1. Tools necessary for this chapter

Prusa INDX Conversion kit for the Prusa CORE One/+ [進行中の翻訳] (1.00)

• 1. Introduction
• 2. Printer preparation & disassembly
• 3. Z-axis upgrade
• 4. INDX Toolhead & Side filament sensors
• 5. Spoolholders & Tool dock assembly [進行中の翻訳]
  1. Tools necessary for this chapter
  2. Removing the side cover - right
  3. Side handle: parts preparation
  4. Installing the side handle
  5. Nozzle cleaner: parts preparation I.
  6. Nozzle cleaner: parts preparation II.
  7. Assembling the Wiper-lock
  8. Securing the Wiper-lock
  9. Installing the Wiper-adjuster
  10. Inserting the wiper blocks
  11. Mounting the wiper assembly
  12. Dock fan cable: parts preparation
  13. Attaching the dock fan cable
  14. Leading the dock fan cable I.
  15. Leading the Dock fan cable
  16. Securing the zip ties
  17. Securing the zip ties II.
  18. Electronics covers: parts preparation
  19. Securing the cables
  20. Wiring check
  21. xBuddyボードボックスのカバー
  22. 背面カバーの取り付け
  23. Mounting the side panel: Parts preparation
  24. Mounting the right side panel
  25. Bottom puck holders: parts preparation
  26. Assembling the bottom puck holders
  27. Removing the screws - left
  28. Mounting the bottom puck holders - left
  29. Securing the front puck holder bottom - left I.
  30. Securing the front puck-holder bottom - left II.
  31. Securing the rear puck holder bottom - left I.
  32. Securing the rear puck holder bottom - left II.
  33. Top puck holders: parts preparation
  34. Assembling the puck holder top
  35. Removing the top nylon rivets - left
  36. Mounting the front puck holder top - left
  37. Securing the front puck holder top - left
  38. Mounting the rear puck holder top - left
  39. Securing the rear puck holder top - left
  40. Removing the screws - right
  41. Mounting the bottom puck holders - right
  42. Securing the front Puck-holder bottom - right I.
  43. Securing the front Puck-holder bottom - right II.
  44. Securing the rear Puck-holder bottom - right I.
  45. Securing the rear Puck-holder bottom - right II.
  46. Tilting the printer
  47. Finishing the rear puck holder bottom - left I.
  48. Finishing the rear puck holder bottom - left II.
  49. Finishing the front puck holder bottom - left I.
  50. Finishing the front puck holder bottom - left II.
  51. Finishing the rear puck holder bottom - right I.
  52. Finishing the rear puck holder bottom - right II.
  53. Finishing the front puck holder bottom - right I.
  54. Finishing the front puck holder bottom - right II.
  55. Mounting the front puck holder top - right
  56. Securing the front puck holder top - right
  57. Mounting the rear puck holder top - right
  58. Securing the rear puck holder top - right
  59. Dock fan: parts preparation
  60. Assembling the dock fan
  61. Attaching the Dock fan splitter board
  62. Attaching the dock fan
  63. Securing the dock fan
  64. Haribo time!
  65. Tooldock: parts preparation
  66. Assembling the tool holder
  67. Installing the tool holders
  68. Nozzle seal holder: parts preparation
  69. Assembling the nozzle seal
  70. Assembling the Nozzle-seal-holder
  71. Installing the nozzle parking plates
  72. Ventilation lever: parts preparation
  73. Assembling the ventilation lever
  74. Top cover: parts preparation I.
  75. Top cover: parts preparation II.
  76. Attaching the hinge covers
  77. Attaching the grill
  78. Attaching the left cover lock
  79. Attaching the right cover lock
  80. Top cover back: parts preparation
  81. Attaching the top cover back
  82. Attaching the hinge base - left
  83. Attaching the hinge base - right
  84. Attaching the top cover I.
  85. Attaching the top cover II.
  86. INDX Nozzle tool: parts preparation
  87. Attaching the tooldock
  88. Securing the tooldock
  89. LEDパネルの取り付け
  90. Optional: Installing the Buddy3D Camera
  91. Connecting the INDX Nozzle tools (positions 1–4)
  92. Docking the tools (positions 1–4)
  93. Connecting the INDX Nozzle tools (positions 5–8)
  94. Docking the tools (positions 5–8)
  95. Checking the tubes
  96. Offset sensor cover: parts preparation
  97. Covering the offset sensor
  98. ドアパネル：部品の準備
  99. Mounting the door panel
  100. Attaching the stickers: Parts preparation
  101. Attaching the upgrade sticker
  102. Attaching the SN sticker
  103. Haribo time !
  104. That's it
• 6. Preflight check