JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

6B. Spool holder assembly

6B. Spool holder assembly

6B. Spool holder assembly
Relevant for:
Last updated 4 months ago
6B. Spool holder assembly
 Difficulty
Very easy
 Steps
9
 Available languages
ENCSPLDEESITFR
Spool holder: parts preparation
Spool holder: parts preparation
Spool holder: parts preparation
All the printed parts and fasteners needed for this chapter are included in the box: Print head & Heatbed
次のステップのために、次のものをご用意ください
MINI-base-spool-holder (4x)
MINI-rail-spool-holder (2x)
M3x12 screw (4x)
M3x8 screw (4x)
M3n nut (4x)
The list continues in the next step...
Spool holder: parts preparation
Spool holder: parts preparation
Spool holder: parts preparation
以下のステップに向けて、下記の部品を用意してください。
Bearing 608Z (4x)
Anti-vibration pad (4x)
スプールホルダーベースの組立て
スプールホルダーベースの組立て
スプールホルダーベースの組立て
スプールホルダーベースの組立て
Take two of the BASE parts and insert the M3n nuts into the holes in both of them - see the picture (they are identical). If you can't push them in, insert a screw from the opposite side to pull them in.
ベースパーツの1つをひっくり返して、ベアリングを2つ挿入します。
ベアリングの上に2つ目のベースパーツを置きます。
上からM3×12ネジを差し込み、締め付けます。ベースアセンブリをひっくり返し、同じようにします。
両方のベアリングが自由に回転することを確認します。回転しない場合は、ネジを少し緩めてください。
Repeat this step for the second base assembly.
スプールホルダーレールを追加
スプールホルダーレールを追加
スプールホルダーレールを追加
スプールホルダーレールを追加
1番目のベースの溝に両方のレールをスライドさせながら挿入します。ベースの端にレールを合わせます。
M3x8ネジ 2本で1つ目のベースを固定します。締め付けの際は、適度な力で行ってください。
レールに2つ目のベースをスライド挿入します。正確な位置はこの時点では重要ではなく、次のステップで調整します。
滑り止めパッドの貼り付け
滑り止めパッドの貼り付け
滑り止めパッドの貼り付け
Place a spool of the filament you wish to use in the spool holder. Align the second base to match the size of the spool. We are using a spool of Prusament as an example.
ホルダーが揃ったら、スプールを取り外し、M3x8ネジを2本挿入して締め、部品が動かないようにします。
Attaching anti-slip pads
Attaching anti-slip pads
Attaching anti-slip pads
Attaching anti-slip pads
同梱の切り欠き付き滑り止めシートを手に取り、4枚のパッドを取り出します。
保護フィルムを剥がし、スプールホルダーの底面にパッドを取り付けます。
注意: レールの近くやレールの上にパッドを取り付けると、あとで幅調整がしにくくなることがありますので、避けてください。
Spool holder is assembled!
Spool holder is assembled!
最終的な仕上がりを写真と比較しながら確認します。
That was easy, wasn't it? ;) Now it's finally time for the last chapter: 7. Preflight check
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us