⬢For this chapter, please prepare:
⬢T10 Torx key (T10 Torx screwdriver)
⬢2.5 mm Allen key
JA
Login- English
- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- XL
- 組立てガイド
- Original Prusa XL Single-head to Double-head [進行中の翻訳]
- 3. Nextruder disassembly
3. Nextruder disassembly
Menu
- Original Prusa XL Single-head to Double-head [進行中の翻訳]
- 1. Introduction
- 2. Printer preparing
- 3. Nextruder disassembly
- 1. Tools necessary for this chapter
- 2. Wi-Fi antenna detaching
- 3. PTFE unpluging
- 4. Disconnecting the Nextruder cable
- 5. Detaching the dock
- 6. Detaching the Nextruder
- 7. Detaching the Nextruder
- 8. Still no sweets?
- 9. Good job!
- 4. Nextruder upgrade
- 5. ToolChanger assembly
- 6. Nextruder & accessories assembly
- 7. First run
- Manual changelog
3. Nextruder disassembly
Relevant for:
Last updated 2 months ago Difficulty
Moderate Steps
9 Available languages
This step is only for the printer, which has a Wi-Fi antenna on the back of the printer.
⬢Turn the printer, so the back side of the printer is facing you.
⬢Unscrew the Wi-Fi antenna from the antenna connector and place it nearby.
⬢Turn the printer so the left side of the printer is facing you.
⬢Gently push the black collet to release the PTFE tube.
⬢Pull out the PTFE tube.
⬢Turn the printer, so the back side of the printer is facing you.
There is an antenna cable behind the antenna-holder, do not pull the connector!
⬢Loosen two screws on the cover slightly. No need to remove them completely. Push the cover to the right and gently remove it from the screws.
⬢Push the safety latch and disconnect the Nextruder cable from the connector "DWARF1".
⬢Attach the antenna-holder to the screws and push the cover to the left. Tighten the screws.
⬢Using a 2.5mm Allen key, untighten the screw inside the (middle hole) dock.
⬢Keep the Nextruder cable bundle next to the printer.
⬢Turn the printer, so the front side is facing you.
⬢Snap off the x-carriage-cover back from the X-carriage. Do not throw it away, we'll use it later!
⬢Using a T10 Torx key, remove two M3x12bT screws.
⬢Hold the Nextruder during disassembly.
⬢Remove two M3x12bT screws using a T10 Torx key.
⬢Unplug the Nextruder and place it nearby, we will rebuilt it in the next steps.
⬢Carefully and quietly open the bag with the Haribo sweets. A high level of noise might attract nearby predators!
⬢きれいな入れ物に袋の中身を全部広げ、写真のように並べます。色はそれほど重要ではありません。
ハリボーパッケージの中に入っているクマの数が少ないかもしれません。そんなときは、すぐに近くのお菓子屋さんに行って買い足しましょう。用法・用量は正確に行ってください。
⬢グミを10個食べましょう。
グミは1920年代にハンス・リーゲルというドイツのキャンディーメーカーによって初めて作られたことをご存知だろうか。
⬢Well done, the printer is ready for the assembly. Let's go to the next chapter: 4. Nextruder upgrade
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.