⬢Push three magnets into the PSU-retainer. The polarity of the magnet is not important.
⬢Screw two M3x12 screws with two standoffs into the PSU-holder. Do not tighten the screw completely! There must be 2-3 mm space between the screw head and the standoff.
⬢Insert two M3nS nuts into the PSU-handle. Use the 2.5 mm Allen key to completely push the nuts inside.
⬢Guide the LCD cable through the cutout in the bottom panel.
⬢Secure the textile sleeve on the cable bundle with the zip tie. Do not over tighten the zip tie, it may cut the cables!
⬢From the inside, push two M3x8 screws through the bottom profile.
⬢Place the LCD assembly close to the LCD cables, like in the picture. Mind the same orientation of the LCD as in the picture. See the LCD-supports for better understanding.
Note that both cables are marked with stripes on one side. Correct connection order is important!
⬢Connect the LCD cable marked with TWO STRIPES to the left slot (called EXP2) on the LCD controller.
⬢Connect the LCD cable marked with ONE STRIPE to the right slot (called EXP1) on the LCD controller.
⬢Slide the LCD assembly onto the two M3x8 screws in the frame and tighten them.
⬢Attach the Filament-guide-b on the Filament-guide-a part and join them together by three M3x8 screws. Do not tighten the screws completely, a few turns are enough for now.
⬢Slide the PTFE tube all the way into the hole in the filament guide. From the opposite side, check if the PTFE tube is completely inserted to the end. If not, slide the PTFE a little more. See the direction of the PTFE tube.
⬢Insert two M3n nuts into the Thermometer-bracket.
⬢Insert the temperature sensor in the Thermometer-bracket. Push on it by your thumbs until you feel a slight "click". Avoid pressing on the screen, you can damage it.
⬢From the inside, mount the thermometer to the top left corner. Secure it with two M3x8 screws.
⬢There are protective foils on both sides of the panel. Peel off both foils.
⬢Place the edge of the door panel on the door trim. Both sides of the panel are symmetrical. It doesn't matter which side you put it on the door trim. It is important that the circular hole is placed on the door trim.
⬢Align the edges of the door panel with both ends of the door trim.
⬢Proceed the same with the second door panel.
In the next step, we will need door-magnet-a and door-magnet-b. These parts are not the same! Both parts are marked with the letter "A" and "B" and have a different shape.
Do not overtighten the screws in the door panel! The panel could crack.
⬢Take one of the door assemblies and place it on the open hinges on the right side of the enclosure. Make sure the handle is on the outside of the panel.
⬢Secure the door assembly by tightening two M3x8 screws in each hinge.
Look at the detail for a better illustration of how the door panel is attached to the hinge.
⬢Take the second door assembly and place it on the open hinges on the left side of the enclosure. Make sure the handle is on the outside of the panel.
⬢Secure the door assembly by tightening two M3x8 screws in each hinge.
⬢Completely insert two M3n nuts into the holes in the Spool-holder-r.
⬢From the inside, attach the Spool-holder-r to the corner on the right side of the enclosure. Secure it with two M3x12 screws. See the orientation of the Spool-holder-r.
⬢Insert the side arm into the Spool-holder-r and turn counter-clockwise to lock it.
If you have a question about something that isn't covered here, check out our additional resources. And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.