JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

PTFEチューブのトリミング方法 - マルチマテリアル

Menu

PTFEチューブのトリミング方法 - マルチマテリアル

PTFEチューブのトリミング方法 - マルチマテリアル
Last updated a year ago
PTFEチューブのトリミング方法 - マルチマテリアル
 Difficulty
Moderate
 Steps
11
 Available languages
ENCSPLESDEITFR

Step 1 導入と適切なツール

導入と適切なツール
導入と適切なツール
導入と適切なツール
導入と適切なツール
This guide is dedicated to the PTFE trimming for multi material Original Prusa printers, supported models are listed later on.
For single material Original Prusa printers PTFE trimming guide, go to: PTFEチューブのトリミング方法 - Original Prusa プリンター
ATTENTION!!! Please read all instructions at least twice! If you trim or drill the tube improperly, you will have to order it again!
READ CAREFULLY instructions for the tools before you proceed further. Prusa Research is not responsible for any harm or injury.
マルチマテリアルを組み立てる際、PTFEチューブが長すぎてY-スプリッターに入らないことがあります。
For trimming get a cutting tool with a thin blade. Use either razor or carpet knife. DON'T use kitchen knife.
For drilling is recommended to use a drill bit with conic head or you can use a drill bit with diameter 3,5 - 4 mm. The point is to make a conical entrance in the tube.

Step 2 Where to trim the tube (important)

Where to trim the tube (important)
Where to trim the tube (important)
IT IS CRUCIAL to cut the correct end of the tube, check twice before you start!
チューブの一端は「ラウンド」のエッジになっています。 この部分を切らないでください
反対側の端をご覧ください、チューブの内側にドリルで内部の穴を処理しています。エッジ内部が「円錐形」になっています。こちら側はカットできます。

Step 3 PTFEチューブのトリミング

PTFEチューブのトリミング
PTFEチューブのトリミング
PTFEチューブのトリミング
Take the razor or knife and carefully trim the tube.
Don't press too hard during the cutting on the tube, you can deform the circular shape and this will lead to filament jam!
Optimal length is 41 mm for Multi Material.

Step 4 Drilling the tube's edge

Drilling the tube's edge
Drilling the tube's edge
Drilling the tube's edge
After cutting the tube to appropriate length, you need to renew the conical entrance.
最初に用意したドリル刃を使用します。電動ドリルでも構いませんが、低回転に設定し、非常に優しく押してください。
It is important to achieve smooth entrance, so the filament will slide in. Clean the tube from any particles, which might prevent it.
これで完了です。PTFEチューブをMultiplexerに戻し、組み立てを続行します。

Step 7 PTFE for the MK3S/MK2.5S MMU2S (part 1)

PTFE for the MK3S/MK2.5S MMU2S (part 1)
PTFE for the MK3S/MK2.5S MMU2S (part 1)
PTFE for the MK3S/MK2.5S MMU2S (part 1)
PTFE for the MK3S/MK2.5S MMU2S (part 1)
マルチマテリアルプリンターで使用するPTFEチューブの理想的な形状をご紹介します。寸法・角度は推奨値です。
HOTEND PTFE
PTFE HOLDER
EXTRUDER TO MMU2S UNIT
MMU2Sプリンター用の他のPTFEチューブについては、次のステップを参照してください。
All dimensions are in millimetres.

Step 8 PTFE for the MK3S/MK2.5S MMU2S (part 2)

PTFE for the MK3S/MK2.5S MMU2S (part 2)
PTFE for the MK3S/MK2.5S MMU2S (part 2)
マルチマテリアルプリンターで使用するPTFEチューブの理想的な形状をご紹介します。寸法・角度は推奨値です。
MMU2S UNIT TO BUFFER
All dimensions are in millimetres.

Step 9 OBSOLETE: PTFE for the MK3/MK2.5 MMU2 (part 1)

OBSOLETE: PTFE for the MK3/MK2.5 MMU2 (part 1)
OBSOLETE: PTFE for the MK3/MK2.5 MMU2 (part 1)
OBSOLETE: PTFE for the MK3/MK2.5 MMU2 (part 1)
OBSOLETE: PTFE for the MK3/MK2.5 MMU2 (part 1)
マルチマテリアルプリンターで使用するPTFEチューブの理想的な形状をご紹介します。寸法・角度は推奨値です。
HOTEND PTFE
PTFE HOLDER
SPOOL HOLDER
MMU2プリンター用の最後のPTFEチューブについては、次のステップを参照してください。
All dimensions are in millimetres.

Step 10 OBSOLETE: PTFE for the MK3/MK2.5 MMU2 (part 2)

OBSOLETE: PTFE for the MK3/MK2.5 MMU2 (part 2)
OBSOLETE: PTFE for the MK3/MK2.5 MMU2 (part 2)
マルチマテリアルプリンターで使用するPTFEチューブの理想的な形状をご紹介します。寸法・角度は推奨値です。
EXTRUDER TO MMU2 UNIT
All dimensions are in millimetres.

Step 11 OBSOLETE: PTFE for the MK2/S MMU1

OBSOLETE: PTFE for the MK2/S MMU1
OBSOLETE: PTFE for the MK2/S MMU1
OBSOLETE: PTFE for the MK2/S MMU1
マルチマテリアルプリンターで使用するPTFEチューブの理想的な形状をご紹介します。寸法・角度は推奨値です。
HOTEND PTFE
EXTRUDER TO MULTIPLEXER
All dimensions are in millimetres.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us