LCD menu (CORE One INDX) | Prusa Knowledge Base

The Prusa CORE One with INDX upgrade is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

For the versions of the CORE One without INDX, go to LCD menu (CORE One/+) [進行中の翻訳].

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

Make sure to always have the latest latest firmware.

Print
Preheat
- - PLA
  - PETG
  - ASA
  - PC
  - PVB
  - ABS
  - HIPS
  - PP
  - FLEX
  - PA
  - Custom
    - - Name
      - Nozzle temperature
      - Nozzle Preheat Temperature
      - Bed Temperature
      - Nominal Chamber Temperature
      - Minimum Chamber Temperature
      - Maximum Chamber Temperature
      - Is Abrasive
      - Requires Filtration
      - Confirm
  - Show All
  - Cooldown
Filament
- - Empty nozzle cleaner
  - Load filament
  - Unload filament
  - Change filament
  - Purge filament
  - Change Filament in All Tools
  - Manage Filaments
    - - Loaded filaments
      - Edit Filaments
      - Reorder Filaments
      - Enable Filaments
Control
- - Pick/Park Tool
    - - Park Current Tool
      - Pick Tool #
  - Move axis
    - - Move X
      - Move Y
      - Move Z
      - Move E
      - Cooldown
  - Temperature
    - - Nozzle # temperature
      - Heatbed temperature
      - Chamber temperature
      - Print fan speed
      - Dock fan
      - Chamber fans
      - Chamber fans limit
      - Filtration fan
      - Cooldown
  - Autohome
  - Set ready
  - Disable motors
  - Release stuck nozzle
  - Calibrations & Tests
    - - 1 Door sensor
      - 2 X Axis Test
      - 3 Y Axis Test
      - 4 Z Alignment Calibration
      - 5 Belt tuning
      - 6 Homing Calibration
      - 7 Dock Calibration
      - 8 Loadcell Test
      - 9 Z Axis Test
      - 10 Fan Test
      - 11 Heater Test
      - 12 Tool Offset Calibration
      - 13 Nozzle Cleaner Calibration
      - 14 Filament Sensor Calibration
      - 15 Phase Stepping Calibration
      - 16 Input Shaper Calibration
Settings
- - Tools
    - - Tool #
        
        Nozzle Diameter
        
        Nozzle Hardened
        
        Nozzle High-flow
        
        Pick/Park Tool
        
        Nozzle Offset
        
        Dock Position
      - Park Current Tool
  - Filament Sensors
    - - Filament Sensing
      - Filament Sensor 1
      - Filament Sensor 2
      - Filament Sensor 3
      - Filament Sensor 4
      - Filament Sensor 5
      - Filament Sensor 6
      - Filament Sensor 7
      - Filament Sensor 8
      - Restore Defaults
  - Auto-retract
  - Camera
  - Stealth Mode
  - Fan check
  - Verify Gcode
  - Nozzle Cleaner
  - Chamber Filtration
  - Input Shaper
    - - Calibration
      - X-axis filter
      - X-axis frequency
      - Y-axis filter
      - Y-axis frequency
      - Restore Defaults
  - Phase Stepping
  - User Interface
    - - Footer
        
        Item 1 [None/Nozzle/Bed/Filament/FSensor/Speed/X/Y/Z/Z Height/Print fan/Heatbreak fan/Heatbreak/Current tool/All nozzles/FSensor side/Nozzle diameter/Nozzle PMW/Enclosure temperature]
        
        Item 2
        
        Item 3
        
        Item 4
        
        Item 5
      - Sort Files [Time/Name]
      - Print Progress Screen [OFF, 30 s - 200 s]
      - Menu Timeout
      - Sound Mode [Loud/Silent/Assist/Once]
      - For filament change, preheat [Nozzle/Noz&Bed]
      - RGB Status Bar
      - RGB Side Strip
      - RGB Side Strip Dimming
      - Tool Light
      - Touch
      - Touch Sig Workaround
  - Language & Time
    - - Language
        
        English
        
        Čeština
        
        Deutsch
        
        Español
        
        Français
        
        Italiano
        
        Polski
        
        ニホンゴ
      - Time Zone Hour Offset
      - Time Zone Minute Offset
      - Time Zone Summertime
      - Time Format
  - Network
    - - Active Interface [Eth/Wi-fi]
      - Network status
        
        IPv4 Address
        
        IPv4 Gateway
        
        MAC Address
        
        Hostname
        
        DNS Server
        
        Ping | Loss
        
        Gateway
        
        DNS server
      - Wi-Fi
        
        Wi-Fi status
        
        SSID
        
        Wi-Fi Wizard
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Ethernet
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Prusa Connect
        
        Enabled
        
        Status
        
        Error
        
        Hostname
        
        Add printer to Connect
        
        Load Settings
      - Prusa Link
        
        Enabled
        
        User
        
        Password
        
        IPv4 address
        
        Hostname
        
        Generate Password
      - Metrics & Log
        
        What is this?
        
        Allow
        
        Enable Stored on Startup
        
        Stored configuration
        
        Host
        
        Metrics port
        
        Log Port
        
        Current configuration
        
        Metrics Host
        
        Metrics Port
        
        Log Host
        
        Log Port
  - Hardware
    - - Tools
      - Filament Autoloading
      - Door Sensor
      - Chamber Vent Control
      - Nozzle Cleaning Retraction
      - G-code checks
        
        Nozzle Diameter [Warn/Strict/None]
        
        Printer Model [Warn/Strict/None]
        
        Firmware Version [Warn/Strict/None]
        
        G-code Level [Warn/Strict/None]
      - Display Refresh Speed [High/Low]
  - FW update
  - Manual Belt Tuning
  - System
    - - Save Crash Dump
      - Save Logs To File
      - Device Hash in QR
      - Load Settings from File
      - Factory Reset
        
        Reset Settings & Calibrations
        
        Hard Reset (USB with FW needed)
Info
- - Network Status
    - - Wi-Fi Status
      - IPv4 Address
      - IPv4 Gateway
      - MAC Address
      - Hostname
      - DNS Server
      - Connect Host
      - Connect IP
      - Ping | Loss
        
        Connect
        
        Gateway
        
        DNS Server
  - Sensor Info
    - - Board Temperature
      - MCU Temperature
      - Bed Temperature
      - Chamber Temperature
      - Nozzle Temperature
      - Head PCB Tempeature
      - Head MCU Tempearture
      - Head Ambient Temperature
      - Nozzle Raw Temperature
      - Nozzle Power
      - Ringdown Decay
      - Loadcell Value
      - Door Sensor
      - Side Filament Sensor
      - Bed Voltage
      - Input Current
      - Fan Info
        
        Print Fan
        
        Heatbreak Fan
        
        Chamber Fan 1
        
        Chamber Fan 2
        
        Filtration Fan
  - Version info
    - - Firmware Version
      - Bootloader Version
      - Buddy Board
      - Serial Number
      - xLCD
  - Print Statistics
    - - Fail Stats
        
        Power Failures
        
        Last Print Crashes on X Axis
        
        Last Print Crashes on Y Axis
        
        Crashes on X Axis
        
        Crashes on Y Axis
      - Statistics
        
        X-axis
        
        Y-axis
        
        Z -axis
        
        Filament
        
        Tool #
        
        Tools changed
        
        Tool #
      - Print Time

この記事は役に立ちましたか？

この操作は登録ユーザーのみが利用できます。ログインしてください。

ログインしてコメントを投稿する

コメントなし

おすすめ製品

人気のカテゴリー

急上昇ワード

記事

ブログ

製品

カテゴリー

検索候補

LCD menu

(CORE One INDX)

Menu structure

LCD menu

(CORE One INDX)

Menu structure

トピックス