JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

Regular printer maintenance (XL)

Menu
Relevant for:
Last updated 17 days ago
This article is also available in following languages: 
ENCSPLDEESITFR

It is recommended to regularly take some time to maintain your Original Prusa XL. This should be done even if the printer is working perfectly. The inspection and maintenance of its various components should be done every ~200-300 hours of print time.

Useful tools

Besides the usual tools, such as Allen keys, needle-nose pliers, and IPA (IsoPropyl Alcohol) + paper towels, you might need:

  • Compressed air: also known as canned air. Be sure to not hold it upside down while spraying - otherwise, you could damage any electronic components while trying to clean them.
  • Brush: a small brass brush is a useful tool for cleaning the heaterblock. If you don't have a brass brush any brush with hard bristles will do the job. 
  • Prusa Lubricant: a tube of Prusa Lubricant is included with the Original Prusa XL. It is used in the Z-axis leadscrew paragraph. 
DO NOT use Prusa Lubricant on the linear rails! 

Axes check

Ensure that there is no debris or dust on the linear rails. If there is, clean them using a clean paper tissue or a clean cloth with NO de-greaser and with no chemicals, as these might damage the rubber in the carriage. The factory lubrication for linear rails is effective for at least 2 years. 

Z-axis leadscrew

After ~500 hours of print time, lubricate the Z-axis leadscrews.

  1.  Go into the printer menu to Control -> Autohome.
  2.  Lubricate the Leadscrew.
  3.  Go into the printer menu to Control -> Move axis -> Move Z, and move the axis all the way down.
  4.  Again go into the printer menu to Control -> Autohome.

After that, your lead screws will be lubricated.

Belt

Attach the belt tensioner on the top belt on the X-axis. The belt tensioner has a pointer, check if it is in the optimal range. The ideal position of the pointer is in the center area, closer to the max mark.

You can also use the Prusa Belt tuner app.

Side filament sensor

The side filament sensor on the printer may accumulate leftover filament over time. To prevent false readings, follow the guide How to clean the side filament sensor (XL) [進行中の翻訳].

Flexible steel sheet

All flexible steel sheets should be cleaned regularly to ensure adhesion, but the exact methods and washing solutions can differ depending on your type of sheet.

You can find more information on how to take care of your flexible steel sheet in this article.

Acetone should be used sparingly for cleaning, and only be used on the Smooth steel sheet! Never use acetone on the Textured or Satin steel sheet as the surface will be permanently damaged.

Fans

The Original Prusa XL is equipped with a hotend fan, and with a print fan. The printer can detect if any of its fans stop spinning. However, that does not mean you should not check them during maintenance. Dust or plastic build-up can decrease their efficiency or even damage them.

Both fans should be checked and cleaned after a few hundred hours of printing. With the fan not moving, dust can be removed with compressed air in a spray can, small plastic threads can be removed with tweezers.

Do not blow compressed air on a running fan: the fan can get damaged this way. 

Nextruder

When accessing the extruder parts, do not open the gearbox: this action can cause issues on the extrusion, and will void the printer warranty

The primary gear and the bearings attached to the Idler Shaft in the extruder do not need any lubricant. Over time, a deposit of filament debris can form in the grooves of the primary gear, which then causes insufficient filament extrusion. Access the extruder by lifting the Idler Nut, and then moving the Idle Shaft. You can blow away the dirt with compressed air, or use a brass brush or an ordinary toothpick. Use the access hole on the front of the extruder/tool head.

Heaterblock

CAUTION: Heated parts can cause severe burns!

If the heaterblock is covered with plastic, it can affect its thermal properties. To clean it, heat the nozzle for 3 to 5 minutes at 250 °C, and turn the printer off. Immediately after that use a small brass brush to clear away any old plastic stuck on the nozzle and heaterblock. Be extra careful around the fragile wires that join the heaterblock.

You can also use the Nextruder Silicone sock to protect your heater block.

Electronics

Every ~600-800 printing hours access the electronic boards for a visual check.

Before touching the electrical connections, please make sure that the printer is fully cooled down, switched off, and unplugged from the main power source for at least 10 minutes.
  • Check if there are any pinched or worn cables on the printer.
  • Access the electronic boards and blow compressed air in between the cables to get rid of dust. 
  • Check the connection of all of the wires on the electronic boards. 

Firmware and software

You should always be using the latest stable firmware version that we have published for your specific printer model. You can check the firmware version you have, by navigating to LCD menu - Info - Version info

We also recommend using the latest version of our PrusaSlicer, as it enables you to enjoy all the features of your printer. It even saves information about the printer model, nozzle diameter, and firmware version directly into the g-code file so that the printer can warn you if anything is out of date or incompatible.

Tool-changer/toolhead cleaning

This can be made along with the rest of the maintenance, or it can also be done if you notice that your prints have banding or ringing issues. The metal connection of the ToolHead and the ToolChanger needs to be lubricated to work smoothly. For that, use the guide How to lubricate the coupler pins on Original Prusa XL (Multi-Tool) [進行中の翻訳].

 

Was this article helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us