⬢This guide will take you through the replacement of the blower fan on the Original Prusa SL1S SPEED.

⬢All necessary parts are available in our shop shop.prusa3d.com

Note that you have to be logged in to have access to the spare parts section.

⬢2.0mm Allen key

⬢2.5 mm 六角レンチ

⬢Cutting pliers

⬢Cardboard or similar soft pad (e.g. a piece of cloth)

⬢Small bowl or box for storing fasteners. Some fasteners are very small and can be lost.

For a better handling, it is recommended to prepare a clean workbench with a space of at least 1 m x 1 m (40 in x 40 in). With access from two sides or more.

We're recommending a bright light above your workbench. Some parts inside the printer are dark and inadequate light could make a very difficult procedure.

⬢Turn the left side of the printer towards you.

⬢Locate, release and remove the four screws. Keep the screws safely in a bowl or box. You will need them later on.

⬢Turn the printer by 180° and remove the last four screws on the other side.

⬢Slide the cover just a few cm/inches out.

There are two designs of USB and power button:

⬢Locate the blower fan cable (black-red-yellow wires). Press the safety pin on the connector and disconnect the blower fan from the electronics board (left side of the printer). Do not pull out the connector without pressing the pin, it may damage the connector or the board.

⬢Leave the cable free for now.

⬢Release all eight screws on the bottom of the printer. Store these screws

⬢Carefully remove the UV LED fan from the printer. Put it next to the printer. No need to disconnect the fan cable.

⬢Look into the opening at the bottom of the printer slightly from above and locate the cable bundle.

⬢Push the blower fan cable through the gap between the electronics board and the base of the printer. Guide the cable to the right side of the printer and keep it free for now.

⬢Release and remove the screw on the right side of the support.

⬢Hold the blower fan with your hand and release the screw on the left side of the support.

⬢Carefully put the blower fan assembly next to the printer.

⬢Look from the right side and see if your printer has a zip tie on the cable bundle that includes the blower fan cable. Cut the zip tie. AVOID CUTTING CABLES!!!

⬢Remove the blower fan cable from the printer.

⬢Turn the blower fan assembly and remove two screws from the blower (printed part).

⬢Turn the blower to the previous position and tear apart the blower (printed part) and the blower fan.

⬢There are two different versions of the blower fan mounting. Select your version and follow the appropriate steps:

⬢Release and remove two screws securing the blower fan.

⬢Pull out the blower fan from the two columns on the blower fan holder.

⬢Push the blower fan cable through the hole in the blower fan holder and put the blower fan away. You will no longer need this one.

⬢Now, go to New blower fan: parts preparation

⬢From the back of the blower fan assembly release two screws securing the fan.

⬢Push the fan cable through the blower fan holder back to the fan.

⬢Place the blower fan away. You will no longer need this one.

⬢New blower fan (1x)

⬢Blower fan gasket (1x)

⬢Keep prepared the rest of the previously removed screws. In the following steps, you will be prompted to use them.

⬢Clean the top surface of the blower fan (the side with the turbine), before you apply the gasket. It is recommended to use IPA and cleaning wipes or paper towels.

⬢Remove the center part of the gasket, you will need just the outer "rim".

⬢Peel off the protective film (paper).

⬢Place the gasket on the fan as in the picture, with the glue facing down. Press it all around to ensure full contact between the gasket and the fan.

⬢This step is for the new version of the fan mounting. For the old version, go to Assembling the new blower fan (old version).

⬢Place the fan and the fan holder like in the picture. See the arrows to ensure correct orientation of the fan.

⬢Guide the cable through the hole.

⬢Place the fan on the columns and slide it carefully all the way down. Try to push equally to ensure the fan is always levelled.

⬢Secure the fan using two M3x20r screws. Tighten them very carefully, or you might break the fan's casing.

⬢Now, go to Installing the blower

⬢Place the fan and the fan holder like in the picture. See the arrows to ensure correct orientation of the fan.

⬢Guide the cable through the hole.

⬢Turn the assembly around and insert two screws M5x10r (previously M5x16r). Tighten them very carefully, or you will break the fan's casing.

⬢Prepare the blower (printed part) and check if both M3nS nuts didn't fall out from the part. If so, insert them back into the holes in the plastic part. To insert the nuts, you can  follow these instructions.

⬢Grasp the blower fan and blower as shown and point them at each other.

⬢Slide both parts together. Make sure there is no gap between them.

⬢Turn the assembly. Insert and tighten two M3x5 screws (that you removed earlier) into the plastic part and secure both parts together.

⬢Insert the blower fan assembly into the printer. The metal sheet (fan holder) has to be located behind the support bar.

⬢Hold the assembly by your hand and secure it with the M3x10b countersunk screw through the left screw hole.

⬢Insert and tighten the second M3x10b countersunk screw in the right screw hole.

⬢Guide the blower fan cable like in the picture.

⬢Take the blower fan cable connector and guide it inside the printer along the cable bundle.

⬢From the opening on the bottom of the printer, take the blower fan cable and carefully pull it out. It is not necessary to pull the entire cable length. Suffice as much as you see in the picture.

⬢Guide the cable inside the printer and push it thought the gap between the electronics board and the base of the printer. Guide the cable out to the electronics.

⬢Connect the blower fan cable connector to the empty slot on the electronics board.

⬢Push all the cables inside the printer down as much as possible. There must be no cable in the UV LED fan area.

⬢Gather as much UV LED cable as possible on the left side of the printer. Push the cable as far as the edge of the opening.

⬢Close the UV LED fan. Avoid pinch the UV LED fan cable!

⬢Make sure you do not pinch the cable by making sure that the cover is flush with the surface of the printer.

⬢Align the holes after closing the UV LED fan.

⬢Secure the UV LED fan by tightening eight M3x5b countersunk screws, that you removed earlier.

⬢Now you can carefully put the printer back on its feet.

⬢Slide the cover halfway to the printer and stop, we need to connect the front USB and power button first.

⬢NEW DESIGN: Look from above in the front cover and connect the USB & Power cable. Make sure the safety pin "clicks".

⬢OLD DESIGN: Connect the power cable button to the extension cable. Make sure the safety pin "clicks".

⬢Slide the cover onto the printer and secure it on one side using two M3x5b countersunk screws. Don't tighten them firmly yet. Move to the other side and repeat the procedure.

⬢As soon as the cover is aligned and partly secured, add the remaining  screws and tighten them all on both sides.

⬢Turn the printer around.

⬢Slide the cover onto the printer and secure it on one side using two M3x5b countersunk screws. Don't tighten them firmly yet. Move to the other side and repeat the procedure.

⬢As soon as the cover is aligned and partly secured, add the remaining  screws and tighten them all on both sides.

⬢Plug the printer and turn it ON.

⬢On the touch screen navigate to Home -> Settings -> Calibration -> Selftest.

⬢Run the Selftest and follow the instructions on the screen.

⬢The Selftest takes only a few minutes and will need user interaction. If no error message is displayed during the Selftest, everything is OK.