EN
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

LCD menu (MK4)

Relevant for:
Last updated a month ago
This article is also available in following languages: 
PLDEESITFR

The Original Prusa MK4 is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

Make sure to always have the latest firmware.
  • Print
  • Preheat
      • PLA
      • PETG
      • ASA
      • PC
      • PVB
      • ABS
      • HIPS
      • PP
      • FLEX
      • PA
      • Cooldown
  • Filament
      • Load filament
      • Unload filament
      • Change filament
      • Purge filament
  • Control
      • Move axis
          • Move X
          • Move Y
          • Move Z
          • Move E
          • Cooldown
      •  Temperature
          • Heatbed temperature
          • Nozzle temperature
          • Print Fan speed
          • Cooldown
      • Auto home
      • Disable Motors
      • Calibrate Z
      • Filament Sensor Calibration
      • Run full Selftest
      • Diagnostics
          • Mesh bed leveling
          • Test fans
          • Test XYZ axis
          • Test heaters
          • Test loadcell
          • Show Selftest Result
  • Settings
      • Filament Sensor
      • MMU enable
      • Fan check
      • User Interface
          • Footer
          • Sort Files [Time/Name]
          • Print Progress Screen [OFF, 30 s - 200 s]
          • Menu Timeout
          • Sound Mode [Loud/Silent/Assist/Once]
          • For filament change, preheat [Nozzle/Noz&Bed]
          • RGB Status Bar
      • Language and Time
          • Language
          • Time Zone Offset
          • Time Format
      • Network
          • Prusa Link
              • Enabled
              • Generate Password
              • User
              • Password
          • Prusa Connect
              • Enabled
              • Status
              • Add printer to Connect
              • Load Settings
          • Default [Eth/Wi-fi]
          • IPv4 Address
          • MAC address
          • Ethernet
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • MAC Address
          • Wi-Fi
              • Setup Wi-fi Module
              • Create Credentials
              • Load Credentials
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • MAC Address
      • Hardware
          • Nozzle Diameter [0.40 mm/0.60 mm/0.80 mm/0.25 mm]
          • G-code checks
              • Nozzle Diameter [Warn/Strict/None]
              • Printer Model [Warn/Strict/None]
              • Firmware Version [Warn/Strict/None]
              • G-code Level [Warn/Strict/None]
          • Filament Autoloading
      • System
          • Save Crash Dump
          • Device Hash in QR
          • Load Settings from File
          • Factory Reset
  • Info
      • Sensor Info
          • Heatbreak Temp
          • Board Temperature
          • Bed Temperature
          • Nozzle Temperature
          • Loadcell Value
          • Filament Sensor
          • Print Fan
          • Heatbreak Fan
          • Heater Voltage
          • Input Voltage
          • Heater Current
          • Input Current
          • MMU current
      • Version Info
          • Firmware Version
          • Bootloader version
          • Buddy board
          • Serial Number
          • Love Board
          • xLCD
      • Print Statistics
          • Fail Stats
              • Power failures
              • Last Print Crashes
              • Crashes on X Axis
              • Crashes on Y Axis
          • Statistics
              • X Axis
              • Y Axis
              • Z Axis
              • Filament
              • Print Time
Was this article helpful?

Comments

0
Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us