Relevant for
Your printer is showing the message: "Overcurrent detected on xBuddy/Buddy heatbed port, disconnect the device."
Error name: Heatbed Port Overcurrent
Error code: #36309 (INDX) #31309 (CORE One) #35309 (CORE One L) #26309 (MK4S) #13309 (MK4) #27309 (MK3.9S) #21309 (MK3.9) #28309 (MK3.5S) #23309 (MK3.5) #12309 (MINI)
The error is shown when there is a damaged cable on the heatbed or any of its connections.
The most likely cause of this issue is damage to the heatbed cable. Check the path between the heatbed and the xBuddy/Buddy board, and see if there are any parts that are broken or pinched.
In case there is no damage, check the cable connection to the heatbed and to the xBuddy/Buddy board. Try reconnecting the connectors.
In rare cases, this error message can be shown in case of damage to the mainboard. So if the cables and connectors are intact, try checking the board for any damage.
![]() | ![]() |
| CORE One heatbed | MK4/S, MK3.9/S, MK3.5/S heatbed |
xBuddy board (CORE One, MK4/S, MK3.9/S, MK3.5/S)
![]() | ![]() |
| MINI/+ heatbed (bottom) | MINI/+ heatbed (top) |
![]() | ![]() |
| MINI/+ Buddy board | MINI/+ Buddy board |
24 comments
; FIX #13309 by preheating first the bed and then the hotend and only when everything is up to temp switch on the servos.
; Explanation: When doing a coldstart print often the Heatbed Overcurrent Alert gets triggered, my guess is that this is happening
; because powering everything on at the same time or short succession issues a massive current spike which then triggers
; the overcurrent alert. The manual workaround is to use the PREHEATING feature from the menu. With this EVERY print succeeds,
; without preheating every (coldstart) print fails.
; Error code: #13309 (MK4) #21309 (MK3.9) #23309 (MK3.5)
; Error name: Heatbed Port Overcurrent
; https://help.prusa3d.com/article/heatbed-port-overcurrent-13309-mk4-21309-mk3-9-23309-mk3-5_405612
; PREHEATING the bed and waiting 1 minute for it to get up to temperature. We are not waiting until it reaches full temperature because that
; would take a long time, but we want to give it a bit time so the current ramp up (I guess it draws most current at start) has time to die down a bit.
M140 S[first_layer_bed_temperature] ; set bed temp
G4 P60000 ; Wait 60 seconds
; Now after a minute we also heat up the hotend, here we can wait until it is hot because anyway the printer cannot continue without the hotend being ... hot.
M104 S{first_layer_temperature[0] * 0.75} ; set hotend to 75% of final temperature
M109 S{first_layer_temperature[0] * 0.75} ; wait for hotend to reach that temperature
; ORIGINAL PRUSA GCODE
Issue solved
I checked also the cables from and to the power supply. All OK, no short no open or intermediate connections found and also no bad isolation. The Buddy board does not show any visible damage.
After reassembling and running all tests, it worked well for3 Prints. Then the error message came again.
I preheated the bed to approx 40C first and then started a print the "normal" way, no problem anymore, The next 3 print (up to now) no problems.
To me it looks that sometimes the overcurrent detection is too sensitive. It has problems with the inrush current when Bed and Nozzle start heating together. Maybe the power supply has a problem with the start current, however it had no problem with it the last 1.5 years. I do not have a an oscilloscope the measure the inrush current.
Or it is some other firmware bug...... Maybe Prusa can look into the issue and give feedback.
I didn't use the printer for roundabout two month. Then I tried printing but I got the error several times when bed and nozzle started heating. I removed and reassembled the cables on the print bed and the buddy board but the issue prevailed. Luckily preheating the bed works.
I'm on firmware 6.4.0+11974 on a coreOne+