z and turn the knob to move the axis.
If the printer is heated, cool down the printer. Navigate to Control ->Temperature ->Cooldown. Wait for the printer to fully cool down.
⬢Turn the power switch OFF (symbol "O").
⬢From the rear side of the printer, unplug the PSU cable.
⬢プリントシートを取り外します。

Step 4 Disconnecting the heatbed tile cable

Disconnecting the heatbed tile cable
Disconnecting the heatbed tile cable
Disconnecting the heatbed tile cable
Disconnecting the heatbed tile cable
The Modular Bed board is located below the heatbed, and it is covered by bed-controller-case. Each heatbed tile is connected to the Modular Bed by a cable.
⬢The bed-controller-case has engraved numbers under the corresponding heatbed tile cable, with 8 cables per each side.
Locate the heatbed tile cable based on the number of the heatbed tile.
Each connector has a safety latch. It is necessary to press the latch before disconnecting. Otherwise, the connector may get damaged.
⬢In case of a heatbed tile cable replacement, disconnect the cable from the Modular Bed board.
⬢The heatbed tiles are numbered as shown in the picture.
⬢From the Modular Bed board side, disconnect the cable associated with the heatbed tile that will be replaced.

Step 5 Removing the heatbed tile

Removing the heatbed tile
Removing the heatbed tile
Removing the heatbed tile
Each heatbed tile is held in place from the bottom by four screws. Identify the ones holding the heatbed tile that will be replaced.
⬢Using the TX 8 Allen key, loosen the four M3x10rT screws that hold the heatbed tile in place, together with their M3 washers.
Do not throw away the screws and the washers! We will use them later.
⬢Remove the heatbed tile and place it away. In the example picture, the heatbed tile 7 is removed.

Step 9 Testing the printer

Testing the printer
Testing the printer
Testing the printer
⬢From the rear side, plug in the power cable.
⬢Turn the power switch ON (symbol "I").
⬢Set a temperature to the entire modular bed, navigating to Control -> Heatbed temperature, and see if the temperature raises regularly.

Step 10 It's done

It's done
It's done
⬢That's it, good job! You just successfully replaced the heatbed tile on the Original Prusa XL.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us