⬢Levý rám (1x)

⬢Boční panel (1x)

⬢Nylonový nýt (16x)

⬢Peel off the protective film from both sides of the side panel.

⬢Insert the side panel into the left-frame.

⬢Align up the side panel holes with left frame holes.

In this step, we will demonstrate how to secure the panels using the nylon rivets. Please familiarize yourself with this procedure, as it will be repeated several times throughout the manual.

⬢Align the hole in the side frame and the hole in the side panel.

⬢Insert the rivet through both the side frame and the panel.

⬢Zadní panel k rámu připevněte zatlačením nylonových nýtů.

⬢Insert the nylon rivet from the outside through the left frame and side panel.

⬢Secure the side panel with remaining 15 nylon rivets.

⬢Pravý rám (1x)

⬢Boční panel (1x)

⬢Nylonový nýt (16x)

⬢Peel off the protective film from both sides of the side panel.

⬢Insert the side panel into the right frame.

⬢Align the side panel holes with right frame holes.

⬢Insert the nylon rivet from the outside through the right frame and side panel.

⬢Secure the side panel with remaining 15 nylon rivets.

⬢From the inside of the side frame, insert the M4x16r screw into the threaded hole and tighten fully.

⬢Slide the protective bumper onto the screw from the outside of the side frame.

⬢Insert the magnetic bumper onto the screw and tighten it.

⬢From the inside of the side frame, insert the M4x16r screw into the threaded hole and tighten fully.

⬢Slide the protective bumper onto the screw from the outside of the side frame.

⬢Insert the magnetic bumper onto the screw and tighten it.

⬢Zadní panel (1x)

⬢Šroub M4x5r (12x)

⬢Put the left frame next to the back panel.

⬢Fit the perforation of the left frame into the cut-out on the back panel, and slide both pieces together as illustrated in the image to secure them.

⬢Připevněte panely třemi šrouby M4x5r z druhé strany pomocí 2,5mm inbusového klíče.

⬢Carefully turn the assembly and secure the panels with three M4x5r screws from the back side of the panels using a 2.5mm Allen key.

⬢Gently turn the back panel back onto the larger side.

⬢Put the right frame next to the back panel.

⬢Fit the perforation of the right frame into the cut-out on the back panel, and slide both pieces together as illustrated in the image to secure them.

⬢Připevněte panely třemi šrouby M4x5r z druhé strany pomocí 2,5mm inbusového klíče.

⬢Carefully turn the assembly and secure the panels with three M4x5r screws from the back side of the panels using a 2.5mm Allen key.

⬢Frame support (podpěra rámu) (1x)

⬢Šroub M4x5r (6x)

⬢Insert the frame support from the bottom side of the side frames. Note the logo orientation!

⬢Secure the left side with three M4x5r screws using a 2.5mm Allen key.

⬢Secure the right side with three M4x5r screws using a 2.5mm Allen key.

⬢Horní panel (1x)

⬢Nylonový nýt (13x)

⬢Insert the top panel into the frame assembly.

⬢Place the top panel, so the bottom edge is on top of the frame support.

⬢Place the top panel, so the top edge is under the top frame of the back panel.

⬢Filter and fan holder (1x)

⬢Blower (1x)

⬢Šroub M4x12b (2x)

⬢Stahovací páska (1x)

⬢Place the fan holder with metal cutouts towards you.

⬢Place the blower onto the filter-and-fan-holder.

⬢Secure the blower with two M4x12b using a 2.5mm Allen key.

⬢The fan and filter holder has two metal perforations, which fit into the back-panel cut-outs.

⬢Fit the perforation on the fan and filter holder into the cut-out on the back panel, and slide it down as shown in the image to secure them.

⬢Insert the whole blower cable through the hole in the back panel.

⬢Take the zip-tie and insert it through the metal cut-out in the filter and fan holder.

⬢Secure the blower cable with the zip-tie. Do not overtighten the zip-tie! Cut the end of the zip-tie.

⬢Insert the HEPA filter between the fan holder and the back panel, ensuring that the darker side of the filter (the side without the company text) is facing towards you.

⬢Push the HEPA filter all the way in.

⬢Kryt filtrace (1x)

⬢Šroub M4x5r (4x)

⬢Stahovací páska (2x)

⬢Attach the filtration cover to the fan holder assembly. Note the logo orientation!

⬢Secure the cover with four M4x5r screws using a 2.5mm Allen key.

⬢Zevnitř:

⬢Locate metal perforations.

⬢Insert two zip-ties through the perforations and secure the cable. Do not overtighten the zip-ties! 

⬢Cut the ends of the zip-ties.

The end of the fan cable will be secured later with LED strip add-on cable.

From November 2024, you may receive a new LED Stick Board, which can be supplemented with an additional LED strip.

⬢LED difuzér (1x)

⬢LED Stick Board (1x)

⬢Držák desky LED (LED Stick bracket) (3x)

⬢Šroub M3x18 (3x)

⬢Matka M3n (3x)

⬢Insert the M3n nut into the nut hole in the led-stick-bracket.

⬢Prepare all three led-stick-brackets.

⬢Attach the brackets onto the LED stick board. Mind the orientation of the LED stick board and the LED-stick-bracket. Look at the picture.

⬢Remove the protective foil from the both sides of LED diffuser.

⬢Slide the LED diffuser into the upper place in the LED-stick-brackets.

⬢Attach the assembled LED panel on the inner side of the right frame as shown.

⬢Secure the LED panel from the outside of the right frame with three M3x18 screws using a 2.5mm Allen key.

⬢LED cable 1100 mm (1x)

⬢Stahovací páska (12x)

⬢Take the LED cable and connect one end to the LED stick board.

⬢Insert three zip-ties through the perforations and secure the cable. Do not overtighten the zip-ties. Cut the ends of the zip-ties.

⬢Insert five zip-ties through the perforations and secure the cable. Do not overtighten the zip-ties. Cut the ends of the zip-ties.

⬢Insert zip-tie through the perforations and secure the cable. Do not overtighten the zip-tie. Cut the end of the zip-tie.

⬢Secure the LED strip cable and the fan cable with three zip-ties. Do not overtighten the zip-tie. Cut the end of the zip-tie.

⬢Insert the ends of the cables through the cut-out in the metal.

⬢Přední panel (1x)

⬢Door frame support (1x)

⬢Door frame top (1x)

⬢Šroub M4x8r (5x)

⬢Attach the door frame support from the inside as described in the picture.

⬢Attach the door frame top from the outside.

⬢Secure the support and the top with a M4x8r screw using a 2.5mm Allen key.

⬢Zajistěte podpěru na vrchu s pomocí 2,5mm inbusového klíče a zbývajících šroubů M4x8r.

⬢Door frame right (1x)

⬢Door frame left (1x)

⬢Kryt matky M4n (10x)

⬢Matka M4n (10x)

⬢Šroub M4x8r (12x)

⬢Prepare one M4 nut cover.

⬢Prepare one M4n nut.

⬢Insert the M4n nut into the M4n nut cover.

⬢Repeat this process for all remaining M4n nuts and M4n nut covers.

⬢Attach the door frame right onto the front panel.

⬢Secure the panel with the M4x8r screw using a 2.5mm Allen key.

⬢Insert the M4x8r screw into the hole.

⬢From the inside of the front panel, insert the M4n nut onto the screw.

⬢Šroub zajistěte pomocí 2,5mm inbusového klíče.

⬢Attach the door frame left onto the front panel.

⬢Secure the panel with an M4x8r screw using a 2.5mm Allen key.

⬢Insert the M4x8r screw into the hole.

⬢From the inside of the front panel, insert the M4n nut onto the screw.

⬢Šroub zajistěte pomocí 2,5mm inbusového klíče.

⬢Door frame bottom (1x)

⬢Kryt matky M4n (4x)

⬢Matka M4n (4x)

⬢Šroub M4x8r (4x)

⬢Attach the door frame bottom onto the front panel.

⬢Insert four M4x8r screws into the frame and secure them with M4 nuts using a 2.5mm Allen key.

⬢Insert the M4x5r screws into the hole.

⬢From the bottom side of the front panel, insert the magnetic bumper onto the screw and tighten it.

Hint: Use a 2.5mm Allen key for tightening the M4 screw.

⬢Insert the M4x5r screws into the hole.

⬢From the bottom side of the front panel, insert the magnetic bumper onto the screw and tighten it.

Hint: Use a 2.5mm Allen key for tightening.

⬢Remove the protective film from the front door left seal 1.

⬢Align the flat end with the door frame's left edge and apply the front door left seal 1 to the panel. Look at the picture.

⬢Remove the protective film from the front door left seal 2.

⬢Align the flat end with the door frame left edge and Apply the front door left seal 2 to the panel. Look at the picture.

⬢Remove the protective film from the front door right seal 1.

⬢Align the flat end with the door frame's left edge and apply the front door right seal 1 to the panel. Look at the picture.

⬢Remove the protective film from the front door right seal 2.

⬢Align the flat end with the door frame left edge and apply the front door right seal 2 to the panel. Look at the picture.

The hinges are installed on the outside of the front panel.

⬢Attach the first hinge on the front panel.

⬢Zajistěte závěs dvěma šrouby M4x12b pomocí 2,5mm inbusového klíče.

⬢Připevněte druhý závěs na přední panel a zajistěte jej dvěma šrouby M4x12b pomocí 2,5mm inbusového klíče.

⬢Pull out the protective battery foil.

⬢Insert the temperature sensor CORRECTLY into the front panel.

⬢Place the assembled front panel to the enclosure assembly.

⬢Align the hinge screw holes with the support frame holes.

⬢Na pravé straně víka vložte a zajistěte dva šrouby M4x12b pomocí 2,5mm inbusového klíče.

⬢On the left side of the lid, insert and secure two M4x12b screws using a 2.5mm Allen key.