1. 組み立てを始める

プリンターメンテナンス

• How to rebuild the Nextruder Hotend
• How to replace the CoreXY plastic parts
• How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
• How to replace the Prusa Nozzle (XL single-tool)
• How to replace the Hotend assembly (XL single-tool)
• Prusaノズル（XLマルチツール）の交換方法
• How to replace a Z-axis motor (XL)
• Packing the Prusa XL printer for return - Original Packing material
• How to replace a heatbed tile and a heatbed tile cable (XL)
• How to replace a print fan (XL single tool)
• How to fix Modular bed error (HW solution)
• How to replace trapezoid nuts (XL)
• How to clean the side filament sensor (XL)
• How to change xLCD and xLCD cable (XL single-tool)
• How to replace a Dwarf board (XL multi-tool)
• How to replace Nextruder heatsink (XL Multi-tool)
• How to replace a Dwarf board (XL single-tool)
• How to replace the Hotend assembly (XL multi-tool)
• How to replace a hotend thermistor (XL Single-Tool)
• How to replace a Z-axis linear rail (XL)
• How to replace a profile insert (XL)
• How to replace the hotend fan (XL Multi-tool)
• How to replace a PSU (XL)
• How to replace a hotend heater (XL Single-Tool)
• How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
• How to replace the tch-profile-insert (XL)
• How to replace the Sandwich Board (XL)
• How to replace the rubber band on Original Prusa XL (Multi-tool)
• How replace the CoreXY Cover Rear (Original Prusa XL)
• ネクストルーダーV6ノズルアダプターの取り付け方法 (XLマルチツール)
  1. 組み立てを始める
  2. Introduction
  3. Handling Hot Components Safely
  4. Tools necessary for this chapter
  5. Select the tool
  6. Filament unloading
  7. Cleaning the hotend
  8. Park the tool
  9. Preparing the printer
  10. Undocking the Nextruder
  11. Disconnecting the hotend
  12. Removing the hotend
  13. Prusaノズルの取り外し
  14. V6ノズルの取り付け：部品の準備
  15. Nextruder V6ノズルアダプターの取り付け
  16. Installing the hotend
  17. Turning the printer ON
  18. Heating the nozzle
  19. Tightening the nozzle
  20. Adjusting the hotend
  21. ネクストルーダーをドックする方法
  22. Setting the nozzle diameter
  23. Tool Offset Calibration
  24. Tool Offset Calibration - Sheet install
  25. Tool Offset Calibration - pin installation
  26. Tool Offset Calibration - Done
  27. Calibration pin
  28. It's done
• How to replace a XY motor (XL)
• Packing the XL Enclosure for return - Original Packing material
• How to change the belt (XL)
• How to replace the main cable connector cover (XL)
• How to replace the PDU splitter (XL)
• How to replace the heatbed (XL)
• How to replace the print fan (XL multi-tool)
• How to replace trapezoid nuts (XL)
• How to lubricate linear bearing rails (XL)
• How to change the xLCD (XL)
• How to set up a Buddy3D Cam
• How to replace Nextruder heatsink (XL Single-tool)
• How to replace a Nextruder (XL single-tool)