JA
  • English
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

1. Introduction

1. Introduction
Relevant for:
Last updated 2 months ago
1. Introduction
 Difficulty
Very easy
 Steps
13
 Available languages
ENPLDEITFR
Preparing the Enclosure kit
Preparing the Enclosure kit
Preparing the Enclosure kit
Welcome to the manual on how to assembly the Original Prusa XL Enclosure.
Please prepare the Original XL Enclosure received from Prusa Research.
For the assembly, prepare a clean workbench with a space of at least 1 m x 1 m (40 in x 40 in).
If children are involved in assembly, always supervise them to avoid injury.
Printer compatibility
Printer compatibility
Printer compatibility
Printer compatibility
The XL Enclosure assembly manual is specifically intended for these devices:
Original Prusa XL Single-Tool
Original Prusa XL Dual-Head
Original Prusa XL Five-Head
Tools necessary for this guide
Tools necessary for this guide
Tools necessary for this guide
Tools necessary for this guide
For this guide, please prepare:
T10 Torx key (screwdriver)
1.5mm 六角レンチ
2.5 mm Allen key
Needle-nose pliers
Universal wrench
A cardboard box for use as heatbed protection during the assembly. Hint: use the Nextruder box.
前面、左側、右側、背面
前面、左側、右側、背面
重要:XLプリンタは大きいので、すべての写真においてボディ全体を写すことができません。マニュアルの中では、作業する側を説明する用語が使われています
Front side - the location featuring the xLCD screen.
Left side - identifiable by the safety sticker positioned along its edge.
Right side - in contrast to the left side, lacks a safety sticker.
Rear side - the remaining section housing the PSU (Power Supply Unit).
Manipulating with the printer
Manipulating with the printer
Manipulating with the printer
Never manipulate the printer by using the spoolholders or the upper metal flanges. You can damage the LED lights hidden inside.
When assembling, handle the base using the extrusions.
Manipulating with the enclosure
Manipulating with the enclosure
Manipulating with the enclosure
During the assembly, peel off all protective films from the plastic panels.
After removing the protective film, the side panel is more susceptible to scratches. Please proceed with caution.
Metal frames can be sharp, so be careful and handle them with care.
Use labels for reference
Use labels for reference
Use labels for reference
Fasteners on the labels has a scale of 1:1 and can be used to identify parts :-)
The numbers in parentheses below the fastener picture indicate the number of extra pieces added to the SPARE package.
For the most common screws and nuts you can also use the enclosed letter, which contains Prusa Cheatsheet on the other side.
help.prusa3d.com/cheatsheet から Prusa Cheatsheet をダウンロードすることができます。プリントは 100 % で、行ってください。拡大、縮小はうまくプリントできないのでしないでください。
高解像度の画像を見る
高解像度の画像を見る
help.prusa3d.comの組み立てガイドをご覧頂くと、オリジナルの画像を高解像度で見ることができます。
画像にカーソルを合わせ、左上にある拡大鏡ボタン(「オリジナルを表示」)をクリックします。
Prepare your desk
Prepare your desk
机を片付けましょう!片付けることで、小さな部品を紛失する確率が減ります。

作業スペースを確保します。十分なスペースを確保しましょう。すっきりとした平らな作業台があれば、良好な結果が得られるでしょう。

光あれ!明るい環境にいることを確認してください。別途、手元を照らすライトや予備の懐中電灯があると便利でしょう。
ビニール袋や取り外した梱包材を入れるものを用意し、後で分別できるようにしておきましょう。また、重要な部品が取り残され、廃棄されていないかを確認してください。
Preparing the printer
Preparing the printer
Preparing the printer
Preparing the printer
Plug the printer into the wall outlet and turn it ON.
If you have loaded the filament, unload it from the hotend.
Multi-tool -> Unload all filaments. On the screen, navigate to Filament -> Unload Filament and select the tool-head.
Remove the filament from the PTFE tube. It is necessary to completely remove it from the printer.
WARNING: The hotend and heatbed are very HOT. Do not touch these parts!!!
Move the Z-axis down. On the screen, navigate to Control -> Move axis -> Move Z. Leave the Z-axis at least 10cm above the bottom panel.
Cool down the printer. On the screen, navigate to Preheat -> Cooldown.
Wait until the hot parts are cooled down to ambient temperature. It takes approximately 10 minutes.
Printer unpluging
Printer unpluging
Turn the power switch OFF (symbol "O").
From the rear side of the printer, unplug the PSU cable.
Protecting the heatbed
Protecting the heatbed
Before you proceed, it is recommended to protect the heatbed.
Make sure the heatbed is cooled down to ambient temperature. Place the empty cardboard box approximately to the front center part of the heatbed.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us