JA
  • English
  • Čeština
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

How to set up a Buddy Cam

Menu

How to set up a Buddy Cam

How to set up a Buddy Cam
Relevant for:
XL
Last updated 10 days ago
How to set up a Buddy Cam
 Difficulty
Very easy
 Steps
9
 Available languages
ENCSPLDEITFR

Step 1 Introduction

Introduction
Introduction
Introduction
⬢This guide will take you through the installation of the Buddy3D camera mount on your Original Prusa XL.
Before starting, ensure you have printed all the necessary parts.
The printed parts can be found on Printables.com.
⬢If you are installing the camera in an Enclosure, proceed to the XL+ENC: parts preparation

Step 2 XL: parts preparation

XL: parts preparation
XL: parts preparation
XL: parts preparation
XL: parts preparation
⬢For this guide, please prepare:
⬢Fixing-card (1x)
⬢M3x10 screw (3x)
⬢Frame-clip (2x)
⬢XL-Cam-holder (1x)
⬢XL-frame-holder (1x)

Step 3 CoreXY & frame holder preparation

CoreXY & frame holder preparation
CoreXY & frame holder preparation
CoreXY & frame holder preparation
⬢Attach the XL-cam-holder to the XL-frame-holder and secure it with one M3x10 screw using a 2.5 mm Allen key. Do not overtighten the screw!
⬢Using a T10 Torx screwdriver, remove the M3x8bT from the frame. Don't throw the screw away!

Step 4 Frame clip preparation

Frame clip preparation
Frame clip preparation
Frame clip preparation
Frame clip preparation
⬢From the outside of the right XY core, insert one frame-clip into the extrusion and rotate it by 90° clockwise. Hint: use the Needle-nose pliers to rotate the frame-clip.
⬢Insert the second frame-clip with the same process.
⬢Using a fixing-card, align the frame-clips on the left side of the extrusion.

Step 5 Frame holder securing

Frame holder securing
Frame holder securing
Frame holder securing
Frame holder securing
⬢Attach the prepared XL-frame-holder and attach it onto the frame-clips.
⬢Secure the XL-frame-holder with two M3x10 using a 2.5 mm Allen key. Do not overtighten the screws!
⬢Insert and secure the M3x8bT screw using a T10 Torx screwdriver. Do not overtighten the screw!

Step 6 Buddy cam securing

Buddy cam securing
Buddy cam securing
Buddy cam securing
Buddy cam securing
⬢Align the Buddy3D cam with the XL-cam-holder as in the picture.
⬢While holding the XL-frame-holder from the right side, attach the Buddy cam to the XL-cam-holder.
⬢Turn the Buddy3D cam 90° clockwise to secure it in its position.
⬢Connect the camera with a USB-C cable.

Step 7 XL+ENC: parts preparation

XL+ENC: parts preparation
XL+ENC: parts preparation
⬢次のステップのために、次のものをご用意ください：。
⬢XL-ENC-frame-holder (1x)
⬢M3x10 screw (3x)
⬢XL-Cam-holder (1x)

Step 8 Frame holder securing

Frame holder securing
Frame holder securing
Frame holder securing
Frame holder securing
⬢Attach the XL-cam-holder to the XL-ENC-frame-holder and secure it with one M3x10 screw using a 2.5 mm Allen key. Do not overtighten the screw!
⬢Open the lid.
⬢Attach the prepared XL-ENC-frame-holder to the upper left corner inside the XL Enclosure.
⬢Secure the XL-ENC-frame-holder with two M3x10 screws using a 2.5 mm Allen key. Do not overtighten the screw!

Step 9 Buddy cam securing

Buddy cam securing
Buddy cam securing
Buddy cam securing
⬢Align the Buddy3D cam with the XL-cam-holder as in the picture.
⬢Attach the Buddy3D cam to the XL-cam-holder and turn the Buddy3D cam 90° clockwise to secure it in its position.
⬢Connect the camera with a USB-C cable.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us