LCD menu

The Original Prusa MK3.5S is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

Menu structure during printing

• Tune
  • • Live Adjust Z
    • Change Filament
    • Cancel Object
      • • Cancel Current
    • Print Speed
    • Nozzle Temperature
    • Heatbed Temperature
    • Print Fan Speed
    • Flow Factor
    • Filament Sensor
    • Stealth Mode
    • Sound Mode [Loud/Silent/Assist/Once]
    • Input Shaper
      • • Calibration
        • X-axis filter
        • X-axis frequency
        • Y-axis filter
        • Y-axis frequency
        • Restore defaults
    • Fan Check
    • Verify Gcode
    • Cutter (Only Available when MMU is installed)
    • User Interface
      • • Footer
        • Sort Files [Time/Name]
        • Print Progress Screen [OFF, 30 s - 200 s]
        • Menu Timeout
        • Sound Mode [Loud/Silent/Assist/Once]
        • For filament change, preheat [Nozzle/Noz&Bed]
        • RGB Status Bar
        • Touch
        • Touch Sig workaround
    • Network
      • • Active Interface [Eth/Wi-fi]
        • Network status
          • • Wi-fi status
            • IPv4 Address
            • IPv4 Gateway
            • MAC Address
            • Hostname
            • DNS Server
            • Connect Host
            • Connect IP
            • Ping | Loss
              • Connect
              • Gateway
              • DNS server
        • Wi-Fi
          • • Wi-Fi status
            • SSID
            • Wi-Fi Wizard
            • Protocol
            • LAN
            • IPv4 Address
            • IPv4 Netmask
            • IPv4 Gateway
            • Hostname
            • MAC Address
        • Ethernet
          • • Protocol
            • LAN
            • IPv4 Address
            • IPv4 Netmask
            • IPv4 Gateway
            • Hostname
            • MAC Address
        • Prusa Connect
          • • Enabled
            • Status
            • Error
            • Hostname
            • Add printer to Connect
            • Load Settings
        • Prusa Link
          • • Enabled
            • User
            • Password
            • IPv4 address
            • Hostname
            • Generate Password
        • Metrics & Log
          • • What is this?
            • Allow
            • Enable Stored on Startup
            • Stored configuration
              • Host
              • Metrics port
              • Log Port
            • Current configuration
              • Metrics Host
              • Metrics Port
              • Log Host
              • Log Port
    • Time Zone Hour Offset
    • Time Zone Minute Offset
    • Time Zone Summertime
    • Info
    • Message History
• Pause
• Stop

Menu structure when idle

• Print
• Preheat
  • • PLA
    • PETG
    • ASA
    • PC
    • PVB
    • ABS
    • HIPS
    • PP
    • FLEX
    • PA
    • Custom
      • • Name
        • Nozzle temperature
        • Nozzle Preheat Temperature
        • Bed Temperature
        • Is Abrasive
        • Requires Filtration
        • Confirm
    • Cooldown
• Filament
  • • Load filament
    • Unload filament
    • Change filament
    • Purge filament
    • Manage Filaments
      • • Loaded filament
          • • Name
            • Visible
            • Nozzle Temperature
            • Nozzle Preheat Temperature
            • Bed Temperature
            • Is Abrasive
            • Requires Filtration
        • Edit Filaments
        • Reorder Filaments
        • Enable Filaments
    • Preload to MMU (Only Available when MMU is installed)
      • • Preload All
        • Preload Filament 1
        • Preload Filament 2
        • Preload Filament 3
        • Preload Filament 4
        • Preload Filament 5
    • Preload to MMU Advanced (Only Available when MMU is installed)
      • • Filament 1 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
        • Filament 2 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
        • Filament 3 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
        • Filament 4 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
        • Filament 5 [PLA/PETG/ASA/PC/PVB/ABS/HIPS/PP/PA/FLEX]
        • Carry Out the Changes
    • Load to Nozzle (Only Available when MMU is installed)
      • • Load Filament 1
        • Load Filament 2
        • Load Filament 3
        • Load Filament 4
        • Load Filament 5
    • Unload Filament (Only Available when MMU is installed)
      • • PLA
        • PETG
        • ASA
        • PC
        • PVB
        • ABS
        • HIPS
        • PP
        • FLEX
        • PA
    • Eject From MMU (Only Available when MMU is installed)
      • • Eject From MMU 1
        • Eject From MMU 2
        • Eject From MMU 3
        • Eject From MMU 4
        • Eject From MMU 5
    • Cut Filament (Only Available when MMU is installed)
      • • Cut Filament 1
        • Cut Filament 2
        • Cut Filament 3
        • Cut Filament 4
        • Cut Filament 5
        • Manage Filaments (Only Available when MMU is installed)
• Control
  • • Move axis
      • • Move X
        • Move Y
        • Move Z
        • Move E
        • Cooldown
    •  Temperature
      • • Heatbed temperature
        • Nozzle temperature
        • Print Fan speed
        • Cooldown
    • Auto home
    • Set ready
    • Sheet profile
    • Disable Motors
    • Loading Test (Only Available when MMU is installed)
      • • Test Filament 1
        • Test Filament 2
        • Test Filament 3
        • Test Filament 4
        • Test Filament 5
    • Live Adjust Z
    • Cold Pull
    • Mesh Bed leveling
    • Bed level correction
      • • Left Side
        • Right Side
        • Front Side
        • Rear Side
        • Reset
    • Calibrations & tests
      • • 1. Fan test
        • 2. XY axis test
        • 3. Z alignment calibration
        • 4. Z axis test
        • 5. Heater test
        • 6. First Layer Calibration
• Settings
  • • Filament Sensor
    • MMU unit
    • Cutter (Only Available when MMU is installed)
    • Stealth Mode
    • Fan check
    • Verify GCode
    • Input shaper
      • • Calibration
        • X-axis filter
        • X-axis frequency
        • Y-axis filter
        • Y-axis frequency
        • Restore defaults
    • User Interface
      • • Footer
          • • Item 1 [None/Nozzle/Bed/Filament/FSensor/Speed/X/Y/Z/Z Height/Print fan/Hotend fan/Sheets/Finda/Nozzle diameter/Nozzle PMW]
            • Item 2
            • Item 3
            • Item 4
            • Item 5
        • Sort Files [Time/Name]
        • Print Progress Screen [OFF, 30 s - 200 s]
        • Menu Timeout
        • Sound Mode [Loud/Silent/Assist/Once]
        • For filament change, preheat [Nozzle/Noz&Bed]
        • RGB Status Bar
        • Touch
        • Touch Sig workaround
    • Language and Time
      • • Language
          • • English
            • Čeština
            • Deutsch
            • Español
            • Français
            • Italiano
            • Polski
            • ニホンゴ
        • Time Zone Hour Offset
        • Time Zone Minute Offset
        • Time Zone Summertime
        • Time Format
    • Network
      • • Active Interface [Eth/Wi-fi]
        • Network status
          • • Wi-fi status
            • IPv4 Address
            • IPv4 Gateway
            • MAC Address
            • Hostname
            • DNS Server
            • Connect Host
            • Connect IP
            • Ping | Loss
              • Connect
              • Gateway
              • DNS server
        • Wi-Fi
          • • Wi-Fi status
            • SSID
            • Wi-Fi Wizard
            • Protocol
            • LAN
            • IPv4 Address
            • IPv4 Netmask
            • IPv4 Gateway
            • Hostname
            • MAC Address
        • Ethernet
          • • Protocol
            • LAN
            • IPv4 Address
            • IPv4 Netmask
            • IPv4 Gateway
            • Hostname
            • MAC Address
        • Prusa Connect
          • • Enabled
            • Status
            • Error
            • Hostname
            • Add printer to Connect
            • Load Settings
        • Prusa Link
          • • Enabled
            • User
            • Password
            • IPv4 address
            • Hostname
            • Generate Password
        • Metrics & Log
          • • What is this?
            • Allow
            • Enable Stored on Startup
            • Stored configuration
              • Host
              • Metrics port
              • Log Port
            • Current configuration
              • Metrics Host
              • Metrics Port
              • Log Host
              • Log Port
    • Hardware
      • • Printer Type [MK3.5/MK3.5S]
        • Printhead
          • • Nozzle Diameter
            • Nozzle Hardened
            • Nozzle High-flow
            • Nextruder Silicone Sock
            • Nextruder
            • Calibrate Filament sensor
        • Filament Autoloading
        • Steel Sheets
        • G-code checks
          • • Nozzle Diameter [Warn/Strict/None]
            • Printer Model [Warn/Strict/None]
            • Firmware Version [Warn/Strict/None]
            • G-code Level [Warn/Strict/None]
            • MK3 Compatibility [Warn/Strict/None]
            • Fan Compatibility [Warn/Strict/None]
        • Display Refresh Speed [High/Low]
    • FW update
    • System
      • • Save Crash Dump
        • Save Logs to File
        • Device Hash in QR
        • Load Settings from File
        • Factory Reset
          • • Reset Settings & Calibrations
            • Hard Reset (USB with FW needed)
• Info
  • • Network Status
      • • Wi-Fi Status
        • IPv4 Address
        • IPv4 Gateway
        • MAC Address
        • Hostname
        • DNS Server
        • Connect Host 
        • Connect IP
        • Ping | Loss
          • Connect
          • Gateway
          • DNS Server
    • Sensor Info
      • • Heatbreak Temp
        • Board Temperature
        • Bed Temperature
        • MCU temperature
        • Nozzle Temperature
        • P.I.N.D.A.
        • Filament Sensor
        • FINDA (Only Available when MMU is installed)
        • Print Fan
        • Hotend Fan
        • Heater Voltage
        • Input Voltage
        • Heater Current
        • Input Current
        • MMU current
    • Version Info
      • • Firmware Version
        • Bootloader version
        • MMU Version (Only Available when MMU is installed)
        • Buddy board
        • Serial Number
        • LoveBoard
        • xLCD
    • Print Statistics
      • • Fail Stats
          • • Power failures
            • Load Fails in Print (Only Available when MMU is installed)
            • Total Load Fails (Only Available when MMU is installed)
            • General Fails in Print (Only Available when MMU is installed)
            • Total general Fails (Only Available when MMU is installed)
        • Statistics
          • • X Axis
            • Y Axis
            • Z Axis
            • Filament
            • MMU filament loads
            • Print Time