⬢For this chapter, please prepare:
⬢T10 Torx key (T10 Torx screwdriver)
⬢2.5 mm Allen key
EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- XL
- Assembly manuals
- Original Prusa XL Single-Tool to Dual-Head Upgrade
- 3. Nextruder disassembly
3. Nextruder disassembly
Menu
- Original Prusa XL Single-Tool to Dual-Head Upgrade
- 1. Introduction
- 2. Printer preparing
- 3. Nextruder disassembly
- 1. Tools necessary for this chapter
- 2. Wi-Fi antenna detaching
- 3. PTFE unpluging
- 4. Disconnecting the Nextruder cable
- 5. Detaching the dock
- 6. Detaching the Nextruder
- 7. Detaching the Nextruder
- 8. Still no sweets?
- 9. Good job!
- 4. Nextruder upgrade
- 5. ToolChanger assembly
- 6. Nextruder & accessories assembly
- 7. First run
- Manual changelog
3. Nextruder disassembly
Relevant for:
Last updated 2 months ago Difficulty
Moderate Steps
9 Available languages
This step is only for the printer, which has a Wi-Fi antenna on the back of the printer.
⬢Turn the printer, so the back side of the printer is facing you.
⬢Unscrew the Wi-Fi antenna from the antenna connector and place it nearby.
⬢Turn the printer so the left side of the printer is facing you.
⬢Gently push the black collet to release the PTFE tube.
⬢Pull out the PTFE tube.
⬢Turn the printer, so the back side of the printer is facing you.
There is an antenna cable behind the antenna-holder, do not pull the connector!
⬢Loosen two screws on the cover slightly. No need to remove them completely. Push the cover to the right and gently remove it from the screws.
⬢Push the safety latch and disconnect the Nextruder cable from the connector "DWARF1".
⬢Attach the antenna-holder to the screws and push the cover to the left. Tighten the screws.
⬢Using a 2.5mm Allen key, untighten the screw inside the (middle hole) dock.
⬢Keep the Nextruder cable bundle next to the printer.
⬢Turn the printer, so the front side is facing you.
⬢Snap off the x-carriage-cover back from the X-carriage. Do not throw it away, we'll use it later!
⬢Using a T10 Torx key, remove two M3x12bT screws.
⬢Hold the Nextruder during disassembly.
⬢Remove two M3x12bT screws using a T10 Torx key.
⬢Unplug the Nextruder and place it nearby, we will rebuilt it in the next steps.
⬢Carefully and quietly open the bag with the Haribo sweets. A high level of noise might attract nearby predators!
⬢Spread the entire contents of the bag on a clean plate and arrange them according to the picture. The color doesn't matter that much.
The total number in your package may vary slightly. However, the exact number is important. If any gummy bears are missing, please go to your nearest candy store immediately.
⬢Eat ten gummy bears.
Did you know that gummy bears were first created by a German candy maker named Hans Riegel in the 1920s.
⬢Well done, the printer is ready for the assembly. Let's go to the next chapter: 4. Nextruder upgrade
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.