⬢MINI Bottom panel (1x)

⬢Feet bracket (4個)

⬢Foam block or foam pad set (2x)

⬢M3x12 screw (8x)

⬢M3n nut (8x)

⬢Gently push 8 pads out of the blocks.

Keep the remaining four pads as a spare.

⬢Peel the protective film from all pads. Be careful, there is glue (adhesive) applied on the pad.

⬢Glue the anti-vibration pad into each same-shape pocket in the foot-brackets. Always apply pressure to the pad to ensure proper adhesion.

⬢We recommend using a soft, clean pad when working with sheet metal parts to protect both the part and your workbench.

⬢Take the foot-bracket and align it with the two holes in the MINI Bottom panel as shown.

⬢Slightly lift the MINI Bottom panel.

⬢Slide the foot-bracket under the MINI Bottom panel until the holes in the base align with the holes in the foot-bracket.

⬢Again, check the holes in both parts are lined up.

⬢Insert two M3x12 screw into the holes.

⬢Fully tighten both screws.

⬢Proceed the same with all foot-brackets.

⬢Push the damper-insert into the anti-slip damper. No matter which side, the anti-slip damper is symmetrical.

⬢Turn the assembly on its feet and orient the MINI Bottom panel with the rectangular cutout facing to the front.

⬢Locate three threaded holes on the left side of the bottom panel. We will use them in the next step.

⬢Place the anti-slip damper on the threaded hole.

⬢Insert the M3x20 screw into the anti-slip damper and tighten it.

⬢Proceed the same for other anti-slip dampers.

⬢MINI Profile (4個)

⬢M4x5r ネジ (8本)

⬢Attach the MINI Profile to one of the MINI Bottom panel corner.

⬢Make sure the profile fits perfectly into the base.

⬢Join both parts together with two M4x5r screws. Tighten gently but firmly.

⬢Use the same procedure for all profiles.

⬢MINI Top panel (1x)

⬢MINI Top window panel (1x)

⬢ナイロンリベット (6個)

⬢M4x5r screw (8x)

NOTE: The following instructions are only for those who have purchased this optional add-on with the MINI Enclosure. If you have not purchased this add-on, please proceed to step Installing the top panel.

⬢Fire suppression system tube (1x) type: T033E BlazeCut T Series Fire Suppression 1 System with a pressure gauge

⬢Fire suppression brackets (2x)

⬢Thumb nut M3 (2x)

⬢M3x12 screw (2x)

⬢Attach the fire suppression bracket to one end of the tube. Pay attention to the direction.

⬢Attach the fire suppression bracket to the second end of the tube. Make sure it is in the same direction as the first one.

⬢Locate two holes in the MINI Top panel.

⬢Attach the prepared Fire suppression and align the bracket with the holes in the MINI Top panel. Mind the orientation of the Fire suppression in the picture.

⬢From the outside of the MINI Top panel:

⬢Insert the M3x12 screw through the hole.

⬢From the inside:

⬢Secure the screw with the M3 thumb nut.

⬢On the other side:

⬢From the outside of the MINI Top panel:

⬢Insert the M3x12 screw through the hole.

⬢From the inside:

⬢Secure the screw with the M3 thumb nut.

⬢Well done! The Fire suppression add-on is installed.

⬢Carefully place the MINI Top panel on the profiles, ensuring it is supported by all profiles.

⬢Check each support to ensure that the MINI Top panel is properly bearing down on it.

⬢Secure each profile with the MINI Top panel using two M4x5r screws.

In this step, you will learn how to secure the panels with the nylon rivets. Remember this method, as you will use it throughout the assembly.

⬢From the inside, carefully place the MINI Top window panel over the rectangular opening in the MINI Top panel.

⬢Align the holes of both parts.

⬢Insert the nylon rivet through the holes of both parts.

⬢Push on the nylon rivet to secure the window panel in the frame. When pressing on the nylon rivet, apply light pressure on the opposite side, specifically on the MINI Top window panel around the rivet.

⬢Repeat this procedure for the remaining holes in the opening.

⬢MINI Back panel (1x) with the octagonal cutout

⬢ナイロンリベット (8個)

⬢Turn the Enclosure sideways so that the rear side (without the PRUSA logo) is facing you.

⬢Peel off the protective layers from both sides of the MINI Back panel.

⬢From the inside, carefully place the MINI Back panel to the rear Enclosure "frame".

⬢Align the holes of the panel and the Enclosure "frame" and secure it with one nylon rivet near the top right corner. When pressing on the nylon rivet, apply light pressure on the opposite side, specifically on the MINI Back panel around the rivet.

⬢In this way, secure the panel around the entire perimeter.

NOTE: The following instructions are only for those who have purchased this optional add-on with the MINI Enclosure. If you have not purchased this add-on, please proceed to step Side panels: parts preparation

⬢Damper (3個)

⬢Thumb nut M3 (3x)

⬢M3x8 ネジ (3本)

⬢M4x16b countersunk screw (2x)

⬢Blower o-ring (1x)

⬢Filtration pack (1x)

⬢Push out the filter from the filtration pack and divide the pack into these individual parts:

⬢High Pressure Blower (1x)

⬢HEPA フィルター (1個)

⬢Filter-Bracket (1個)

⬢Place the Filter-Bracket like in the picture and push the Allen key through the hole as you can see.

⬢Attach the M3x8 screw on the tip of the Allen key.

⬢Using the Allen key, push the screw all the way through the front hole of the bracket. The screw must protrude partially.

⬢Tighten the damper on the screw.

⬢Repeat the same procedure to install the second damper.

⬢Using the Allen key, push the M3x8 screw through the protrusion on the other side of the Filter-Bracket.

⬢Tighten the damper on the screw.

⬢Place the Blower o-ring into the Filter-Bracket.

⬢Insert the High Pressure Blower into the Filter-Bracket so that the blower of the fan faces the hexagonal holes in the printed part.

⬢Join both parts together with two M4x16b countersunk screws.

⬢Orient the filtration assembly according to the picture. Make sure that two brackets are facing you and the cable is pointing to the left.

⬢From the left, push the HEPA filter all the way into the Filter-Bracket. Mind the orientation of the filter.

⬢From the inside, attach the filtration to the rear side of the Enclosure "frame" so that all three screws go through the holes.

⬢Secure all three damper screws by tightening three thumb nuts.

⬢Leave the filtration fan cable free for now. We will plug it later on.

⬢MINI Side panel (2x)

⬢ナイロンリベット (24個)

⬢Peel off the protective layers from both sides of the MINI Side panel.

⬢From the inside, carefully place the MINI Side panel to the left side of the Enclosure.

⬢Align the holes of the panel and the Enclosure and secure it with one nylon rivet near the top right corner.

⬢In this way, secure the panel around the entire perimeter.

Some of the following steps are marked as optional. If you do not need to install the handles at this time, skip to White LED strip (add-on): parts preparation

⬢Transport-handle (2x) this part is not included in the package, you will need to print it out from Printables.com

⬢M3nナット (6個)

⬢M3x12 ネジ (6本)

⬢Insert two M3n nuts into each Transport-handle.

⬢Insert the M3n nut from the other side into each Transport-handle.

⬢Using side cutters, CAREFULLY cut off all supports of each handle cutout on both side panels and remove it.

⬢Make sure that no nylon rivets are inserted in the two holes above the handle hole.

⬢From the inside, place the Transport-handle into the same shape cutout.

⬢Secure it with three M3x12 screws.

⬢Repeat the same procedure for the second Transport-handle.

NOTE: The following instructions are only for those who have purchased this optional add-on with the MINI Enclosure. If you have not purchased this add-on, please proceed to step Door hinges: parts preparation

NOTE: If you have installed the Advanced filtration system without the White LED Strip, proceed to step Guiding the filtration cables: parts preparation (add-on)

⬢LED Stick Board (1x)
WARNING: Make sure to protect the electronics against electrostatic discharge (ESD). Always unpack the electronics right before you need them!

⬢LEDディフューザー (1個)

⬢LED Stick Bracket (3x)

⬢M3x18 screw (3x)

⬢M3n nut (3x)

⬢Insert the M3n nut into each LED Stick Bracket.

⬢Slide the lower slot of the LED Stick Bracket on the LED Stick Board and align the bracket against the first hole in the LED Stick Board closest to the (white) LED stick connector.

⬢Push the LED Stick Bracket all the way on the LED Stick Board.

⬢Use this procedure for all three LED Stick Brackets.

⬢Remove the protection films from both sides of the LED diffuser.

⬢Push the LED diffuser into the LED Stick Brackets. Use the upper slot.

⬢From the outside, insert three M3x18 screws into the holes in the front left support profile.

⬢From the inside of the enclosure, attach the LED strip assembly so that the LED stick brackets are aligned precisely with the screws. Attach the back side (the side without the diffuser).

⬢Once the LED strip is aligned, attach it by tightening all three inserted M3x18 screws. Tighten them firmly but gently.

⬢LEDケーブル (1本)

⬢結束バンド (1本)

⬢Connect the LED cable to the connector on the bottom of the LED strip.

⬢Guide the zip tie through the perforation in the front left profile and secure the LED cable using the zip tie.

If you have only the White LED Strip add-on, skip this step.

⬢Guide the zip tie thought the perforation in the top panel near the filtration.

⬢Using this zip tie, secure the filtration cable. Do not overtighten the zip tie, as it may cause fatal damage to the cable.

⬢In the same way, secure the cable to the four perforations in the left rear profile. Do not overtighten the zip ties, as it may cause fatal damage to the cable.

⬢Leave the rest of the cable free for now.

The following steps of guiding the add-ons cables apply to both the White LED Strip and Advanced Filtration System add-ons.

From October 2024 you may receive two different manufacturers of the PSU, the pictures may be different but the assembly process is the same.

⬢製電源ユニット(1個)

⬢Zip tie (6x)

⬢Insert the PSU cable with the ferrite core through the circular hole at the rear of the Enclosure.

⬢Guide the PSU cable with the connector through the front circle hole out of the Enclosure.

⬢Release and remove both M3x12 screws.

⬢Reposition the foot as shown. Push the PSU cable into the cable channel.

⬢Push the PSU cable into the cable channel.

⬢Close the foot back to its original position and align the holes.

⬢Secure the foot by inserting back the M3x12 screws and tighten them firmly.

⬢Guide the cable along the rear side of the Enclosure and secure it using three zip ties through the perforations. Do not overtighten the zip ties, you can damage the cable.

⬢Guide the PSU cable along with the FAN cable on the left side of the Enclosure and secure it with the three zip-ties. Do not overtighten the zip ties, you can damage the cables.

⬢If you have installed the Advanced Filtration System, guide the filtration cable together with the PSU cable. Secure it with one extra zip tie in the left corner. Do not overtighten the zip tie, you can damage the cables.

⬢Push the printer PSU cable through the circle hole in the rear of the Enclosure.

⬢Slightly loosen the left screw behind the circle hole.

⬢Release and remove the right screw.

⬢Reposition the foot as shown in the picture. The cable channel must be accessible.

⬢Push the PSU cable into the cable channel.

⬢Close the foot back to its original position and align the holes in the foot and Enclosure.

⬢After aligning the hole, secure the foot by inserting back the M3x12 screw.

⬢Fully tighten the left screw.

The following steps apply to both the White LED Strip and Advanced Filtration System add-ons.

⬢Basic Board Cover (1x)

⬢Basic board (1x)

⬢M3x12 screw (2x)

⬢M3w serrated lock washer (2x)

⬢M3nS nut (2x)

⬢Mount the M3nS nut on the M3x12 screw. Attach it in a few threads on the tip of the screw.

⬢Push the screw with the nut all the way into the same shape hole inside the Basic Board Cover.

⬢Remove the screw from the nut.

⬢Use the same procedure for both slots in the Basic Board Cover.

⬢Guide the LED cable through the hole in the bottom panel out of the Enclosure.

⬢Guide the filtration cable through the hole in the bottom panel out of the Enclosure.

⬢Connect the filtration cable to the Basic Board slot labeled FAN.

⬢Connect the LED cable to the Basic Board slot labeled LED.

⬢From the inside the Enclosure, insert two M3x12 screw through the front profile.

⬢Attach two M3w serrated lock washer on the screws.

⬢Place the Basic Board into the Basic Board Cover and align the holes on both parts.

⬢Take the Basic Board assembly and align the holes with the screws in the profile.

⬢Attach the Basic Board assembly to the screws and tighten the screws from the inside.

⬢It is recommended to make a loop with the excess cable and secure it with a zip tie. This way, the cable will not get in the way.

⬢Connect the external PSU cable to the basic board from the left side.

These steps are only for LED strip and Advanced filtration system owners only. The smaller PSU space is for those with additional PSU. Otherwise, skip to Door hinges: parts preparation

⬢PSU holder is not included in the package, you will need to print it out from Printables.com

⬢XP PSU: This PSU is larger than the Delta PSU. You will need the:

⬢Delta PSU: This PSU is smaller than the XP PSU. You will need the:

These steps are only for LED strip and Advanced filtration system owners only. The smaller PSU space is for those with additional Delta PSU. Otherwise, skip to Door hinges: parts preparation

⬢次のステップのために、次のものをご用意ください：。

⬢PSU-holder (1x) this part is not included in the package, you will need to print it out from Printables.com

⬢Add-on PSU-holder-A (1x) this part is not included in the package, you will need to print it out from Printables.com

⬢Add-on PSU-holder-B (1x) this part is not included in the package, you will need to print it out from Printables.com

⬢M3x8 screw (2x)

⬢M3n nut (2x)

⬢結束バンド (1本)

⬢Insert the M3n nut into the PSU-holder.

⬢Insert the M3n nut into the PSU-holder.

These steps are only for LED strip and Advanced filtration system owners only. The smaller PSU space is for those with additional Delta PSU.

⬢Attach the Add-on PSU-holder-A to the rails on the PSU-holder.

⬢Attach the Add-on PSU-holder-B to the rails on the PSU-holder.

⬢Remove the nylon rivet on the left bottom corner.

⬢From the inside of the enclosure, insert two M3x8 screws through the cut-outs.

⬢Attach the PSU-holder on the screws.

⬢Secure the screws from the inside.

⬢Insert the printer PSU into the PSU-holder.

⬢Insert the add-on PSU into the PSU-holder.

⬢Secure the cables together with a zip-tie.

⬢Door-hinge (2個)

⬢Enclosure hinge (2個)

⬢Pin 3x20 (4x)

⬢M3nS ナット (8個)

⬢M3x8 screw (4x)

⬢Place the enclosure hinge into the door hinge. See the correct orientation of both parts.

⬢Insert the pin from both side of the hinge.

⬢Push two pins all the way into the hinge against a hard surface (e.g. workshop table). The end of the pin must be aligned with the surface of the printed part.

⬢Insert four M3n nuts into the hinge assembly.

⬢Repeat the same for the second hinge.

In the following instructions, we will install the hinges on the left side. However, it is optional which side you install the hinges on. The procedure is identical and does not affect the later installation of the door.

⬢Turn the enclosure with the front side facing to you.

⬢Locate two holes on the top of the left support. From the inside, insert two M3x8 screws.

⬢Attach the hinge on the screws and tighten the screws. Mind the correct orientation of the hinge.

⬢Use the same procedure to mount the upper door-hinge.

⬢If you do not need to install the Lock at this time, skip to Door assembly: parts preparation

⬢MINI Door panel (1x)

⬢M3x8 screw (2x)

⬢MINI Enclosure Door Handle (1x)

⬢Magnet 20x6x2 (2x)

⬢Lock housing nut (1x)

⬢ロックハウジング (1個)

⬢Lock wrench (1x)

⬢Insert two magnets all the way into two pockets in the door handle.

⬢Turn the door handle.

⬢Insert the lock housing into the same shape opening in the door handle.

⬢From the opposite side:

⬢Insert the nut onto the lock housing.

⬢Secure the lock housing by tightening the lock housing nut. Use the lock wrench for easier tightening.

⬢Attach the door handle on the door panel and secure it with two M3x8 screws.

⬢ロック (1個)

⬢Mechanical Lock Lever (1x)

⬢E-clip washer (1x)

⬢Insert the Lock into the lock mount.

⬢Hold the Lock in the Lock mount with your hand and turn the door panel.

⬢Attach the Mechanical Lock Lever to the Lock.

⬢Place E-clip washer on the Mechanical Lock Lever against the lock.

⬢Attach the Lock wrench on the lock and the washer. Using Needle-nose pliers, push the E-clip washer on the lock to secure the lock mechanism.

⬢The Mechanical Lock is ready. Compare the picture with your Mechanical Lock.

⬢Take the door panel assembly and place it on the open hinges on the left side of the enclosure.

⬢Secure the door assembly by tightening two M3x8 screws to the top hinge.

⬢Repeat the same for the bottom hinge.

⬢よくできました!

⬢MINI Door panel (1x)

⬢M3x8 ネジ (6本)

⬢MINI Enclosure Door Handle (1x)

⬢Magnet 20x6x2 (2x)

⬢Take the door panel assembly and place it on the open hinges on the left side of the enclosure.

⬢Secure the door assembly by tightening two M3x8 screws to the top hinge.

⬢Repeat the same for the bottom hinge.

⬢Insert two magnets all the way into two pockets in the door handle.

⬢Attach the door handle on the door panel from the outside.

⬢Secure it with two M3x8 screws

⬢Close the door to ensure the handle is mounted correctly.