Español
Login

hotend&show=all | Buscar

hotend&show=all | Buscar | Prusa Knowledge Base Español Login Prusa Research as Impresoras 3D Materiales Piezas y accesorios Software Modelos 3D Aplicaciones Comunidad Ayuda Academy…

hotend | Buscar

Methods for replacing the Nextruder Hotend… hotend&show=all | Buscar Error mintemp hotend #13208 (MK4) #21208 (MK3.9) Si dispones de un multímetro, es posible comprobar la…

Hotend thermal runaway #23204 (MK3.5)

If there is a positive temperature change it means that the hotend thermistor is working and detecting the temperature change. Most likely, the issue stems from the hotend heater.…

Hotend preheat error #23202 (MK3.5)

If there is a positive temperature change it means that the hotend thermistor is working and detecting the temperature change. Most likely, the issue stems from the hotend heater.…

Hotend temp not matching #23210 (MK3.5)

The whole cartridge should be inside the block, with no part of it sticking out. Make sure the thermistor and heater are properly plugged into the electronics board.

Hotend mintemp error #23208 (MK3.5)

If there is a positive temperature change it means that the hotend thermistor is working and detecting the temperature change. Most likely, the issue stems from the hotend heater.…

Changing or replacing the Nextruder Hotend

Efectos cinematográficos prácticos: Sara Villareal y Studio Gillis Newsletter Regístrate y obtén nuestro dosier mensual de información útil sobre nuevos firmwares, nuevas versiones…

Hotend Heater Overcurrent #17322

Before performing any of the procedures, ensure the printer is fully cooled down, switched off, and disconnected from the mains.

Hotend maxtemp error #23206 (MK3.5)

Make sure the thermistor and heater are properly plugged into the electronics board. You can verify this from the dedicated step in our assembly manual. Check if the fuses are…

Selftest failed (MK3.5/S)

Heatbed & Hotend test In this step of the selftest, the hotend and heatbed will be heated to their maximum capacity to check if all cables are correctly connected and will not…

Extruder Maxtemp error #17206 (XL)

The hotend thermistor is rated to be 100 kΩ at 25 °C. To be realistic, with a varying temperature between 20 °C and 30 °C, you can expect a wider range of readings (~80-125 kΩ).…

How to replace the hotend fan (XL Multi-tool)

How to replace a PSU (XL) Como reemplazar un calentador del fusor (XL Mono Cabezal) Cómo lubricar los pasadores de acoplamiento de la Original Prusa XL (MultiCabezal) How to replace…

Loadcell troubleshooting

Alternatively, the loadcell testing can be initiated in LCD Menu -> Control -> Calibration & Tests -> Loadcell Test.

How to replace a hotend assembly (CORE One)

Comenzar el montaje Step 1 of 20 (Chapter 6 of 9) Modo pantalla completa Contenidos Comentarios How to replace a hotend assembly (CORE One) Dificultad Moderada Idiomas disponibles…

How to replace a hotend heatsink (MK4 / MK3.9)

Comenzar el montaje Step 1 of 42 (Chapter 13 of 14) Modo pantalla completa Contenidos Comentarios How to replace a hotend heatsink (MK4 / MK3.9) Dificultad Difícil Idiomas disponibles…

Hotend atascado (XL)

Un primer signo de obstrucción de la boquilla es que el filamento no se extruye de forma uniforme, se enrosca y se pega a la boquilla. Clic del extrusor El hotend o la boquilla…