The Prusa CORE One L is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

Make sure to always have the latest firmware.

Menu structure during printing

Tune
- - Filament change
  - Cancel Object
  - Print Speed
  - Nozzle Temperature
  - Heatbed Temperature
  - Chamber Temperature
  - Print Fan Speed
  - Chamber Fans [Auto/0-100%]
  - Chamber Fans Limit
  - Filtration Fan
  - Chamber Filtration
    - - Chamber Filtration
        
        None
        
        Adv. filtration
        
        DIY
      - Filter Usage
      - Change Filter
      - Print Filtration
      - Minimum Power
      - Post-Print Filtration
      - Post-Print Duration
      - Post-Print Power
      - Filter All Materials
  - Flow Factor
  - Filament Sensors
    - - Filament Sensing
      - Side Filament Sensor
      - Toolhead Filament Sensor
      - Restore Defaults
  - Stuck Filament Detection
  - Stealth Mode
  - Sound Mode
  - Input Shaper
    - - Calibration
      - X-axis filter
      - X-axis frequency
      - Y-axis filter
      - Y-axis frequency
      - Restore defaults
  - Fan Check
  - Verify Gcode
  - Door Sensor
  - User Interface
    - - Footer
      - Sort Files [Time/Name]
      - Print Progress Screen [OFF, 30 s - 200 s]
      - Menu Timeout
      - Sound Mode [Loud/Silent/Assist/Once]
      - For filament change, preheat [Nozzle/Noz&Bed]
      - Light Settings
        
        RGB Status Bar
        
        Chamber Lights
        
        Chamber Dimming
        
        RGB Side Strip Dimmed
      - Touch
      - Touch Sig workaround
  - Network
    - - Active Interface [Eth/Wi-fi]
      - Network status
        
        Wi-fi status
        
        IPv4 Address
        
        IPv4 Gateway
        
        MAC Address
        
        Hostname
        
        DNS Server
        
        Connect Host
        
        Connect IP
        
        Ping | Loss
        
        Connect
        
        Gateway
        
        DNS server
      - Wi-Fi
        
        Wi-Fi status
        
        SSID
        
        Wi-Fi Wizard
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Ethernet
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Prusa Connect
        
        Enabled
        
        Status
        
        Error
        
        Hostname
        
        Add printer to Connect
        
        Load Settings
      - Prusa Link
        
        Enabled
        
        User
        
        Password
        
        IPv4 address
        
        Hostname
        
        Generate Password
      - Metrics & Log
        
        What is this?
        
        Allow
        
        Enable Stored on Startup
        
        Stored configuration
        
        Host
        
        Metrics port
        
        Log Port
        
        Current configuration
        
        Metrics Host
        
        Metrics Port
        
        Log Host
        
        Log Port
  - Time Zone Hour Offset
  - Time Zone Minute Offset
  - Time Zone Summertime
  - Info
  - Message History
  - Info
    - - Network Status
        
        Wi-Fi Status
        
        IPv4 Address
        
        IPv4 Gateway
        
        MAC Address
        
        Hostname
        
        DNS Server
        
        Connect Host
        
        Connect IP
        
        Ping | Loss
        
        Connect
        
        Gateway
        
        DNS Server
      - Sensor Info
        
        Board Temperature
        
        MCU temperature
        
        Bed Temperature
        
        Chamber Temperature
        
        Nozzle Temp
        
        Heatbreak Temp
        
        Bed MCU Temp
        
        Loadcell Value
        
        Door Sensor
        
        Filament Sensor
        
        Side Filament Sensor
        
        Print Fan
        
        Heatbreak Fan
        
        Chamber Fan 1
        
        Chamber Fan 2
        
        Filtration Fan
        
        Heater Voltage
        
        Input Voltage
        
        Heater Current
        
        Input Current
        
        MMU current
      - Version Info
        
        Firmware Version
        
        Bootloader version
        
        Buddy Board
        
        Serial Number
        
        Love Board
        
        xLCD
      - Print Statistics
      - Fail Stats
        
        Power failures
      - Statistics
        
        X Axis
        
        Y Axis
        
        Z Axis
        
        Filament
        
        MMU filament loads
        
        Print Time
  - Message History
Pause
Stop

Menu structure when idle

Print
Preheat
- - PLA
  - PETG
  - ASA
  - PC
  - PVB
  - ABS
  - HIPS
  - PP
  - FLEX
  - PA
  - Custom
  - Show All
  - Cooldown
Filament
- - Load filament
  - Unload filament
  - Change filament
  - Purge filament
  - Manage filaments
    - - Loaded filament
      - Edit filaments
      - Reorder filaments
      - Enable filaments
Control
- - Move axis
    - - Move X
      - Move Y
      - Move Z
      - Move E
      - Cooldown
  - Temperature
    - - Nozzle temperature
      - Heatbed temperature
      - Chamber temperature
      - Print Fan speed
      - Chamber Fans
      - Filtration Fan
      - Cooldown
  - Auto home
  - Set ready
  - Disable Motors
  - Cold Pull
  - Calibrations & tests
    - - 1. Fan test
      - 2. Door sensor
      - 3. Y axis test
      - 4. X axis test
      - 5. Homing Calibration
      - 6. Z Alignment calibration
      - 7. Loadcell test
      - 8. Z axis test
      - 9. Heater test
      - 10. Gearbox Calibration
      - 11. Filament sensor calibration
      - 12. Phase Stepping Calibration
Settings
- - Filament Sensors
    - - Filament Sensing
      - Side Filament Sensor
      - Toolhead Filament Sensor
      - Restore Defaults
  - Stuck Filament Detection
  - Auto Retract
  - MMU unit
  - Camera
  - Stealth Mode
  - Fan check
  - Verify GCode
  - Chamber Filtration
    - - Chamber Filtration
        
        None
        
        Adv. Filtration
        
        DYI
      - Filter usage
      - Chane Filter
      - Print Filtration
      - Minimum Power
      - Post-print Filtration
      - Post-print Duration
      - Post-print Power
      - Filter All Materials
  - Input shaper
    - - Calibration
      - X-axis filter
      - X-axis frequency
      - Y-axis filter
      - Y-axis frequency
      - Restore defaults
  - Phase Stepping
    - - Calibration
      - Restore defaults
  - User Interface
    - - Footer
      - Sort Files [Time/Name]
      - Print Progress Screen [OFF, 30 s - 200 s]
      - Menu Timeout
      - Sound Mode [Loud/Silent/Assist/Once]
      - For filament change, preheat [Nozzle/Noz&Bed]
      - Light Settings
        
        RGB Status Bar
        
        Chamber Lights
        
        Chamber Dimmming
        
        RGB Side Strip Dimmed
      - Touch
      - Touch Sig workaround
  - Language and Time
    - - Language
        
        English
        
        Čeština
        
        Deutsch
        
        Español
        
        Français
        
        Italiano
        
        Polski
        
        ニホンゴ
        
        українська мова
      - Time Zone Hour Offset
      - Time Zone Minute Offset
      - Time Zone Summertime
      - Time Format
  - Network
    - - Active Interface [Eth/Wi-fi]
      - Network status
        
        Wi-fi status
        
        IPv4 Address
        
        IPv4 Gateway
        
        MAC Address
        
        Hostname
        
        DNS Server
        
        Connect Host
        
        Connect IP
        
        Ping | Loss
        
        Connect
        
        Gateway
        
        DNS server
      - Wi-Fi
        
        Wi-Fi status
        
        SSID
        
        Wi-Fi Wizard
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Ethernet
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        Hostname
        
        MAC Address
      - Prusa Connect
        
        Enabled
        
        Status
        
        Error
        
        Hostname
        
        Add printer to Connect
        
        Load Settings
      - Prusa Link
        
        Enabled
        
        User
        
        Password
        
        IPv4 address
        
        Hostname
        
        Generate Password
      - Metrics & Log
        
        What is this?
        
        Enable Metrics
        
        Host
        
        Metrics Port
        
        Syslog Port
        
        MAC Address
        
        Metrics List
  - Hardware
    - - Printhead
        
        Nozzle diameter
        
        Nozzle hardened
        
        Nozzle high-flow
        
        Nextruder Silicone Sock
        
        Nextruder [MMU/Stock]
        
        Calibrate Filament Sensors
      - Filament Autoloading
      - Door Sensor
      - Check Ventilation Grilles
      - G-code checks
        
        Nozzle [Warn/Strict/None]
        
        Printer Model [Warn/Strict/None]
        
        Firmware Version [Warn/Strict/None]
        
        G-code Compatibility [Warn/Strict/None]
        
        G-code Level [Warn/Strict/None]
        
        Input Shaper [Warn/Strict/None]
      - Homing Calibration
      - Display Refresh Speed
  - FW update
  - Pre nozzle claning retraction
  - Manual Belt Tuning
  - System
    - - Save Crash Dump
      - Save Logs To File
      - Device Hash in QR
      - Load Settings from File
      - Factory Reset
        
        Reset Settings & Calibrations
        
        Hard Reset (USB with FW needed)
Info
- - Network Status
    - - Wi-Fi Status
      - IPv4 Address
      - IPv4 Gateway
      - MAC Address
      - Hostname
      - DNS Server
      - Connect Host
      - Connect IP
      - Ping | Loss
        
        Connect
        
        Gateway
        
        DNS Server
  - Sensor Info
    - - Board Temperature
      - MCU temperature
      - Bed Temperature
      - Chamber Temperature
      - Nozzle Temp
      - Heatbreak Temp
      - Bed MCU Temp
      - Loadcell Value
      - Door Sensor
      - Filament Sensor
      - Side Filament Sensor
      - Print Fan
      - Heatbreak Fan
      - Chamber Fan 1
      - Chamber Fan 2
      - Filtration Fan
      - Heater Voltage
      - Input Voltage
      - Heater Current
      - Input Current
      - MMU current
  - Version Info
    - - Firmware Version
      - Bootloader version
      - Buddy Board
      - Serial Number
      - Love Board
      - xLCD
  - Print Statistics
    - - Fail Stats
        
        Power failures
      - Statistics
        
        X Axis
        
        Y Axis
        
        Z Axis
        
        Filament
        
        MMU filament loads
        
        Print Time

Prusa CORE One L

À propos de votre imprimante

Prusa CORE One L electronics

LCD menu (CORE One L)