JA
  • English
  • Čeština
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

4. Nextruder upgrade (Multi-Tool)

4. Nextruder upgrade (Multi-Tool)

4. Nextruder upgrade (Multi-Tool)
Relevant for:
Last updated 19 days ago
4. Nextruder upgrade (Multi-Tool)
 Difficulty
Moderate
 Steps
24
 Available languages
ENCSPLDEITFR
Nextruder cable bundle releasing
Nextruder cable bundle releasing
Nextruder cable bundle releasing
Nextruder cable bundle releasing
If you have an Original Prusa XL or an Original Prusa XL Upgrade dispatched on or after June 1, 2024, you do not need to upgrade the Multi-Tool Nextruder. You can go to this Section.
On the first Nextruder:
From the front side of the Nextruder, using a T10 screwdriver, loosen (a few turns are enough) two M3x8r screws and take off the cable support.
Locate the FESTO fitting, push the blue collet down and remove the PTFE tube from the Nextruder. Leave the PTFE hanging freely.
Starting from September 2024, you may receive a new black Fitting M5-4. The assembly and functionality remain identical to the blue one.
Locate the Nextruder cable, press the secure pin and unplug the cable from the first Nextruder. Leave the cable hanging.
Idler-swivel releasing
Idler-swivel releasing
Idler-swivel releasing
Idler-swivel releasing
Release an M3 screw with a 2.5 mm Allen key. A few turns are enough.
Open the cover by swiveling the cover 90 degrees.
Release the two M3x30 screws and remove the idler-swivel from the Nextruder. Leave the screws in the heatsink.
Place the idler-swivel nearby, we'll disassemble it later.
PG case releasing: four screws
PG case releasing: four screws
PG case releasing: four screws
PG case releasing: four screws
If your Nextruder has four screw cover, proceed to the next line. If your Nextruder has three screw cover, please proceed to the next step.
Remove the M3x25 screw using the 2.5mm Allen key. Don't throw the screw away!
Remove the idler from the Nextruder and place it nearby.
PG case releasing: three screws
PG case releasing: three screws
PG case releasing: three screws
PG case releasing: three screws
Unscrew and remove two M3x25 screws. Do not throw them away! Loosen the last screw, do not remove it!
Loosen the last screw, do not remove it!
Open the cover by turning it slightly to the side.
Idler releasing
Idler releasing
Idler releasing
Using a 1.5mm Allen key, remove the grub screw. Do not throw it away!
Remove the idler from the Nextruder.
Good job, now we have the idler and idler-swivel. Let's upgrade them!
Idler disassembly
Idler disassembly
Idler disassembly
Release and remove the M3x6 screw from the idler using a 2.5mm Allen key. Do not throw it away!
Remove the tubular spacer from the idler. Do not throw it away!
Remove the bearing from the idler, it's not connected with the pin. Do not throw them away!
Remove the pins from the idler. Do not throw them away!
Throw the old Idler-levers to the bin.
Nextruder idler: parts preparation
Nextruder idler: parts preparation
Nextruder idler: parts preparation
For the next steps, please prepare: 
Idler-lever-a (1x)
Idler-lever-b (1x)
Bearing 693 2RS (2x) you removed in the previous steps
M3x6 screw (1x) you removed in the previous steps
Pin 2.9x8.5 (2x) you removed in the previous steps
Tubular spacer 13.2x3.8x0.35 (1x) you removed in the previous steps
エクストルーダーアイドラーの組み立て
エクストルーダーアイドラーの組み立て
エクストルーダーアイドラーの組み立て
エクストルーダーアイドラーの組み立て
The next assembly steps for the idler and idler swivel are copy and paste. Continue with these steps, the assembly is the same - just with the PCCF parts.
Insert the pins 2.9x8.5 into each hole in the Idler-lever-a as seen in the picture.
Attach both bearings onto the pins into the Idler-lever-a.
Close it up with the Idler-lever-b part and secure it with the M3x6 screw. Do not overtighten the screw. Both bearings must be able to rotate without significant resistance.
同じ側からチューブラー・スペーサーをアッセンブリーに押し込みます。チューブラー・スペーサーの "底部 "は、アイドラー・アッセンブリーの底部と面一でなければなりません。
Idler-swivel disassembly
Idler-swivel disassembly
Idler-swivel disassembly
Release and remove the M3nN nut. Do not throw it away!
Remove the M3x20rT screw. Do not throw it away!
Remove the idler-nut. Throw it into the bin!
Idler-swivel disassembly
Idler-swivel disassembly
Idler-swivel disassembly
Release and remove the M3nN nut. Do not throw it away!
Remove the idler-swivel from the screw. Throw it into the bin!
Remove the M3x20rT and spacer from the second idler-swivel. Do not throw them away!
Throw the second idler-swivel into the bin.
Idler-swivel: parts preparation
Idler-swivel: parts preparation
Idler-swivel: parts preparation
For the following steps, please prepare:
Idler-swivel (2x)
Idler-nut (1x)
M3x20rT screw (2x) you removed in the previous steps
M3nN nut (2x) you removed in the previous steps
Spacer 6x3.1x8 (1x) you removed in the previous steps
Assembling the Idler-swivel
Assembling the Idler-swivel
Assembling the Idler-swivel
M3x20rTネジをIdler-swivelの片方に通してください。
スペーサーをネジにスライドさせます。
反対側から2つ目のIdler-swivelをネジの上に置きます。
反対側から、M3nNナットをネジに取り付けます。ユニバーサルレンチを使ってナットを持ち、ネジを締めます。軽く締めるだけで大丈夫です。スペーサーは自由に回転する必要があります。
Assembling the Idler-nut
Assembling the Idler-nut
Assembling the Idler-nut
Assembling the Idler-nut
Insert the idler-nut into the idler-swivel assembly. Make sure that both parts are oriented correctly according to the picture.
M3x20rT ネジを、最初のネジと同じように同じ側から挿入して、両方のパーツを固定します。
M3nN ナットで締結します。ナットを締めすぎないようにしてください。Idler-swivelがIdler-nutの上で動くようにしなければなりません。
Idler attaching: four screws
Idler attaching: four screws
Idler attaching: four screws
Idler attaching: four screws
If your Nextruder has four screw cover, proceed to the next line. If your Nextruder has three screw cover, please proceed to the next step.
Insert the assembled idler to its place.
Secure the idler with the M3x25 screw using a 2.5mm Allen key. Do not overtighten the screw! The screw protrudes from the PG-ring after tightening. 
Idler attaching: three screws
Idler attaching: three screws
Idler attaching: three screws
Idler attaching: three screws
Insert the assembled idler to its place.
Secure the idler with the M3 grub screw using a 1.5mm Allen key. Do not overtighten the screw! The screw protrudes from the PG-ring after tightening. 
Turn the PG-cover back.
Insert two M3x25 and secure all three screws using a 2.5mm Allen key.
Idler-swivel attaching
Idler-swivel attaching
Idler-swivel attaching
Idler-swivel attaching
Fit the assembled idler-swivel with two M3x30 screws.
Tighten both M3x30 screws. Stop tightening as soon as the screw tips reach the front face of the idler nut.
Close the cover.
Tighten a M3 screw using a 2.5 mm Allen key.
Fan shroud removing
Fan shroud removing
The next steps apply only, if your Nextruder has a PETG fan-shroud. If not, please proceed to the Nextruder docking
Remove two M3x13rT screws using a T10 Torx screwdriver. Don't throw the screws away!
Remove the PETG fan-shroud. Throw it into the bin (trash can).
Fan shroud securing
Fan shroud securing
Fan shroud securing
Attach the new PCCF fan-shroud onto the Nextruder.
Insert and secure two M3x14rT screws using a T10 Torx screwdriver.
Good job, the Nextruder is upgraded. We can attach it to the printer.
Nextruder docking
Nextruder docking
Nextruder docking
Take the Nextruder and place it carefully next to the dock.
Carefully dock the Nextruder.
Nextruder connecting
Nextruder connecting
Nextruder connecting
Nextruder connecting
Check that the cable bundle is not twisted!
Attach the cable connector into the top of the Nextruder.
Insert the semi-transparent PTFE tube into the fitting on the Nextruder. Push it all the way in.
Starting from September 2024, you may receive a new black Fitting M5-4. The assembly and functionality remain identical to the blue one.
Hook up the keyhole openings in the flexible plate of the cable bundle onto the screw heads and push it up to correct the position and tighten the marked two screws.
Good job
Good job
Well done. The first Nextruder is finished. All of your Nextruders have to be upgraded to the PCCF parts! After the upgrade, proceed to the next chapter.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us