JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

4. Electronics assembly

4. Electronics assembly
Relevant for:
Last updated 4 months ago
4. Electronics assembly
 Difficulty
Moderate
 Steps
5
 Available languages
ENCSPLESDEITFR
ケーブルの束をまとめる
ケーブルの束をまとめる
Before we proceed further, we need to twist the textile sleeve. This will prevent the cables inside to slip out during the print.
指をうまく使って、スリーブをやさしくひねり、数周のループができるようにします。(中のケーブルはひねりません。)
スリーブをひねることで、スリーブ自体の長さが効果的に縮まります。次のステップにおいて、スリーブを逆に少しだけひねり戻し、長さを確保する必要があるかもしれません。
エクストルーダーのケーブル束を接続する
エクストルーダーのケーブル束を接続する
エクストルーダーのケーブル束を接続する
エクストルーダーのケーブル束を接続する
ナイロンフィラメントを穴に差し込みます。
フィラメントがモーターの配線を押し込んでいないことを確認してください。この状態は、フィラメントが長すぎることを示しています。この場合には、スリーブをねじって、フィラメントを押し戻す必要があります。
スリーブをホルダーの中にずらします。このとき、ホルダーの中にスリーブが最低でも ホルダーの高さの 3/4 だけ入っていることを確認してください。
もう一度フィラメントがモーターケーブルを押していないことを確認し、必要に応じてスリーブを少しずつ巻き戻してフィラメントを押し上げます。
Extruder-cable-clip と 2本 の M3x10 ネジ を使って、ケーブルの束を固定します。
エクストルーダーのケーブル束を接続する
エクストルーダーのケーブル束を接続する
エクストルーダーのケーブル束を接続する
エクストルーダーのケーブル束を接続する
Connect the cables from the extruder to the RAMBo board:
P.I.N.D.A. probe (v-cable, 4 wires)
Left hotend fan (v-cable, 3 wires)
Extruder motor (yellow label with "E")
Extruder heater
Extruder thermistor (yellow/green heat shrink, orientation does not matter)
Front print fan (red heat shrink, ensure that the red wire is closer to the extruder thermistor connector)
Filament sensor cable (use the correct row of pins in the connector and ensure the red and blue wires are facing the outside of the board) In the third picture, the RAMBo board is facing with the USB port towards you.
Finalizing the Einsy-case
Finalizing the Einsy-case
Finalizing the Einsy-case
このステップのために、準備するもの:
M3x40 screw (1x)
Close the Einsy-door.
ケーブルが潰されないように注意してください!
M3x40 ネジ を締めこみます。
Hooray!
Hooray!
Congratulations, you've just upgraded the Original Prusa i3 MK2.5S 3D printer!
You're almost there... Just finish the chapter 6. Preflight check
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us