I seriously doubt that anyone who has opted into a DIY upgrade needs another screw driver or a pair of needle-nose plyers. On the other hand, many of us English-speaking folks don't have a 3mm drill bit. Why not include that instead?
Be prepared for 30 hours of work and a lot to learn which makes the process more than bearable. Done the upgrade and everything works. Note that the y-rods holders from the old printer can be reused.
This ask may be a bit late, as Prusa is not selling the MK3S+ in kit form anymore, but... We are just now unboxing our MK3S+ kit. We purchased two, built one, and we kept busy with that for the past couple-few years. Now we are assembling the second MK3S+ (from kit). So, the ask... It would be nice if in the assembly manual there was reference or guidance not only for disassembly of a pre-built MK3S+, but also for an unassembled MK3S+. This request might also apply for any/all upgrade kits. Thanks!
They did, It's called the MK4 assembly guide :) It seems like a pretty incredibly rare use case. It just doesn't seem like it would really be in the best interest of time for them to do that. I'm not sure why the logic seems to be escaping you but if you have all the parts for the mk3s+ and all the parts for the MK 3.9 then all you need to do is follow the assembly guide for the MK4 and call it a day. It's a pretty simple solution. The only difference is the hot end and the x-axis, so when you get to those six pages you simply grab the parts from the upgrade kit instead of from the mk3s+Hope this helps the other one or two people on Earth that may have this scenario smiley face
Currently working on upgrading to 3.9. Its stalling because I'm waiting for new bearings I ordered. It would have been nice if at ordering the upgrade I could opt for replacement bearings there and then, and opt-out for the tools that were shipped with the upgrade. Shipping tools with the upgrade seems a bit silly to me (I have three sets now.....).
Yeah, you have to think about the logistics side of it. Including tools in every box simplifies the process and ensures efficiency because they don’t make kits to order. The warehouse is set up to have these kits ready to roll. If they had to decide whether to include tools for each order, it would slow down logistics and delay shipping. I suspect those tools cost only about three or four dollars. It's likely more cost-effective to give everyone tools than to pay for the extra labor and potential errors from forgetting tools when needed. If tools were accidentally left out, the company would then have to package and ship them separately, causing delays and incurring additional shipping and packaging costs. And honestly, who complains about getting extra stuff for free? You can donate the tools, give them to your kid to play with, or recycle them.
We are just now unboxing our MK3S+ kit. We purchased two, built one, and we kept busy with that for the past couple-few years.
Now we are assembling the second MK3S+ (from kit).
So, the ask...
It would be nice if in the assembly manual there was reference or guidance not only for disassembly of a pre-built MK3S+, but also for an unassembled MK3S+.
This request might also apply for any/all upgrade kits.
Thanks!
I'm not sure why the logic seems to be escaping you but if you have all the parts for the mk3s+ and all the parts for the MK 3.9 then all you need to do is follow the assembly guide for the MK4 and call it a day. It's a pretty simple solution. The only difference is the hot end and the x-axis, so when you get to those six pages you simply grab the parts from the upgrade kit instead of from the mk3s+Hope this helps the other one or two people on Earth that may have this scenario smiley face
Hi Halflink, thanks for the suggestion regarding bearings and tools, I will see what can be done :)
I suspect those tools cost only about three or four dollars. It's likely more cost-effective to give everyone tools than to pay for the extra labor and potential errors from forgetting tools when needed. If tools were accidentally left out, the company would then have to package and ship them separately, causing delays and incurring additional shipping and packaging costs.
And honestly, who complains about getting extra stuff for free? You can donate the tools, give them to your kid to play with, or recycle them.