Packing printer for transport - Original Packing Material (XL)

Relevant for:

Last updated 4 days ago

Difficulty

Moderate

Steps

Available languages

Step 1 Introduction

⬢This guide will outline how to prepare and pack down your Original Prusa XL for return or repair using the packing material we supply with assembled printers.

⬢Contact our Customer support to receive the shipping label.

Be sure to read each step carefully! Colors on the Hexagon bullet points correspond to markers in the photos.

The package with the printer is heavy! Always ask another person for help with handling.

Step 2 Tools necessary for this step

⬢For this guide, please prepare:

⬢2,5mm Allen key

⬢4mm Allen key

⬢TX10 Torx key

⬢Black packing tape

⬢Wrapping tape

⬢Fragile stickers (4x) Can be downloaded here.

⬢Accessories for return shipment (you received with the printer)

Step 3 Necessary fixations for this guide

⬢For this manual, please prepare the complete original packaging material in which the Original Prusa XL printer was sent to you.

⬢For this guide, please prepare:

⬢Top front cardboard fixation

⬢Top rear cardboard fixation

⬢Extruder box

The list continues in the next step...

Step 4 Necessary fixations for this guide

⬢For this guide, please prepare:

⬢Left and right bottom rear fixation

⬢Left and right bottom front fixations

⬢Left and right top rear fixations

⬢Left and right top front fixations

Step 5 Preparing the printer

⬢If you have loaded the filament, unload it from the hotend. On the screen, navigate to Filament -> Unload Filament.

⬢Remove the filament from the hotend. It is necessary to completely remove it from the printer.

⬢Move the Z-axis down. On the screen, navigate to Control -> Move axis -> Move Z.

⬢Cool down the printer. Go to Preheat -> COOLDOWN.

Wait until the hot parts are cooled down to ambient temperature. It takes approximately 10 minutes.

Step 6 Removing the Wi-Fi antenna

Make sure the printer is cooled down.

⬢Turn the printer OFF and unplug the power cord.

⬢Turn the printer with its back to you.

⬢Unscrew and remove the Wi-Fi antenna from the printer.

⬢Place the antenna into the bag with other accessories.

Step 7 Disconnecting the PTFE tube

⬢Push the black collet to release the PTFE tube.

⬢Gently pull out the PTFE tube.

Step 8 Disconnecting the extruder cable

⬢Slightly loosen two screws on the cover. No need to remove them completely. Push the cover to the right and remove it from the printer.

⬢Press the secure pin and release the extruder cable.

⬢Attach the connectors cover to the screws. Push it all the way to the left and tighten the screws.

Step 9 Removing the xl-dock-cable-router

⬢Push the 2,5mm Allen key all the way through the hole in the rear metal sheet until you reach the screw in the xl-dock-cable-router and release the screw. Leave the screw in the xl-dock-cable-router.

⬢Take off the xl-dock-cable-router.

⬢Leave the extruder cable bundle with the PTFE tube freely over the printer to the rear side.

Step 10 Removing the extruder

⬢Remove the X-carriage-cover from the X-carriage.

⬢Use the TX10 key to unscrew both lower M3x12b.

Step 11 Removing the extruder

Hold the extruder with your hand to pretend the fall of the extruder while unscrewing.

⬢Use the TX10 key to unscrew both upper M3x12b.

⬢Take off the extruder.

Step 12 Packing the extruder

⬢Pack the extruder carefully into the box with the fixture provided.

⬢First, close the bottom part of the box.

⬢Second, close the upper part of the box.

⬢Put the extruder packaging aside for now, we'll use it later.

Step 13 Fixing the metal insert

The M3x10 screw prevents the damage of the plastic parts during the transport.

⬢Take one M3x10 screw from the spare parts.

⬢Insert the M3x10 screw into the insert and secure it using a 2.5mm Allen key. The metal insert has not move!

Step 14 Disassembling the LCD

⬢Use 2,5mm Allen key to unscrew both M3x18 screws from the LCD supports.

⬢Gently unplug the LCD cable.

Step 15 Disassembling the LCD

⬢Use the TX10 key to release the screw securing the PE cable.

⬢Let the cables hang freely.

⬢Pack the LCD into the bubble wrap to prevent damage while shipping.

Step 16 Removing the spool holder

⬢Use a 4mm Allen key to release the M5x85 screw and take off the spoolholder.

⬢Leave the M5nEs in the frame.

⬢Pack the spoolholder a into the bag with other accessories.

⬢Put the printer aside for now, we'll use it later.

Step 17 Preparing the bottom

⬢The bottom part of the box has 4 pre-cut holes for shipping straps.

⬢Use your finger to create holes in the cardboard.

Step 18 Preparing the bottom

Do not twist the shipping straps.

⬢Take the shipping straps.

⬢Stretch the shipping strap between two holes as described in the picture.

⬢Move the shipping strap to be the same length on both sides.

⬢Stretch the shipping strap on the second side of the bottom part box.

Step 19 Preparing the bottom

⬢Insert the cardboard base into the bottom part of the box.

⬢The front of the box shows cardboard cuts on the sides.

⬢Put the fixation into the cardboard base as described in the picture.

Step 20 Inserting the printer

Do not hold the printer by the top metal profiles!!! Otherwise, you may warp the printer and damage the LED lighting inside the profiles.

プリンターは2人で扱うこと。

⬢Use the side handles on both sides of the printer to handle.

⬢Insert the printer into the cardboard base.

Be careful to orient the printer correctly to the front of the box base.

⬢Keep the steel sheet on the printer. No need to pack it separately.

Step 21 Installing the fixations

The extruder box will "lock" the printer in its place.

⬢Lay out the box cutouts so that the box can be pushed through them.

⬢Lock the cardboard pins into the extruder box.

Step 22 Preparing the top

⬢Use a knife to cut the tape and open the box.

⬢Put the top part on a prepared cardboard base.

Step 23 Preparing the top

⬢Locate the pre-cuts on the top part.

⬢Use your finger to create holes.

⬢The holes are for the shipping straps. We will use them later.

Step 24 Installing the top

Front and back white fixations are not the same.

⬢Put four white fixations on top of the printer.

⬢Prepare top cardboard fixations, we'll use them in the next steps.

Step 25 Installing the top fixation

⬢Put the larger cardboard fixation between the box and the white fixture.

⬢Turn the cardboard cutout around the X-carriage to fix it in position.

⬢Rotate the package.

⬢Use a tape to secure the cutout.

Step 26 Installing the top fixation

⬢Put the smaller cardboard fixation between the box and the white fixture.

⬢Rotate the package.

⬢Use the space in the fixation to store accessories that you received with the printer.

If you have a Prusament box, you can fill it with accessories and use the free space in a larger cardboard fixture.

Step 27 Preparing the shipping straps

The shipping strap must be flattened, not twisted.

⬢Push the strap through the prepared hole in the top part box.

⬢Do this step for all straps on both sides.

Step 28 Preparing the shipping straps

Check if are the shipping straps all the same length.

⬢Prepare the shipping strap clip.

⬢For securing shipping straps use this video.

Step 29 Wraping the package

⬢Use wrapping tape to tape all places as described in the pictures.

Make at least a minimum of 3 lines of wrapping tape on yellow spots.

⬢Cover the shipping straps with wrapping tape.

⬢Use packing tape or food wrap (transparent) for wrapping the whole package. You'll protect your package from unnecessary damage.

Step 30 Labelling the package

⬢Place the "Fragile" stickers at least on four sides of the box. Do not place them on the top or bottom side.

You get the shipping label from our Customer support.

⬢Place the shipping label on the side with the fragile sticker.

Step 31 Hooray! The printer is ready to ship

⬢Great job! Your printer is ready for shipping.

Packing printer for transport - Original Packing Material (XL)

Packing printer for transport - Original Packing Material (XL)

Step 1 Introduction

Step 2 Tools necessary for this step

Step 3 Necessary fixations for this guide

Step 4 Necessary fixations for this guide

Step 5 Preparing the printer

Step 6 Removing the Wi-Fi antenna

Step 7 Disconnecting the PTFE tube

Step 8 Disconnecting the extruder cable

Step 9 Removing the xl-dock-cable-router

Step 10 Removing the extruder

Step 11 Removing the extruder

Step 12 Packing the extruder

Step 13 Fixing the metal insert

Step 14 Disassembling the LCD

Step 15 Disassembling the LCD

Step 16 Removing the spool holder

Step 17 Preparing the bottom

Step 18 Preparing the bottom

Step 19 Preparing the bottom

Step 20 Inserting the printer

Step 21 Installing the fixations

Step 22 Preparing the top

Step 23 Preparing the top

Step 24 Installing the top

Step 25 Installing the top fixation

Step 26 Installing the top fixation

Step 27 Preparing the shipping straps

Step 28 Preparing the shipping straps

Step 29 Wraping the package

Step 30 Labelling the package

Step 31 Hooray! The printer is ready to ship

Comments

Still have questions?