JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

2. Extruder disassembly

2. Extruder disassembly
Relevant for:
Last updated 2 years ago
2. Extruder disassembly
 Difficulty
Moderate
 Steps
14
 Available languages
ENCSPLESDEITFR
プリンタの準備
プリンタの準備
始める前に確認すること:
the filament is unloaded from the hotend
プリンターが適切に冷却されていること
プリンタのプラグが抜かれている
you removed the steel sheet
Releasing the cable bundle
Releasing the cable bundle
Releasing the cable bundle
Releasing the cable bundle
Using an Allen key release the M3x40 screw and open the door.
Release two M3x10 screws and remove the extruder-cable-clip. On older printers cut the zip tie.
In case there are zip ties inside the Einsy-case, carefully remove them.
Remove the zip ties on the cable holder.
Remove the textile sleeve (spiral wrap) all the way to the Einsy-case.
Unplugging the extruder cables
Unplugging the extruder cables
Unplugging the extruder cables
Open the Einsy-case and follow all the cables from the hotend. Unplug them one by one.
WARNING: some cables have a safety latch, don't pull them!
Leave the other cables connected.
Removing the filament sensor cable
Removing the filament sensor cable
Removing the filament sensor cable
Removing the filament sensor cable
Release all five screws and remove the X-carriage-back. Be careful with the wires. Disassemble the cable-holder and keep it for the rebuild.
Unplug the connector and remove the filament sensor cable. This is cable is no longer needed and will be replaced with a new one.
Carefully separate the cables and push them to sides.
Removing the extruder
Removing the extruder
Removing the extruder
Removing the extruder
Release both M3 screws.
Before removing the last screw, hold the extruder as it will fall down.
Carefully lay the extruder on the heatbed and push the cables through the X-axis.
Return to the X-carriage:
Remove the black nylon and keep it for later.
Remove the belt and keep it for later.
Cut the zip ties and remove the carriage completely. For the MK2.5S you will need a different one.
Fans and motor removal
Fans and motor removal
Fans and motor removal
Fans and motor removal
プリントファンを取り外す前に、ノズルファン(ファンシュラウド)が先に取り外されていることを確認します。
Release all screws on both fans and carefully remove them.
アイドラーを固定している両方のネジを外します。
Remove the fan support.
WARNING: release all three screws, but keep in mind the motor will fall off!
Hotend removal
Hotend removal
Hotend removal
Hotend removal
Release both M3 screws and remove the Extruder-cover so you can reach the hotend.
WARNING: Removing hotend from the extruder needs a "special" technique, then the hotend slides out quite easily. Don't use excessive force, or you will damage some parts irreversibly!!!
The hotend is removed by inclining and pulling at the same time. See the picture showing the WRONG inclination. This hotend is inclined too much to the front and there is no gap between the hotend and the extruder body. Hotend is partly inside and you won't be able to remove it.
The second picture is showing the CORRECT inclination. The hotend is tilted, but there is a gap between the hotend and the extruder body. You will be able to remove it.
PTFEチューブの取り外し
PTFEチューブの取り外し
このステップは必須です! MK2.5SはMK2.5に比べて短いPTFEチューブを使用していますので、今すぐ交換しましょう!
黒いプラスチックのコレットをホットエンドに向けて押し下げます。
ホットエンドから古いPTFEチューブを取り外します。
新しいPTFEチューブを挿入する
新しいPTFEチューブを挿入する
新しいPTFEチューブを挿入する
新しいPTFEチューブを挿入する
アップグレードパッケージを開封し、新しい(短い)PTFEチューブの入った袋を探します。
新しいPTFEチューブを確認します。両端がきれいであることを確認してください。
さて、いよいよ新しいPTFEチューブを挿入します。端が2つの異なる形状であることに注意してください。
チューブの一端は「ラウンド」のエッジになっています。 こちら側がホットエンドの内部に入る方です。
反対側の端をご覧ください、チューブの内側にドリルで内部の穴を処理しています。エッジ内部が「円錐形」になっています。こちら側が、フィラメントがチューブに入ってくる方で、ホットエンドの外側になります。
Push the black collet in. Slide the tube all the way in and hold it!
Using second hand pull the collet out and only then release the tube!!! THIS IS CRUCIAL for the hotend to work properly.
Removing the Bondtech gear
Removing the Bondtech gear
EXTRA WARNING!!! Be extremely cautious during this step!!! You can easily strip the lock screw and irreversibly damage it.
First, make sure the Bondtech isn't glued to the shaft. This is valid in case of the pre-assembled printer. If there is a glue, heat the shaft first (heatgun, lighter). Be careful, you can burn yourself.
Second, carefully release the lock screw. If the resistance is too high, use a grease (e.g. WD-40) and wait for a while.
Remove the Bondtech gear from the shaft and keep it for later.
Idler disassembly
Idler disassembly
Push and pull out the shaft. Keep it for later.
Take out the Bondtech gear, BUT BE CAREFUL, there are two bearings inside. Don't lose them!!!
Removing the filament sensor (optional)
Removing the filament sensor (optional)
Removing the filament sensor (optional)
This step is optional, you will use a different sensor in the new extruder.
Release two screws holding filament-sensor-cover.
Release the M3x10 screw holding the filament sensor.
Remove the sensor, avoid touching the PCB and the chips on it.
Disassembly is finished!
Disassembly is finished!
We are done here!
Before you move on, let's recap:
Throw away all the plastic parts, keep only the cable-holder.
Keep both fans, hotend (with replaced PTFE), F.I.N.D.A. sensor, Nylon filament and the X-axis belt.
Keep the motor and both Bondtech gears including bearings and the shaft.
Throw away the filament sensor with the cable, we will use a new one.
Fasteners are included in the upgrade kit, you can use these as a spare.
Ready? Let's jump to the 3. E-axis assembly
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us