Manual changelog

Relevant for:

MK3S

Last updated 3 years ago

Difficulty

Moderate

Steps

Available languages

Step 1 Versions history

⬢Versions of the MK3S manual:

⬢02/2019 - Initial version 3.10

⬢03/2019 - Updated to version 3.11

⬢07/2019 - Updated to version 3.12

⬢09/2019 - Updated to version 3.13

⬢06/2020 - Updated to version 3.14

⬢07/2020 - Updated to version 3.15

Step 2 Changes to the manual (1)

⬢03/2019 - Chapter 2 (Y-axis)

⬢PSU holders assembly now depends on the type of the PSU, which is in your kit.

⬢03/2019 - Chapter 7 (HB & PSU)

⬢Chapter 7 is now in two versions depending on the PSU type, which is in your kit.

New PSU is fully black, old PSU has silver casing.

Manual version 3.11

Step 3 Changes to the manual (2)

⬢05/2019 - Chapter 7 (HB & PSU)

⬢Heatbed-cable-cover design improved to prevent collision with the extruder cables, which sometimes occurred. All screws are now facing down.

⬢New design with circular holes in the top part. The smaller part has hexagonal holes.

⬢Old design with hexagonal holes in the top part. The smaller part has circular holes.

Manual version 3.11

Step 4 Changes to the manual (3)

⬢07/2019 - Chapter 1 (Introduction)

⬢The printer's package contains a lubricant, which is intended for maintenance. No need to use it now the bearings are lubricated. There is a dedicated online manual on how to clean the printer and apply the lubricant. See Maintenance tips

⬢Several tweaks and new photos across the entire manual.

Manual version 3.12

Step 5 Changes to the manual (4)

⬢09/2019 - Chapter 1 (Introduction)

⬢Added warning about the ESD protection. Keep the electronics in the bag until needed for the assembly.

⬢09/2019 - Chapter 5 (Extruder)

⬢There is a new hardware revision of the IR-sensor with some optimisations. Filament detection is the same.

Manual version 3.13

Step 6 Changes to the manual (4)

⬢06/2020 - Chapter 2 (Y-axis assembly)

⬢New photos across the chapter show the position of PSU holders M3nE for Black PSU.

⬢06/2020 - Chapter 5 (E-axis assembly)

⬢FS-cover assembly step is moved a few steps earlier to prevent the IR-sensor from being damaged during assembly.

⬢06/2020 - Chapter 8 (Electronics assembly)

⬢New photos in this chapter include cable guiding from the Black PSU.

Manual version 3.14

Step 7 Changes to the manual (5)

⬢07/2020 - Chapter 2 (Y-axis assembly)

⬢The correct orientation of the bearings on the Y-carriage has been adjusted.

⬢The correct orientation, the tracks (rows of the balls) are on the sides.

⬢The incorrect orientation, the track is in the middle of the hole.

⬢

The printed version of this manual (v3.14 and older) suggests a different approach, please follow the online version instead.

⬢Added instructions, how to glue the silver label on the frame.

Manual version 3.15

Manual changelog

Manual changelog

Step 1 Versions history

Step 2 Changes to the manual (1)

Step 3 Changes to the manual (2)

Step 4 Changes to the manual (3)

Step 5 Changes to the manual (4)

Step 6 Changes to the manual (4)

Step 7 Changes to the manual (5)

Comments

Still have questions?