How to replace the Prusa Nozzle (CORE One)

Relevant for:

CORE One

Last updated 17 days ago

Difficulty

Easy

Steps

Available languages

Step 1 Introduction

⬢This guide will take you through the Prusa Nozzle replacement on your Original Prusa CORE One.

The following instructions are compatible with all Prusa Nozzle diameters.

⬢All necessary parts are available in our eshop prusa3d.com.

Note that you have to be logged in to have access to the spare parts section.

Step 2 Tools necessary for this chapter

⬢Please prepare tools for this chapter:

⬢T10 Torx key

⬢Wrench 13-16

⬢Universal wrench

Step 3 Printer Preparation (Part 1)

⬢Close the printer’s door.

⬢Unload the filament. Visit the menu Filament and select Unload filament.

⬢プリンタからフィラメントを取り外します。

⬢Remove the filament spool from the printer.

Ensure the printer has completely cooled down.

⬢On the printer screen, navigate to Preheat -> COOLDOWN and wait for the temperatures to drop to ambient levels. This may take several minutes.

Step 4 Printer Preparation (Part 2)

⬢Open the menu Control > Move Axis > Move Z and set it to 100 mm or more.

⬢Wait until the heatbed moves down.

⬢Turn the printer off using the switch on the back.

⬢Disconnect the printer from power.

Step 5 Top Cover Removal

⬢Open the printer. From the inside, reach for the nylon rivet on the front right of the top cover. Push it out to unlock it.

⬢Then, remove the rivet from the outside.

⬢On the far right side of the cover, remove the other nylon rivet using the same technique.

⬢Remove the top cover.

Step 6 Heatbed Protection

Before proceeding any further, it is recommended to protect the heatbed first!

⬢Use a piece of fabric or other material thick enough to cover the heatbed. This will ensure you won't damage (scratch) the surface during the process.

Step 7 Nextruder Uncovering

⬢Let’s move onto the left side of the Nextruder.

⬢Using the T10 key, remove the two M3x12rT screws holding the side cover.

⬢Remove the cover.

Step 8 Cables Disconnecting

各コネクターには安全ラッチがあります。取り外す前に、ラッチを押す必要があります。さもないと、コネクターが破損する恐れがあります。

⬢Disconnect the hotend heater cable.

⬢Disconnect the hotend thermistor cable.

Step 9 Hotend Assembly Removal

⬢Remove the hotend cables from the cable guide.

⬢

Grasp the hotend with your hand.

⬢もう片方の手で2本のサムスクリューを緩めます。完全に外す必要はなく、数回回すだけで十分です。

Watch out, the hotend assembly may fall out!

⬢ホットエンドアセンブリをヒートシンクからスライドして外します。

Step 10 Prusa Nozzle Removal

⬢Remove the silicone sock from the heater block.

⬢Use the 13-16 wrench to hold the heater block securely.

⬢Use the 7mm cutout in the universal wrench to grasp and loosen the nozzle.

⬢Manually unscrew and remove the Prusa nozzle from the hotend assembly.

Step 11 Prusa Nozzle Parts Preparation

⬢For the following steps, please prepare:

⬢新しいPrusaノズル（１個）

See the Different Nozzle Types article for more info on the available options.

Step 12 Prusa Nozzle Installation

⬢Screw the new nozzle fully into the heater block until it touches the heater block surface.

⬢Hold the heater block securely using the 13-16 wrench.

⬢Use the 7mm cutout in the universal wrench to tighten the nozzle against the heater block. Avoid applying excessive force!

指定トルク値は1.5Nm（13.3lb-in）です。トルクレンチの使用を推奨します。

⬢Optionally, install the silicone sock.

Step 13 Hotend Assembly Parts Preparation

⬢For the following steps, please prepare:

⬢Hotend assembly (1x)

The CORE One hotend assembly has a Nextruder Silicone Sock installed by default. It is optional, and you can remove it at any time.

⬢For more information, read the article Nextruder Silicone Sock.

The default nozzle on the CORE One is the 0.4mm HF, (High Flow version) labeled CHT

Step 14 Hotend Insertion

⬢

Locate the corresponding opening on the bottom of the extruder heatsink and fully insert the hotend into the heatsink.

⬢

At the same time, keep the hotend cables pointing to the front, at a slight angle.

The assembly must fit into the recess in the fan shroud with appropriate clearance

⬢Keep pushing the hotend assembly upward and tighten both thumbscrews to secure it in place.

⬢Ensure the hotend is fully inserted into the heatsink. It should align as shown in the picture and must not protrude below the fan shroud.

Step 15 Nozzle Insertion Check

⬢Verify that the nozzle is fully inserted into the heatsink. The copper ring on the nozzle should not be visible if properly seated.

If not fully inserted, it can cause poor heat transfer, potentially leading to nozzle clogs.

ノズルの位置を調整するには、サムスクリューを緩めてノズルの位置を変え、ホットエンドアセンブリーを押し上げながらネジを締め直します。

Step 16 Hotend Cables Guidance

⬢Locate the cable guide (plastic hook) behind the thumb screws. Guide the thermistor cable through the channel first. Then insert the hotend heater cable.