JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

Multi Material Post Processor Troubleshooting

Multi Material Post Processor Troubleshooting

Multi Material Post Processor Troubleshooting
Relevant for:
Last updated 9 months ago
Multi Material Post Processor Troubleshooting
 Difficulty
Moderate
 Steps
8
 Available languages
ENCSPLESDEITFR
異なるスライサー
異なるスライサー
Only Slic3r G-code is now supported!! Load gcode generated by Slic3r.
This error pops up if you'll use unsupported slicing software.
Make sure that you used Slic3r to generate the G-code
すでに処理済みのファイル
すでに処理済みのファイル
Selected G-code is already processed! Nothing to do.
This error pops up if you loaded already processed g-code by the Multi Material post procesor
Post processor has nothing to do, everything is fine and the g-code you tried to load is already prepared. Just print it.
間違ったセッティング
間違ったセッティング
G-code has been generated with incorrect slic3r settings!! Make sure you used Prusa i3 MK2 Multi Material settings!
This error pops up if you loaded g-code generated with incorrect settings. For example with profile for "Prusa i3 MK2"
Regenerate g-code with "Prusa i3 MK2 Multi Material" profile and try it again.
サポートされていないレイヤーの高さ
サポートされていないレイヤーの高さ
G-code has unsupported layer height!! Only 0.15, 0.2 and 0.35 mm is supported!
This error pops up if you sliced the model with unsupported layer height
At this time, only 0.15, 0.2 and 0.35 mm layer heights are supported, make sure you have supported layer height set in your slicer profile and try again.
サポートされていない最初のレイヤーの高さ
サポートされていない最初のレイヤーの高さ
G-code has unsupported first layer height!! Only 0.15, 0.2 and 0.35 mm is supported!
This error pops up if you sliced the model with unsupported first layer height
At this time, only 0.15, 0.2 and 0.35 mm first layer heights are supported. Make sure you have supported first layer height set in your slicer profile and try again.
可変レイヤー高さ
可変レイヤー高さ
G-code has variable layer height!! Variable layer height is unsupported for now, please turn it off in Slic3r!
This error pops up if you sliced the model with variable layer height.
At this time, variable layer height is not supported, make sure you used right slicer profile and variable layer height is turned off.
Variable layer height can be turned off by unchecking the box in "Printer Settings" -> "General" -> "Enable variable layer height feature:"
実行中…
実行中…
実行中…
This informs you that work is in progress.
Post processing time depends on your hardware specs, g-code size and number of extruders.
If the post processing time exceeds 10 minutes and you don't have hardware from stone age, try restarting the post processor and repeat process.
ファイルの読込み中…
ファイルの読込み中…
ファイルの読込み中…
This status tells you that loading selected file is in progress.
Loading time depends on your hardware specs and g-code size.
If the post processing time exceeds 10 minutes and you don't have the g-code on super slow drive, try restarting the post processor and repeat process.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us