Buddy firmware-specific G-code commands
A: Set the input shaper weight adjust frequency delta. M: Set the input shaper weight adjust mass limit. W<1>: Write current input shaper settings to EEPROM. M600 - M600: Filament…
Buddy firmware-specific G-code commands
A: Set the input shaper weight adjust frequency delta. M: Set the input shaper weight adjust mass limit. W<1>: Write current input shaper settings to EEPROM. M600 - M600: Filament…
It is possible to solder external pull-up resistors to the JP pins. This changes the behavior described above. For more details on that, see the pull-up resistors paragraph below.
EasyPrint | Prusa Knowledge Base Čeština Login Prusa Research as 3D tiskárny Materiály Díly & příslušenství Software 3D modely Průmysl Komunita Podpora Akademie Blog O nás Podpora…
Menu structure during printing Tune Live Adjust Z Change Filament Cancel Object Cancel Current Print Speed Nozzle Temperature Heatbed Temperature Print Fan Speed Flow Factor Filament…
Under-extrusion (Nextruder printers)
Slightly loosen the three bolts on the gearbox cover, by one turn and a half. On the LCD Menu, navigate to Filament -> Unload Filament.
The printer is displaying the message: The model was sliced for a different printer variant [SL1/SL1S]. Your printer variant is [SL1S/SL1].
Over time, filament dust may accumulate in the teeth of the pulleys. The best practice is regularly to clean them with a mini-brush or a similar tool.
Loadcell test 7. Z axis test 8. Heater test 9. Gears Calibration 10.
LCD menu (XL Single Tool) | Prusa Knowledge Base Čeština Login Prusa Research as 3D tiskárny Materiály Díly & příslušenství Software 3D modely Průmysl Komunita Podpora Akademie…
Tools Mapping and Filament Mapping (XL, MMU3)
Assigning parts of an object to a tool To reassign one part or multiple parts of the object to a tool, navigate in the G-code filaments column to the tool you wish to reassign,…
The printer is displaying the message: The model was sliced for a different printer variant [SL1/SL1S]. Your printer variant is [SL1S/SL1].
Any nozzle that is compatible with the E3D V6 Hotend can be installed on it.
The printer is displaying the message: The model was sliced for a different printer variant [SL1/SL1S]. Your printer variant is [SL1S/SL1].
Crash recovery home fail #31812 (CORE One) #26812 (MK4S) #1…
Hold the parts with your free hand! Loosen the lower M3x25 screw, and remove the extruder block. Loosen the M3x20 screws holding the trapezoid nut. Hold the parts with your free…
Tekutá pryskyřice (resin) - Glosář
The printer is displaying the message: The model was sliced for a different printer variant [SL1/SL1S]. Your printer variant is [SL1S/SL1].
Idler cannot home #04125 (MMU)
You can do so by running a specific G-code command: M708 A0x19 X10. (where X10 denotes threshold value 10.) After that you can reset the MMU with: M709 command.
Tool offset out of bounds #17104 (XL)
On the multi-tool versions of the Original Prusa XL, the offset of the tools compared to the first is calibrated through the Tool Offset Calibration.
The printer is displaying the message: The model was sliced for a different printer variant [SL1/SL1S]. Your printer variant is [SL1S/SL1].
E-mail Chci získat jako dárek e-book Základy 3D tisku Kliknutím udělujete souhlas se zasíláním newsletteru. Odeslat Tato stránka je chráněna pomocí reCAPTCHA Enterprise a uplatňuje…
In case either of the sensors is not triggered: Make sure that the extruder filament sensor is correctly connected to the LoveBoard.
Poslední příkaz lze vynechat, výchozí hodnota je nula. digits(a, num_digits, num_decimals=0) Zaokrouhlení / doplnění nulami: stejné jako výše, pouze ponechané vyplněné nulami.…
Osa X | Prusa Knowledge Base Čeština Login Prusa Research as 3D tiskárny Materiály Díly & příslušenství Software 3D modely Aplikace Komunita Podpora Akademie Blog O nás Prusa Research…
The printer is displaying the message: The model was sliced for a different printer variant [SL1/SL1S]. Your printer variant is [SL1S/SL1].
Komunitní překlady (MK3/MK3S/MK3S+)
Komunitní překlady (MK3/MK3S/MK3S+) | Prusa Knowledge Base Čeština Login Prusa Research as 3D tiskárny Materiály Díly & příslušenství Software 3D modely Průmysl Komunita Podpora…
Fil. sensor troubleshooting #26114 (MK4S) #13114 (MK4) #271…
Error name: Filament sensor stuck help MMU Error code: #26114 (MK4S) #13114 (MK4) #27114 (MK3.9S) #21114 (MK3.9) #28114 (MK3.5S) #23114 (MK3.5) How to fix it?
The printer is displaying the message: The model was sliced for a different printer variant [SL1/SL1S]. Your printer variant is [SL1S/SL1].
Print preview wrong filament #31805 (CORE One) #26805 (MK4S…
The printer can memorize the type of filament loaded in the print head.
The printer is displaying the message: The model was sliced for a different printer variant [SL1/SL1S]. Your printer variant is [SL1S/SL1].
Open chamber ventilation #31837 (CORE One)
Pro přidání kometáře se prosím přihlaste Zatím žádné komentáře Obsah What happened?
Legacy G-code for Tx If you, for example, issue a T5 command to the printer, this error will be shown, because the tool range available for MMU3 is T0-T4 only. How to fix it?